![BBE MAX-X2 [4/12] Specifications](/img/pdf.png)
BBE MAX-X2 [4/12] Specifications
![BBE MAX-X2 [4/12] Specifications](/views2/1000160/page4/bg4.png)
– iii –
SPECIFICATIONS Max-X2
CROSSOVER TYPE ………………………………………………………………………………………… Stereo 2 way
CROSSOVER FREQUENCY
LOW-HIGH ………………………………………………………………………………… 250Hz-6KHz
FILTER TYPE (SLOPE) ……………………………………………………… 2nd Order, 12dB/Octave
INPUTS: TYPE ………………………………………………………………………… XLR and unbalanced 1/4”
IMPEDANCE …………………………………………………………………………………… 100KOhms
OUTPUTS: TYPE …………………………………………………………………………………… Unbalanced 1/4”
IMPEDANCE …………………………………………………………………………………… 600 Ohms
LOW CUT FILTERS ………………………………………………………………………………… 30HZ, 12dB/Octave
FREQUENCY RESPONSE ………………………………………………………………………………20Hz - 25KHz
TOTAL HARMONIC DISTORTION (THD) ……………………………………………………………………… <.05%
S/N RATIO ………………………………………………………………………………………………………… >95dB
FUSE: 95-120V AC: ……………………………………………………………… 200mA 250VAC (slow-blow)
210-240V AC: ………………………………………………………… T100mAL 250VAC (slow-blow)
DIMENSIONS ……………………………………… 483mm(W) 194.5(D) 44mm(H) /19.01”(W) 7.66”(D) 1.73”(H)
WEIGHT ………………………………………………………………………………………………………2.5Kg (5.51lb)
SPECIFICATIONS
Содержание
- Safety related symbols 2
- Contents 3
- Specifications 4
- Caution to prevent malfunctioning and or possible equipment damage before plug ging the unit into the power source 1 the voltage selector switch should be set for the correct voltage for your area 115v or 230v and 2 all equipment connected to the crossover outputs should be turned off or all the inputs turned down 5
- Gett ng started 5
- Getting started 5
- Introduction 5
- Caution before pressing the phase switches always lower the outputs of your power amplifiers to avoid possible speaker damage 6
- Front panel 6
- Max x2 front panel 6
- 4 3 2 4 3 7
- Max x2 rear panel 7
- Rear panel 7
- Installation 8
- Max x2 typical setup 8
- Balanced 1 4 plug 9
- Balanced xlr f 9
- Balanced xlr m 9
- Connection cables 9
- In this chapter you ll find the wiring diagrams for the connectors to be used with your crossover take care of the connector cable always holding them by the connectors and avoiding knots and twists when coiling them this gives the advantage of increasing their life and reliability which is always to your advantage periodically check that your cables are in good condition that they are correctly wired and that all their contact are perfectly efficient a great number of problems faulty contacts ground hum discharges etc are caused entirely by using unsuitable or faulty cables 9
- Installation 9
- Xlr female jack unbalanced link xlr female jack unbalanced link 9
- Xlr male jack unbalanced link 9
- Do not return any product to the above address without instructions and authorization issued by the above location 10
- Warranty 10
Похожие устройства
- Alesis SR16 Инструкция по эксплуатации
- Sharp CD-E700WR Инструкция по эксплуатации
- Samsung LE-32C550 Инструкция по эксплуатации
- Festool CARVEX PSBC 400 GG 561402 Инструкция по эксплуатации
- Chevrolet Lanos Инструкция по эксплуатации
- Brother INNOV-IS 4000 Инструкция по эксплуатации
- Brother PR650e Инструкция по эксплуатации
- Festool CARVEX PSC 400 EB-Set 561403 Инструкция по эксплуатации
- Sharp CD-DV600WR Инструкция по эксплуатации
- Chevrolet Aveo Инструкция по эксплуатации
- Samsung LE32D551K2W Инструкция по эксплуатации
- Alesis TRANSACTIVE 50 Инструкция по эксплуатации
- Astralux 100 Инструкция по эксплуатации
- Chevrolet Spark Инструкция по эксплуатации
- Sharp CD-BK300WR Инструкция по эксплуатации
- Bosch GUS 10.8 V-LI 0.601.9B2.901 Инструкция по эксплуатации
- Samsung LE46D551K2W Инструкция по эксплуатации
- Alesis IO|14 FireWire Инструкция по эксплуатации
- Astralux 545 Инструкция по эксплуатации
- Bosch BSGL 52242 Инструкция по эксплуатации