![Robomow MS1800 [50/58] Code description corrective action](/img/pdf.png)
Robomow MS1800 [50/58] Code description corrective action
![Robomow MS1800 [50/58] Code description corrective action](/views2/1172599/page50/bg32.png)
49
EN
9.4.1 Description of No-Depart Codes
Code Descripon Correcve Acon
00
None. Automatic departure is working properly None. Wait for the end of current charging cycle
01
Mower’s battery is not yet in the required state
forautomatic departure
None. Wait for the end of current charging cycle.
May take longer than usual
02
Inactive Time is activated. No automatic
departure during Inactive Time
None. Validate Inactive Time settings (see
Section 6.4.1.3)
03
Mowing cycle is completed. Waiting for the next
scheduled operation
None
04
Humid conditions or rain were detected during
last 30 minutes.
- None. If the rain has stopped, wait for another
30 minutes at least
- If there was no any raining at all, consider
adjusting rain sensor’s sensitivity (see P008 in
Section 6.4.2) or call Robomow Hotline
05
The mower is switched off Switch on the Safety Switch
07
User response (interaction) is required in order to
continue current operation
Acknowledge the error message
08
Multiple consecutive mowing operations were
shorter than expected. Usually accompanied by
U018 (“Operation time is shorter than expected”)
- Inspect mower’s blade and drive wheels.
- Battery run-time may be too short.
09
One-Time setup is running
One-Time setup should be completed before the
automatic operation can start
11
Automatic operation is disabled by menu P021
(see Section 6.4.2)
Enable automatic operation through menu p021
12
Automatic operation is put on pause bythe Power
Box
Enable automatic operation via the Power Box.
13
All week days are set as inactive days
Validate Inactive Time settings (see Section
6.4.1.3)
14
The mower is being charged directly by the
Power Box (via the DC connector)
Disconnect the DC cable from the mower. Put
the mower in the Base Station.
15
Battery cells are being balanced in special
charging mode
None. Wait for the end of current charging cycle.
May take longer than usual.
16
The mower is in the Base Station, but there is no
charging voltage supply
- Inspect Power Box’s connection to the Base
Station
- Conrm that nothing is blocking the charging
pins
17
Low ambient temperature
None. The mower will automatically depart
when it gets warmer.
18
Sub-Zone entry problem. The mower was unable
to enter one of the Sub-Zones
Refer to U090-U093 in Section 9.3
Содержание
- Operation and safety manual 2
- Table of contents 3
- Chapter 1 4
- Important 4
- Introduction and safety 4
- 7 6 5 4 3 2 5
- Safety warnings precautions 5
- Warning decal definitions 5
- Robomow safety features 7
- Chapter 2 8
- Know your robomow 8
- What s in the box 8
- How robomow works for you 9
- Robomow features 10
- Chapter 3 11
- Lawn types what does your lawn look like 11
- Planning ahead 11
- Main sub zone with a narrow pass 12
- Main zone sub zone s type lawn 12
- Separated zone 12
- Separated zones type lawn 12
- A separated zone larger than 100 m² 1100 ft² 13
- A separated zone smaller than 100 m² 1100 ft² 13
- Base station location guidelines 13
- Select base station location 13
- Setups 13
- Types of separated zone 13
- At a corner 14
- External setup off the lawn perimeter 14
- Internal setup on the lawn perimeter 14
- Main zone 14
- Outside the lawn 14
- There are two types of external setup 14
- Objects inside 15
- Planning the perimeter wire layout 15
- Select power box location 15
- Slopes 15
- Distances from the edge pools ponds cliffs etc 16
- Interference with adjacent lawns 16
- Chapter 4 17
- Initial setup 17
- Perimeter wire setup 17
- Preparations 17
- Laying the perimeter wire 18
- Starting point perimeter wire at the base station area 18
- Important information 19
- Min 1 m 4ft 19
- Perimeter wire within the working area 20
- Main zone 21
- Min 50cm 21
- Sub zone 21
- Main zone 22
- Min 50cm 22
- Sub zone 22
- Fastening perimeter wire to the 23
- Ground 23
- Main zone 23
- Back at the base station completing the perimeter wire setup 24
- Connecting the power box 25
- Laying and fastening extension cable 25
- Placement and connection of the base station 25
- At the power box location 26
- Determining the perimeter switch location 27
- Laying out the perimeter wire 27
- Perimeter switch placing options 27
- Setup in a non base zone 27
- At the perimeter switch s location 28
- Chapter 5 30
- Preparing robomow 30
- No wire signa 31
- Peg bas 31
- Position 31
- Reposition base station 31
- Swap wires in plot connecto 31
- Area setting indicator 33
- Automatic operation 33
- Battery and charging indicator 33
- Chapter 6 33
- Day and time setting indicator 33
- Days of the week 33
- Inactive time setting indicator rain sensor 33
- Mower is in the base station indicator 33
- Mowing hours setting indicator 33
- Operating panel 33
- Red lit constantly low battery green blinking charging green lit constantly fully charged 33
- Robomow operation 33
- User error messages 33
- Chapter 6 34
- Robomow operation 34
- Basic settings 35
- Menu options 35
- Screen setting description options 36
- Screen setting description options 37
- Screen setting description options 38
- Screen setting description options 39
- Operation in a non base zone using a perimeter switch 40
- Robomow app settings 40
- Chapter 7 41
- Enable disable the automatic operation 41
- Event description 41
- Power box alerts 41
- Turn the buzzer on off 41
- Using the power box 41
- Chapter 8 42
- Charging 42
- Chapter 9 43
- General error codes 43
- Robomow error codes table 43
- Troubleshooting and user messages 43
- Display message probable cause event corrective actions 44
- Detailed error codes 45
- Display message probable cause event corrective actions 45
- Display message probable cause event corrective actions 46
- Display message description required action 47
- User messages 47
- Basic troubleshooting 48
- Display message description required action 48
- Problem encountered probable cause event corrective actions 48
- U090 u093 48
- Problem encountered probable cause event corrective actions 49
- Code description corrective action 50
- Description of no depart codes 50
- Anti theft disabling device pin code write down your 4 digit anti theft disabling device pin code refer here if you ever forget the code 51
- Chapter 10 51
- Product specification 51
- Rc304 rc308 rc312 51
- Robomow serial number 51
- _______________________ 51
- Chapter 11 52
- Maintenance and storage 52
- Maintenance of the blade 53
- Lightning storm 54
- Maintenance of the base station area 54
- Splicing the perimeter wire 54
- Accessories 55
- Chapter 12 55
- Chapter 13 56
- Robomow lawn care has never been so easy 56
- Tips for maintaining your lawn 56
- Always follow the safety instructions specified in this user manual 57
- C series limited warranty 57
- Warranty card 57
Похожие устройства
- Robomow MS1800 Инструкция QuickStart
- Robomow CITY110 Инструкция по эксплуатации
- Robomow CITY110 Инструкция QuickStart
- Robomow TS1000 Инструкция по эксплуатации
- Robomow TS1000 Инструкция QuickStart
- Robomow TS1800 Инструкция по эксплуатации
- Robomow TS1800 Инструкция по эксплуатации
- Robomow TC150 Инструкция по эксплуатации
- Robomow TC150 Инструкция QuickStart
- Robomow CITY120 Инструкция по эксплуатации
- Robomow CITY120 Инструкция QuickStart
- Robomow TC300 Инструкция по эксплуатации
- Robomow TC300 Инструкция QuickStart
- Robomow TC500 Инструкция по эксплуатации
- Robomow TC500 Инструкция QuickStart
- Robomow TUSCANIA200 Инструкция по эксплуатации
- Robomow TUSCANIA200 Инструкция QuickStart
- Lenovo ideacentre c260, 57-331339 Инструкция по эксплуатации
- Robomow TUSCANIA500 Инструкция по эксплуатации
- Robomow TUSCANIA500 Инструкция QuickStart