Hotpoint-Ariston IX 644 CRFH E — правила подключения электрической варочной панели и духового шкафа [4/32]
![Hotpoint-Ariston IX 644 CRFH E [4/32] Start up and use](/views2/1173958/page4/bg4.png)
4
GB
Electrical connection
! The electrical connection for the hob and for any built-
in oven must be carried out separately, both for safety
purposes and to make extracting the oven easier.
Single-phase connection
The hob is equipped with a pre-connected electricity supply
cable, which is designed for single-phase connection.
Connect the wires in accordance with the instructions given
in the following table and diagrams:
Other types of connection
If the mains supply corresponds with one of the following:
Voltage and mains frequency
• 400V - 2+N ~ 50/60 Hz
• 220-240V 3 ~ 50/60 Hz
Separate the wires and connect them in accordance with
the instructions given in the following table and diagrams:
Connecting the electricity supply cable to the mains
If the appliance is being connected directly to the electricity
mains an omnipolar switch must be installed with a minimum
opening of 3 mm between contacts.
! The installer must ensure that the correct electrical
connection has been made and that it is fully compliant
with safety regulations.
Before connecting the appliance to the power supply, make
sure that:
• The appliance is earthed and the plug is compliant with
the law.
Voltage and
mains frequency
Electrical cable Wire connection
220-240V 1+N ~
50/60 Hz
: yellow/green
N: the two blue wires together
L: brown and black together
Voltage and
mains frequency
Electrical cable Wire connection
400V - 2+N ~
50/60 Hz
220-240V 3 ~
50/60 Hz
: yellow/green;
N: the two blue wires
together
L1: black
L2: brown
Fix the hob as follows:
1. Use short flat-bottomed screws to fix the 4 alignment
springs in the holes provided at the central point of each
side of the hob.
2. Place the hob in the cavity, make sure it is in a central
position and push down on the whole perimeter until the
hob is stuck to the supporting surface.
! The screws for the alignment springs must remain
accessible.
! In order to adhere to safety standards, the appliance
must not come into contact with electrical parts once it
has been installed.
! All parts which ensure the safe operation of the
appliance must not be removable without the aid of a tool
Start-up and use
! The glue applied on the gaskets leaves traces of grease
on the glass. Before using the appliance, we recommend
you remove these with a special non-abrasive cleaning
product. During the first few hours of use there may be a
smell of rubber which will disappear very quickly.
! A few seconds after the hob is connected to the electricity
supply, a buzzer will sound. The hob may now be switched
on.
Types of noise during normal hob operation:
• Buzz: due to the vibration of the metallic parts that
make up the induction element and the pot; it is
generated by the electromagnetic field required for
heating and increases as the power of the induction
element increases.
• Soft whistle: heard when the pot placed on the heating
zone is empty; the noise disappears once food or water
is placed into the pot.
• Crackle: produced by the vibration of materials on the
bottom of the pot due to the flow of parasitic currents
caused by electromagnetic fields (induction); can be
more or less intense depending on the material making
up the bottom of the pot, and decreases as the pot
dimensions increase.
• Loud whistle: heard when two induction elements of
the same group function simultaneously at maximum
power and/or when the booster function is set on the
larger element while the other is auto-adjusted. Noise
is reduced by decreasing the power level of the auto-
adjusted induction element; pot bottom layers made of
different kinds of materials are among the main causes
of this noise.
• The socket can withstand the maximum power of the
appliance, which is indicated on the data plate located
on the appliance itself.
• The voltage falls within the range of values indicated on
the data plate.
• The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an authorised
technician to replace it. Do not use extension cords or
multiple sockets.
! Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by
authorised technicians only.
! The manufacturer declines any liability should these
safety measures not be observed.
! Do not remove or replace the power supply cable for any
reason. Its removal or replacement will void the warranty
and the CE marking. INDESIT does not assume liability for
accidents or damage arising from replacement/removal
of the original power supply cable. Replacement can only
be accepted when carried out by personnel authorised
by INDESIT and using an original spare part.
Содержание
- Description of the appliance p.2
- Installation p.2
- Positioning p.2
- Installation of the safety washer p.3
- Start up and use p.4
- Electrical connection p.4
- Setting the power management p.5
- When power is initially applied to the cooktop the touch control conducts a calibration process for the touch keys which requires a low level of ambient li ght in the area of the touch keys if excessive ambient lighting is detected the user interface displays fl error and the calibration is suspended the error will disappear when satisfactory ambient lighting is de tected and the touch control calibration procedure will now complete satisfactorily p.5
- Loock button p.5
- After connecting the hob to the electrical grid the touch pannel might be automatically locked to un clock the pannel press and hold the control panel p.5
- The cooktop is switched on when a beep sound is emitted and the cooking zones display shows the 0 p.5
- Switching on the hob p.5
- Switching on the cooking zones p.5
- Initial light conditions p.5
- Then the countdown stops and the timer changes to time selection status wa iting a time selection p.6
- Switching off the hob p.6
- Switching off the cooking zones p.6
- Starting timer countdown the countdown starts 10 seconds after the last ope ration over the p.6
- If any power is selected a beep sounds and the timer display stops blinking the same happens to the led heater the last minute will be displayed in seconds p.6
- Fast boil booster function p.6
- End of timer countdown p.6
- Control panel lock p.6
- With the heater at booster level if the key is touched an error beep sounds and the cookset doesn t change with the heater at booster level if the key is touched a beep sounds and the cookset is reduced to 9 p.6
- When the timer is in countdown the user can chan ge the time at any time by touching the p.6
- Using the timer p.6
- When one or more keys are activated for more than 10 sec the touch control switches off a warning beep sounds is emitted every 10 sec while the key s is are activated with all heaters at zero power during 10 sec the cooktop is switched off if the switching off is due to an accidental activa tion of keys the touch control actuates as above p.7
- Safety devices p.7
- Practical advice on using the appliance p.7
- Practical cooking advice p.8
- Precautions and tips p.9
- General safety p.9
- Disposal p.9
- Technical description of the models p.10
- Switching the appliance off p.10
- Ix 644 crfh e p.10
- Disassembling the hob p.10
- Cleaning the appliance p.10
- Care and maintenance p.10
- Ix 644 crfh e p.11
- Описание устройства p.12
- Установка p.12
- Установка на место p.12
- Установка предохранительной шайбы p.13
- Электрическое подключение p.14
- Включение и эксплуатация p.14
- Включение варочной панели p.15
- Варочная панель будет включена когда будет слышен звуковой сигнал и на дисплеях варочных зон появится 0 p.15
- Условия низкой освещенности p.15
- После подключения варочной панели к сети питания сенсорная панель будет автоматически заблокирована для разблокировки панели нажмите и удерживайте кнопку control panel loock блокировка сенсорной панели p.15
- Настройка функции power management управление электропитанием p.15
- Когда в варочную панель первоначально поступает электроэнергия сенсорная панель осуществляет процесс градуировки сенсорных клавиш при этом требуется низкий уровень внешнего освещения в области сенсорных клавиш если будет обнаружено избыточное внешнее освещение на пользовательском интерфейсе отобразится ошибка fl и градуировка будет приостановлена ошибка исчезнет когда уровень освещения будет удовлетворительным и процедура градуировки сенсорной панели будет завершена удовлетворительно p.15
- В случае включения усилителя мощности в нагревательном элементе и при нажатии кнопки будет слышен звуковой сигнал сигнализирующий ошибку и изменения настроек варочной панели не будут выполнены в случае включения усилителя мощности в нагревательном элементе и при нажатии кнопки будет слышен звуковой сигнал и уровень мощности варочной панели будет снижен до 9 p.16
- Выключение варочных зон p.16
- Включение обратного отсчета таймера обратный отсчет начинается через 10 секунд с момента последнего использования кнопок p.16
- Включение варочных зон p.16
- Функция fast boil booster быстрое кипячение усилитель мощности p.16
- Использование таймера p.16
- Если будет выбрана мощность будет включен звуковой p.16
- Сигнал и дисплей таймера прекратит мигать то же произойдет со светодиодным индикатором нагревательного элемента последняя минута будет отображаться в секундах p.17
- Блокировка панели управления p.17
- Практические советы по эксплуатации изделия p.17
- Обратный отсчет будет остановлен и таймер перейдет в режим ожидания выбора времени p.17
- Когда на таймере включится обратный отсчет пользователь может изменить время в любой момент с помощью кнопок p.17
- Выключение обратного отсчета таймера p.17
- Выключение варочной панели p.17
- Когда одна кнопка или несколько кнопок нажаты и используются в течение более 10 секунд панель управления отключается предупреждающий звуковой сигнал будет звучать каждые 10 секунд пока данная кнопка и не будут выключены если уровень мощности всех нагревательных зон будет составлять 0 в течение 10 с то варочная панель будет отключена если отключение будет обусловлено случайным нажатием кнопок то сенсорная панель управлния будет включена как описано выше p.18
- Защитные устройства p.18
- Приготовление на умеренном огне приготовление на малом огне p.19
- Приготовление на большом огне приготовление на среднем огне p.19
- Практические советы по приготовлению блюд p.19
- Утилизация p.20
- Предосторожности и рекомендации p.20
- Общие правила безопасности p.20
- Чистка изделия p.21
- Техническое обслуживани и уход p.21
- Порядок демонтажа варочной панели p.21
- Отключение электропитания p.21
- Условные обозначения p.22
- Система индукционного нагревания является самой быстрой из существующих технологий нагрева в отличие от традициональных конфорок нагрев производится не варочной зоной нагревается непосредственно содержимое кастрюли дно которой обязательно должно быть из ферромагнитного материала p.22
- Техническое описание моделей p.22
- I варочная зона с простой индукцией b вольтодобавочное устройство индукционная варочная зона может иметь дополнительное p.22
- Ix 644 crfh e p.23
- Құралдың сипаттамасы p.24
- Орнату p.24
- Орналастыру p.24
- Шайбаны орнату p.25
- Электр байланысы p.26
- Іске қосу жəне пайдалану p.26
- Құлыптау түймесін басып тұрыңыз p.27
- Қуат реттегішін орнату p.27
- Қуат басында пісіру тақтасына қолданылғанда сенсорлы тақта сенсорлы түймелерге арналған дəлдеу процесін жүргізеді ол үшін сенсорлы түймелер аймағындағы жалпы жарық төмен деңгейде болуы керек жалпы жарық мөлшері артық болса пайдаланушы интерфейсінде fl қатесі көрсетіліп дəлдеу процесі тоқтатылады жалпы жарық деңгейі қажетті мөлшерде болғанда қате жоғалып сенсорлы тақтаны дəлдеу процесі соңына дейін жетеді p.27
- Плитаны қосу p.27
- Плитаны электр желісіне қосқаннан кейін сенсорлы тақта автоматты түрде құлыпталып қалуы мүмкін тақтаны құлыптан босату үшін басқару тақтасын p.27
- Дыбыстық сигнал берілгенде плита қосылып пісіру аймақтарының дисплейінде 0 көрсетіледі p.27
- Бастапқы жарық жағдайлары p.27
- Таймерді пайдалану p.28
- Таймер кері санағының басталуы кері санақ p.28
- Таймер кері санағының аяқталуы p.28
- Таймер жүріп жатқанда пайдаланушы p.28
- Пісіру аймақтарын өшіру p.28
- Пісіру аймақтарын қосу p.28
- Кері санақ тоқтап таймер уақытты таңдау күйіне ауысып уақыттың таңдалуын күтеді p.28
- Қыздырғыш күшейткіш деңгейінде тұрып түймесі түртілсе қате дыбыстық сигналы беріліп параметр өзгермейді қыздырғыш күшейткіш деңгейінде тұрып түймесі түртілсе дыбыстық сигналы беріліп параметр 9 ға түседі p.28
- Қуат деңгейі таңдалса дыбыстық сигнал беріліп таймер дисплейі жыпылықтауын тоқтатады қыздырғышы жд да солай болады соңғы минут секундпен көрсетіледі p.28
- Тез қайнату күшейткіш функциясы p.28
- Құралды пайдалану бойынша тəжірибелік кеңестер p.29
- Сақтандыру құрылғылары p.29
- Плитаны өшіру p.29
- Басқару тақтасын құлыптау p.29
- Тағамды дайындау жөніндегі тəжірибелік кеңестер p.30
- Қолданыстан алып тастау p.31
- Қауіпсіздіктің жалпы талаптары p.31
- Сақтық шаралары жəне кеңестер p.31
- Үлгілердің техникалық сипаттамасы p.32
- Пісіру тақтасын демонтаждау p.32
- Күтім жасау жəне техникалық қызмет көрсету p.32
- Аспапты тазарту p.32
- Аспапты сөндіру p.32
Похожие устройства
-
Hotpoint-Ariston ikia 640 cИнструкция по эксплуатации -
Hotpoint-Ariston SIO 6 RFHИнструкция по эксплуатации -
Zanussi IPZ6450KCИнструкция к устройству -
Hotpoint HS 3560B BFРуководство по работе с устройством -
AKPO PIA 6094015K IVИнструкция к устройству -
AKPO PIA 6094015K WHИнструкция к устройству -
AKPO PIA 6094015K BLРуководство по использованию -
Smeg SI2M7643DWРуководство по работе с устройством -
Weissgauff HI 649 Dual Flex PremiumРуководство по эксплуатации -
DELVENTO V30I72S210Руководство по эксплуатации -
Midea MIH65783FИнструкция по эксплуатации -
Midea MIH67783SBИнструкция по эксплуатации
Узнайте, как правильно подключить электрическую варочную панель и духовой шкаф. Следуйте инструкциям для безопасного и эффективного подключения.