Microlab m1910 Инструкция по эксплуатации онлайн
Prior to initial use, please read the manual carefully
M-1910
User Manual
www.microlab.cn
Microlab Electronics Co.,Ltd
Made in China
All symbols and logo belong to the respective brand holder or registered holder. All specifications and information are subject to changes without
further notice. Slight variations and differences might appear between the printed photos and actual product due to product enhancement.
Multimedia Speaker
80-M1910-97-0001-01 2012-05-09 (Change remote control and front panel)
Содержание
- Back cover 1
- M 1910 1
- M1910 97 0001 01 2012 05 09 change remote control and front panel 1
- Multimedia speaker 1
- User manual 1
- Check if the audio and speaker cables are well connected 2
- Check if the volume is at lower level and the mp3 format is recorded at above 196 bitrate 2
- Check of the audio source is working well 2
- Check the 3 mm stereo cable for proper connection and cable is firmly inserted intermittent sound 2
- English 2 2
- Ensure volume is correctly adjusted 2
- Frequently asked questions answers 2
- Frequently asked questions faq 2
- It is magnetically shielded so can be placed near lcd tv monitor without any distortion 2
- M1910 97 0001 01 2012 05 09 change remote control and front panel 2
- No sound 2
- Please ensure fresh batteries are inside the battery compartment of the remote control 2
- Sound is distorted 2
- Technical information 2
- Try to use it nearer to the subwoofer 2
- What are the products supported 2
- Where to place this speaker 2
- Wireless volume intermittent infrared remote control 2
- Above the lcd monitor or tv 3
- Adjust the volume on the media player and speaker master volume to your preferred listening level 3
- Caution 3
- Connect from the digital processor to the toslink port at the rear of the subwoofer with the included 3
- Connect the 5 input channels respectively to the rear panel 5 channel rca inputs 3
- Connect the center satellite to the center output at the rear panel of the subwoofer and place this 3
- Connect the playback device to the rear stereo rca inputs with the included signal cable 3
- Connect the rear satellites to the rear left and right outputs 3
- Connect the satellites to the left and right rca outputs at the rear panel of the subwoofer 3
- Connections 3
- Control features input selection sound effect level adjustments and mute 3
- Ensure the ac power supply match the power requirement printed at the rear panel 3
- Ensure the master volume is at the lowest setting 3
- Explanation of graphical symbols 3
- For 5 channel source 3
- For coaxial source 3
- For more input options depress the master volume to toggle the different input source types the 3
- For optical source 3
- For remote control simply point directly at the subwoofer and adjust the volume control the remote 3
- For short pause during playback depress the mute button to silence the system 3
- For sound effects bass and front levels can be adjusted from the front panel or remote control 3
- For stereo source 3
- For the remote control please ensure fresh battery is correctly loaded 3
- Important safety instructions 3
- M1910 97 0001 01 2012 05 09 change remote control and front panel 3
- Next connect the power cable at the rear of the subwoofer to the ac power supply source please 3
- Operations 3
- Optical cable 3
- Place both satellites on extreme sides of the listening position 3
- Place both satellites to the extreme sides at the rear of the listening position 3
- Place the subwoofer on the floor and with its back near the wall for more bass 3
- Remote control 3
- Start the playback device and song 3
- Subwoofer 3
- The power led will illuminate and the default 5 mode will be displayed 3
- The system can be placed temporary on hold by depressing the st by button on the front panel or 3
- The volume control is factory defaulted at the value 16 3
- Toggle will loop the selections from 5 to au 16 co 16 op 16 and then back to 5 again the led display 5 represents the source selection from the 5 channel connections au 16 represents the aux stereo channel co 16 represents the coaxial connection and op 16 represents the optical toslink connection 3
- Turn on the main ac power and switch on the speaker system from the rear power switch 3
- Use the included coaxial cable and connect from digital processor to the coaxial port at the rear of the 3
- Warnings 3
- Connections 4
- Features 4
- Front panel rear panel 4
- Front view 4
- Illustrations 4
- Introduction 4
- M1910 97 0001 01 2012 05 09 change remote control and front panel 4
- Package contents 4
- Remote control 4
Похожие устройства
- Microlab b51 Инструкция по эксплуатации
- Microlab solo-9c Инструкция по эксплуатации
- Microlab solo-6c new Инструкция по эксплуатации
- Microlab h30bt Инструкция по эксплуатации
- Microlab h30bt Инструкция по эксплуатации
- Microlab m200 platinum Инструкция по эксплуатации
- Microlab md112 Инструкция по эксплуатации
- Microlab fc30 Инструкция по эксплуатации
- Microlab B53 Инструкция по эксплуатации
- Microlab B72 Инструкция по эксплуатации
- Microlab M520 Инструкция по эксплуатации
- Microlab iH11, black Инструкция по эксплуатации
- Microlab M500U Инструкция по эксплуатации
- Microlab SOLO-15 Инструкция по эксплуатации
- Microlab M111 Инструкция по эксплуатации
- Microlab M200 Инструкция по эксплуатации
- Microlab SOLO-3C Инструкция по эксплуатации
- Microlab SOLO-2C Инструкция по эксплуатации
- Microlab SOLO-1C (MK-3) Инструкция по эксплуатации
- Microlab X15 Инструкция по эксплуатации
Скачать
Случайные обсуждения
Ответы 1
Какие меры безопасности рекомендуется соблюдать при использовании данной аудиосистемы?
2 года назад