Moxa OnCell G3110-T Руководство по аппаратной части онлайн
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Moxa OnCell G3110-T Руководство по аппаратной части онлайн

Moxa OnCell G3110 Руководство по аппаратной части онлайн
– 1 – – 2 – – 3 – - 4 -
P/N: 1802031000014
OnCell G3100
Quick Installation Guide
Fourth Edition, April 2014
Overview
There are currently six models in the OnCell G3100 series of
IP-gateways: the OnCell G3110, OnCell G3150, OnCell G3110-HSPA,
and OnCell G3150-HSPA. The main difference between the models is
the serial interface type and cellular connection speed. The OnCell
G3100 industrial RS-232, RS-232/422/485 GSM/GPRS/EDGE, or
UMTS or HSPA IP gateways are some of the most affordable, secure,
and versatile products available in the cellular networking market
today. These gateways also provide remote access and TCP/IP
support, and can be configured over a network.
Package Checklist
Before Installing the OnCell G3100 IP gateway, verify that the
package contains the following items:
Standard Accessories
• Document & Software CD
• Omni 1 dBi rubber SMA antenna (OnCell G3100 model name:
ANT-CQB-ASM-01; OnCell G3100-HSPA model name:
ANT-WCDMA-ASM-1.5)
• Din-Rail Kit
• 5-pin terminal block (screw type)
• 10-pin terminal block (screw type)
• Product warranty statement
• Quick Installation Guide
Optional Accessories
• Power Adaptor: 1.2 A (or above) @ 12V
• DC power supply
• Power jack to terminal block cable
• Quad-band GSM/GPRS/EDGE antennas for OnCell
G3110/G3150 series (impedance = 50 ohms):
ANT-CQB-AHSM-00-3m: Omni 0dBi/10cm, magnetic SMA
antenna, 3 m
ANT-CQB-AHSM-03-3m: Omni 3dBi/25cm, magnetic SMA
antenna, 3 m
ANT-CQB-AHSM-05-3m: Omni 5dBi/37cm, magnetic SMA
antenna, 3 m
Note: Please notify your sales representative if any of the above
items are missing or damaged.
Hardware Introduction
Front Views
Rear View
OnCell
G3110/G3150
OnCell G3110-HSPA/
OnCell G3150-HSPA
Top View
Bottom Views
OnCell G3110/G3110-HSPA
OnCell G3150/G3150-HSPA
Side Views
Reset Button
Press the Rest button continuously for 5 sec to load factory defaults:
Use a pointed object, such as a straightened paper clip or toothpick,
to press the reset button. This will cause the Ready LED to blink on
and off. The factory defaults will be loaded once the Ready LED stops
blinking (after about 5 seconds). At this point, you should release
the reset button (the default IP is 192.168.127.254).
LED Indicators
The LED indicators on the front panel of the OnCell G3100 are
described in the following table.
LED
Name
LED
Color
LED Function
Power
Green
Off
Data
Green
Amber
Off
GSM
Amber
Off
GRPS
Amber
Off
UMTS
Amber
Off
HSPA
Amber
Off
Ready
Green
Blinking slowly (1 sec): The OnCell has been
Off
Fault
Red
Blinking slowly (1 sec): Cannot get an IP
Off
Signal
(3 LEDs)
Green
(at least 2 LEDs must illuminated for data
Digital Input and Output
Six terminals on the terminal block are reserved for the I/O ports,
with 2 terminals used for each input, and 2 terminals used for each
output.
Digital Input—Digital ON and OFF determine which power input is
used:
• +13 to +30 V for state “1” (On)
• +3 to -30 V for state “0” (Off)
Digital Output—The default for the relay output (DOUT) is open,
indicating a normal condition. If the relay output (DOUT) is shorted,
it indicates an exception.
Adjustable pull high/low resistor for RS-485 Port
DIP switches on the bottom of the OnCell G3100 are used to set the
pull high/low resistor value for each serial port.
SW
1
2
3
Pull High
Pull Low
Terminator
ON
1 KΩ
1 KΩ
120 Ω
OFF
150 KΩ
150 KΩ
–
Hardware Installation Procedure
STEP 1: Open the SIM cover, and insert the SIM card in the SIM card
slot.
STEP 2: Connect the 12-48 VDC power adaptor to the OnCell G3100
and then plug the power adaptor into a DC outlet.
STEP 3: To configure the OnCell, use an Ethernet cable to connect
the OnCell directly to your computer’s Ethernet interface.
STEP 4: Connect the OnCell G3100’s serial Ethernet port to a serial
or Ethernet device.
Software Installation Information
The Document & Software CD contains the User’s Manual, OnCell
Search Utility, and OnCell Driver Manager. Insert the CD and follow
the on-screen instructions. Please refer to the User’s Manual for
additional details on using the OnCell Search and Driver Manager.
Pin Assignments and Cable Wiring
DB9 Male Port Pinouts
Note that the OnCell G3110 only supports RS-232. The RS-422/485
pin assignments only apply to the OnCell G3150.
DB9 Male
Pin
RS-232
1
DCD
2
RxD
3
TxD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
---

Содержание

Похожие устройства

Скачать