Bosch TDS 2229 [14/120] Trouble shooting

Bosch TDS 2229 [14/120] Trouble shooting
14
en
Troubleshooting
Problem Possiblecauses Solution
Pilot light (11) ashes Boiler and lter must be rinsed. Rinse the lter and the boiler according to
the cleaning instructions in this manual (see
section E).
The steam generator
does not come on.
There is a connection problem.
The main power button is not
switched on.
Check the mains cable (6), the plug and
the socket.
Set the main power button (12) to the “I”
position (illuminated in red).
The iron does not
heat up.
The main power button is not
switched on.
The temperature is set to a low
position.
Set the main power button (12) to the “I”
position (illuminated in red).
Set the temperature to the desired
position.
The iron begins to
smoke when switched
on.
During rst use: certain components
on the appliance have been lightly
greased at the factory and may
produce a little smoke when initially
heated.
During subsequent use: the soleplate
may be soiled.
This is completely normal and will stop
after a short while.
Clean the soleplate according to the
cleaning instructions in this manual.
Water ows through
the holes on the
soleplate.
The steam function is being used
before it has reached the correct
temperature.
The water is condensing inside the
pipes because steam is being used
for the rst time or has not been used
for a long time.
Reduce the steam ow when ironing at low
temperatures.
Point the iron away from the ironing area
and press the steam release button until
steam is produced.
Dirt comes out through
the soleplate.
There is a build up of scale or
minerals in the steam tank.
Chemical products or additives have
been used.
Use tap water mixed 50% with distilled
or demineralised water. To prolong the
optimum steam function, mix tap water
with distilled water 1:1. If the tap water in
your district is very hard, mix tap water
with distilled water 1:2.
Clean the soleplate with a damp cloth.
Never add products to the water.
The iron does not
produce any steam.
The boiler is not switched on or the
water tank is empty.
The steam regulation is set to the
minimum position.
Set the main power button (12) to the “I”
position (illuminated in red), and/or ll the
water tank.
Increase the steam ow (see section B).
The ironed garment
turns dark and/or sticks
to the soleplate.
The selected temperature is too high
and has damaged the garment.
Select a suitable temperature for the
material being ironed and clean the
soleplate with a damp cloth.
The soleplate turns
brown.
This is a regular consequence of
continued use over a long period of
time.
Clean the soleplate with a damp cloth.
The appliance makes a
pumping sound.
Water is being pumped into the
steam tank.
The sound will not stop.
This is normal.
If the sound will not stop, do not use the
steam generator and contact an authorised
technical service centre.
Loss of pressure
during ironing.
Steam release button has been
activated for too long a period of
time, that is, it has been pressed too
frequently.
Use the steam release button at intervals.
This improves the ironing result as the
textiles will be steamed, dried and ironed
properly.
Water spots appear
on the garment during
ironing.
May be caused by steam condensed on
the ironing board.
Wipe the textile cover of the ironing board,
and iron any water drops to dry them.

Содержание

en Trouble shooting Problem Possible causes Solution Pilot light 11 flashes Boiler and filter must be rinsed Rinse the filer and the boiler according to the cleaning instructions in this manual see section E The steam generator does not come on There is a connection problem The main power button is not switched on Check the mains cable 6 the plug and the socket Set the main power button 12 to the I position illuminated in red The iron does not heat up The main power button is not switched on The temperature is set to a low position Set the main power button 12 to the I position illuminated in red Set the temperature to the desired position The iron begins to smoke when switched on During first use certain components on the appliance have been lightly greased at the factory and may produce a little smoke when initially heated During subsequent use the soleplate may be soiled This is completely normal and will stop after a short while Clean the soleplate according to the cleaning instructions in this manual Water flows through the holes on the soleplate The steam function is being used before it has reached the correct temperature The water is condensing inside the pipes because steam is being used for the frst time or has not been used for a long time Reduce the steam flow when ironing at low temperatures Point the iron away from the ironing area and press the steam release button until steam is produced Dirt comes out through the soleplate There is a build up of scale or minerals in the steam tank Chemical products or additives have been used Use tap water mixed 50 with distilled or demineralised water To prolong the optimum steam function mix tap water with distilled water 1 1 If the tap water in your district is very hard mix tap water with distilled water 1 2 Clean the soleplate with a damp cloth Never add products to the water The iron does not produce any steam The boiler is not switched on or the water tank is empty The steam regulation is set to the minimum position Set the main power button 12 to the I position illuminated in red and or til the water tank Increase the steam flow see section B The ironed garment turns dark and or sticks to the soleplate The selected temperature is too high and has damaged the garment Select a suitable temperature for the material being ironed and clean the soleplate with a damp cloth The soleplate turns brown This is a regular consequence of continued use over a long period of time Clean the soleplate with a damp cloth The appliance makes a pumping sound Water is being pumped into the steam tank The sound will not stop This is normal If the sound will not stop do not use the steam generator and contact an authorised technical service centre Loss of pressure during ironing Steam release button has been activated for too long a period of time that is it has been pressed too frequently Use the steam release button at intervals This improves the ironing result as the textiles will be steamed dried and ironed properly Water spots appear on the garment during ironing May be caused by steam condensed on the ironing board Wipe the textile cover of the ironing board and iron any water drops to dry them 14

Скачать