Home
Главная
Braun
Утюги
SI 6591
Инструкция по эксплуатации Страница: 10

Braun SI 6591 [10/70] G cleaning the anticalc valve

G Cleaning the anticalc valve

The iron’s anticalc valve is located at the

lower end of the steam button (3). It has

to be decalcified regularly (e.g. when the

steam development is insufficient).

Proceed as follows:

1) Unplug the iron and empty the water tank.

2) Press the steam button so it is lifted.

3) Remove carefully (some water may now

leak from the sole plate).

4) Do not touch the anticalc valve.

5) Immerse in vinegar (not vinegar essence)

or lemon juice until the lime becomes soft.

6) Use a non-metallic brush until all openings

are clean.

7) Rinse under running water.

8) Re-insert the steam button.

9) Press to check the steam on/off function.

Note:

the iron must never be used without

the steam button.

H Decalcifying /anticalc system

When scale particles come out of the steam

vents or when the steam development is

insufficient even after cleaning the anticalc

valve, you should clean the steam chamber

as follows:

1) Make sure the steam button is in its lower

position.

2)–3) Fill water into the tank, connect to the

mains and select the «•••» temperature

setting.

4)–5) Wait until the pilot light turns off.

Unplug the iron.

6)–7) Hold the iron over a sink, then press the

steam button so it is lifted, carefully pull it

up, turn it and rest it in this position.

Caution:

When the steam button is pulled

up, hot water and steam will come out from

the sole plate.

8) Push back the steam button until it catches

in the lower position.

9)–10) Fill water into the tank, connect to the

mains and select the «•••» temperature

setting.

11)–13) When the pilot light goes off, press

the power shot button 4 times to rinse the

iron. Disconnect the iron and wait for the

sole plate to cool off, then clean it as

described above in section «G».

Note:

the iron must never be used without

the steam button.

I Trouble-shooting guide

Problem Remedy

––––––––––––––––––––––––––––––––––––––

Drops Turn the steam regulator

coming out counter-clockwise to

of the steam reduce the steam or

vents press the steam button

to turn the steam off.

Take longer intervals

when pressing the power

shot button.

Select a higher tempera-

ture setting.

No steam Press the steam button

at all so that it is lifted.

Less steam Clean the anticalc valve

develops or (see «G»).

no steam at all

Calcium par- Decalcify the steam

ticles coming chamber (see «H»).

through the

steam vents

––––––––––––––––––––––––––––––––––––––

Subject to change without notice.

This product conforms to the

European Directives EMC 2004/108/

EC and Low Voltage 2006/95/EC.

Please do not dispose of the

product in the household waste

at the end of its useful life. Disposal

can take place at a Braun Service

Centre or at appropriate collection

points provided in your country.

3674350_SI6000_S6-72 Seite 10 Montag, 25. Februar 2008 9:36 09

Содержание

Похожие устройства

G Cleaning the anticalc valve The iron s anticalc valve is located at the lower end of the steam button 3 It has to be decalcified regularly e g when the steam development is insufficient Proceed as follows 1 Unplug the iron and empty the water tank 2 Press the steam button so it is lifted Note the iron must never be used without the steam button I Trouble shooting guide Problem Remedy Drops coming out of the steam vents Turn the steam regulator counter clockwise to reduce the steam or press the steam button to turn the steam off Take longer intervals when pressing the power shot button Select a higher tempera ture setting 3 Remove carefully some water may now leak from the sole plate 4 Do not touch the anticalc valve 5 Immerse in vinegar not vinegar essence or lemon juice until the lime becomes soft 6 Use a non metallic brush until all openings are clean 7 Rinse under running water No steam Press the steam button at all so that it is lifted Less steam develops or no steam at all Clean the anticalc valve see G Calcium par ticles coming through the steam vents Decalcify the steam chamber see H _ 8 Re insert the steam button 9 Press to check the steam on off function Note the iron must never be used without the steam button H Decalcifying anticalc system When scale particles come out of the steam vents or when the steam development is insufficient even after cleaning the anticalc valve you should clean the steam chamber as follows 1 Make sure the steam button is in its lower position 2 3 Fill water into the tank connect to the mains and select the temperature setting 4 5 Wait until the pilot light turns off Unplug the iron 6 7 Hold the iron overasink then press the steam button so it is lifted carefully pull it up turn it and rest it in this position Caution When the steam button is pulled up hot water and steam will come out from the sole plate 8 Push back the steam button until it catches in the lower position 9 10 Fill water into the tank connect to the mains and select the temperature setting 11 13 When the pilot light goes off press the power shot button 4 times to rinse the iron Disconnect the iron and wait for the sole plate to cool off then clean it as described above in section G 10 Subject to change without notice This product conforms to the ff European Directives EMC 2004 108 EC and Low Voltage 2006 95 EC Please do not dispose of the product in the household waste at the end of its useful life Disposal can take place at a Braun Service Centre or at appropriate collection points provided in your country

Скачать