![Makita BDF 460 WAE [9/32] Adjustable depth rod fig 4](/img/pdf.png)
Makita BDF 460 WAE [9/32] Adjustable depth rod fig 4
9
Trickle charge (Maintenance charge)
If you leave the battery cartridge in the charger to prevent spontaneous discharging after full charge, the charger will
switch into its “trickle charge (maintenance charge)” mode and keep the battery cartridge fresh and fully charged.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely discharged.
Always stop tool operation and charge the battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F).
Let a hot battery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months.
NOTE:
• The battery charger is for charging Makita-battery cartridge. Never use it for other purposes or for other manufac-
turer’s batteries.
• When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it
may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the bat-
tery cartridge fully after discharging it completely and recharging a couple of times.
• If you charge a battery cartridge from a just-operated tool or battery cartridge which has been left in a location
exposed to direct sunlight for a long time, the charging light may flash in red color. If this occurs, wait for a while.
Charging will begin after the battery cartridge is cooled by the cooling fan installed in the charger (DC24SA only).
When the temperature on battery is more than approx. 70°C, two charging lights may flash in red color, and when
approx. 50°C – 70°C, one charging light in red color.
• If the charging light flashes alternately in green and red color, charging is not possible. The terminals on the charger
or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged.
• Any of the following conditions indicates damage to the charger and/or battery cartridge. Ask your Makita Authorized
or Factory Service Center to check them.
1) The charging light does not flash (green) when the battery charger is plugged into a power source.
2) The charging light does not light up or flash (red) when the battery is inserted in the charger port.
3) Charging is not completed at even more than two hours after red light comes ON at start of charging.
Side grip (auxiliary handle) (Fig. 3)
Always use the side grip to ensure operating safety.
Install the side grip so that the teeth on the grip fit in
between the protrusions on the tool barrel. Then tighten
the grip by turning clockwise at the desired position. It
may be swung 360° so as to be secured at any position.
Adjustable depth rod (Fig. 4)
The adjustable depth rod is used to drill holes of uniform
depth. Loosen the thumb screw, set to desired position,
then tighten the thumb screw.
Installing or removing driver bit or drill bit
(Fig. 5 & 6)
Important:
Always be sure that the tool is switched off and the bat-
tery cartridge is removed before installing or removing
the bit.
Turn the sleeve counterclockwise to open the chuck jaws.
Place the bit in the chuck as far as it will go. Turn the
sleeve clockwise to tighten the chuck. To remove the bit,
turn the sleeve counterclockwise.
When not using the driver bit, keep it in the bit holders.
Bits 45 mm long can be kept there.
Switch action (Fig. 7)
CAUTION:
Before inserting the battery cartridge into the tool, always
check to see that the switch trigger actuates properly and
returns to the “OFF” position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop.
Reversing switch action (Fig. 8)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation. When the switch lever is in the neutral
position, the switch trigger cannot be pulled.
Speed change (Fig. 9)
To change the speed, first switch off the tool and then
slide the speed change lever to the “II” side for high
speed or “I” side for low speed. Be sure that the speed
change lever is set to the correct position before opera-
tion. Use the right speed for your job.
CAUTION:
• Always set the speed change lever fully to the correct
position. If you operate the tool with the speed change
lever positioned half-way between the “I” side and “II”
side, the tool may be damaged.
• Do not use the speed change lever while the tool is run-
ning. The tool may be damaged.
Содержание
- Bdf460 1
- Indoor use only 4
- Symbole 4
- Symbols 4
- Символы 4
- Achtung 5
- Do not discard batteries into garbage can or the like 5
- Примечание 5
- English 6
- Safety instructions 6
- Additional safety rules for charger battery cartridge 7
- Avoid unintentional starting do not carry the tool with a finger on the switch 17 stay alert watch what you are doing use common sense do not operate the tool when you are tired 18 check damaged parts before further use of the tool a guard or other part that is damaged should be carefully checked to determine that it will operate prop erly and perform its intended function check for alignment of moving parts free running of moving parts breakage of parts mounting and any other condition that may affect its operation a guard or other part that is dam aged should be properly repaired or replaced by an authorized service facility unless other wise indicated in this instruction manual have defective switches replaced by an authorized service facility do not use the tool if the switch does not turn it on and off 19 warning the use of any accessory or attachment other than recommended in this instruction manual may present a risk of personal injury ensure that the battery pack is correct for 7
- Important safety instructions for charger battery cartridge 7
- Additional safety rules for tool 8
- Charging fig 2 8
- Conditioning charge dc24sa only 8
- Cooling system dc24sa only 8
- Installing or removing battery cartridge fig 1 8
- Operating instructions 8
- Save these instructions 8
- Adjustable depth rod fig 4 9
- Installing or removing driver bit or drill bit fig 5 6 9
- Reversing switch action fig 8 9
- Side grip auxiliary handle fig 3 9
- Speed change fig 9 9
- Switch action fig 7 9
- Tips for maintaining maximum battery life 9
- Trickle charge maintenance charge 9
- Adjusting the fastening torque fig 10 10
- Drilling operation 10
- Maintenance 10
- Replacement of carbon brushes fig 12 13 10
- Screwdriving operation fig 11 10
- Ec declaration of conformity 11
- Makita international europe ltd 11
- Noise and vibration 11
- Deutsch 12
- Sicherheitsvorschriften 12
- Wichtige sicherheitshinweise für ladegerät und akku 13
- Bedienungshinweise 14
- Bewahren sie diese hinweise sorgfältig auf 14
- Ein und ausbau des akkus abb 1 14
- Umweltschutz 14
- Zusätzliche sicherheitsregeln für die maschine 14
- Zusätzliche sicherheitsregeln für ladegerät und akku 14
- Anpassungsladung 15
- Erhaltungsladung 15
- Kühlsystem 15
- Laden abb 2 15
- Tips zur erhaltung der maximalen akkulebensdauer 15
- Drehrichtungsumschalter abb 8 16
- Drehzahlumschalter abb 9 16
- Montage und demontage des schraubendreher bzw bohrereinsatzes abb 5 und 6 16
- Schalterfunktion abb 7 16
- Seitengriff zusatzgriff abb 3 16
- Verstellbarer tiefenanschlag abb 4 16
- Bohren 17
- Einstellen des anziehdrehmoments abb 10 17
- Kohlebürsten wechseln abb 12 u 13 17
- Schraubbetrieb abb 11 17
- Wartung 17
- Ce 2003 18
- Ce konformitätserklärung 18
- Geräusch und vibrationsentwicklung 18
- Makita international europe ltd 18
- Dane techniczne 19
- Instrukcje bezpieczeństwa 19
- Polski 19
- Wyjaśnienia dotyczące narzędzia i jego użycia 19
- Dodatkowe zaelcenia dotyczące bezpiecznego posługiwania się ładowarką i wkładką akumulatorową 20
- Ważne zalecenia dotyczące bezpiecznego posługiwania się ładowarką i wkładką akumulatorową 20
- Dodatkowe zasady bezpieczeństwa 21
- Instrukcja obsługi 21
- Przestrzegać niniejszych instrukcji 21
- Wkładanie lub wyjmowanie wkładki akumulatorowej rys 21
- Ładowanie rys 21
- Dc24sa 22
- Podładowywanie ładowanie ciągłe małym prądem 22
- Porady dotyczące zapewnienia maksymalnej żywotności akumulatora 22
- Układ chłodzenia 22
- Ładowanie optymalne 22
- Działanie przełącznika rys 7 23
- Działanie przełącznika zmiany kierunku rys 8 23
- Operacje wkręcania rys 1 23
- Regulowalny miernik głębokości rys 4 23
- Uchwyt boczny pomocniczy rys 3 23
- Ustawianie momentu dokręcania rys 10 23
- Zakładanie lub wyjmowanie końcówki śrubokrętowej lub wiertła rys 5 i 6 23
- Zmiana prędkości rys 9 23
- Ce 2003 24
- Konserwacja uwaga 24
- Makita international europe ltd 24
- Operacje wiercenia 24
- Szumy i drgania 24
- Ue deklaracja zgodności 24
- Wymiana szczoteczek węglowych rys 12 i 13 24
- Инструкции по мерам безопасности 25
- Русский язык 25
- Технические характеристики 25
- Важные инструкции по безопасности для зарядного устройства и батареиного картриджа 26
- Дополнительные правила безопасности 27
- Дополнительные правила безопасности для зарядного устройства и батарейного картриджа 27
- Сохраните эти инструкции 27
- Инструкция по эксплуатации 28
- Боковой захват дополнительная ручка рис 3 29
- Компенсационная зарядка эксплуатационная зарядка 29
- Регулируемый стержень глубины рис 4 29
- Советы по поддержанию максимального срока службы батареи 29
- Установка или удаление завинчивающего сверла или сверла дрели рис 5 и 6 29
- Действие обратного переключения рис 8 30
- Действия при переключении рис 7 30
- Операция завинчивания рис 1 30
- Переключение скорости рис 9 30
- Регуляровка крепящего момента рис 10 30
- Ce 2003 31
- Makita international europe ltd michigan drive tongwell milton keynes bucks mk15 8jd england 31
- Ес декларация соответствия 31
- Замена угольных щеток рис 12 и 13 31
- Обслуживание 31
- Операция сверления 31
- Шум и вибрация 31
Похожие устройства
- Энкор Корвет-67 10267 Инструкция по эксплуатации
- Vitek VT-1900 Инструкция по эксплуатации
- Энкор Корвет-23 10223 Инструкция по эксплуатации
- Makita 6339 DWFE Инструкция по эксплуатации
- Gorenje HB400W Инструкция по эксплуатации
- Scarlett SC-370 Инструкция по эксплуатации
- Nokia С1-02 Black Инструкция по эксплуатации
- Polaris VEGA P 3.5 Инструкция по эксплуатации
- Gorenje HB804E Инструкция по эксплуатации
- Makita 6349 DWDE Инструкция по эксплуатации
- Scarlett SC-179 Инструкция по эксплуатации
- Nokia 2700C Black Инструкция по эксплуатации
- Makita 6349 DWFE Инструкция по эксплуатации
- Kospel EPO.D/G-4 AMICUS Инструкция по эксплуатации
- Gorenje HB802W Инструкция по эксплуатации
- Scarlett SC-178 Инструкция по эксплуатации
- M-Audio AXIOM 61 Инструкция по эксплуатации
- Nokia 1616{C-2} Black Инструкция по эксплуатации
- Gorenje HB451W Инструкция по эксплуатации
- Polaris VEGA S 5.5 Инструкция по эксплуатации