Главная
Skipped breadcrumb items
esp05-200 t
Инструкция по эксплуатации Страница: 16

Главная
DWT
esp05-200 t
Инструкция по эксплуатации Страница: 16

DWT esp05-200 t — power Tool Spray Safety Guidelines - User Instructions [16/80]

Превью страниц Страница 16 / 80

for viewing only

English

26 Drain hole Please note! The use of dust masks or respirators

27 Air filter *

will not assure the required effect - you may suffer

severe intoxication.

Smoking during spraying inflammable materials is

* Optional extra

strictly prohibited.

While working, do not direct the stream of the

Not all of the accessories illustrated or described

sprayed material onto yourself, other individuals, or

are included as standard delivery.

animals. The stream may pierce your skin (even

through gloves) and inject the sprayed material - in such

DWT

a case seek medical attention immediately.

power tool designation

Please bear in mind that during working the

surrounding air fills with "mist" consisting of fine

This power tool is designed for spraying and applying

droplets of the sprayed material that subsequently

liquid materials on a treated surface. It allows the user to

settles on surrounding surfaces. The surfaces on

apply paints, varnishes, primers, preservatives,

which the "mist" precipitation is unwanted should be

protective and disinfectant materials, as well as to spray

covered. When working outside, the "mist" is

water for wetting surfaces.

exposed to wind, which may lead to negative

consequences (unwanted painting of objects,

Safety guidelines during

c a u s in g h a r m t o h e a l t h , e n v i r o n m e n t a l

power tool operation

contamination).

Do not switch on the power tool if there is no liquid in

Before commencing operation

the reservoir - dry running causes rapid wear of power

tool components.

Spraying inflammable materials increases the risk of fire

or explosion, so please follow all the required precautions

After finishing operation

and ensure that there are fire-extinguishing means on site.

After handling inflammable materials (for example,

The power tool must be cleaned after each use as

after mixing or thinning paint or after cleaning any parts

described below. Failure to clean or improper cleaning

of the power tool) remove all used containers and the

may cause breakage of the power tool, which will void

cloth, as they may cause fire.

the warranty.

Make sure that the area where the works will take

Dispose of the sprayed material residues (paint

place is properly ventilated - gases or vapors generated

materials, solvents, etc.) in strict compliance with the

during work may be harmful to your health and increase

manufacturer's instructions.

the risk of fire or explosion.

Do not work near the sources of open fire or sparks,

Installation and regulation

hot objects, engines.

of power tool elements

Do not spray materials having a flash point below 21°С -

this increases the risk of fire or explosion.

Before carrying out any works on the power tool it

Prior to spraying the material, carefully read

must be disconnected from the mains.

manufacturer's instructions in order to undertake the

appropriate safety measures.

Do not draw up the fastening elements

Do not spray unknown materials or materials with

too tight to avoid damaging the thread.

unknown dangers.

Do not spray any materials that can damage the

Mounting / dismounting / setting-up of

power tool; if the power tool breaks as a result, your

some elements is the same for all power

warranty will be voided. Spraying acids, alkalis,

tool models, in this case specific models

materials containing abrasive particles, materials

are not indicated in the illustration.

containing lead, liquid glass, excessively thick

materials, and other materials that are difficult to spray

Reservoir connection / disconnection (see fig. 1-2)

or to form drops is strictly prohibited.

Install the base unit 11 onto the horizontal vibration-

Connect / disconnect reservoir 5 as shown on figures 1-2.

free surface. The air sucked through the holes of the

cover 8 must be clean; therefore, do not use the base

[ESP05-200 T]

unit 11 in a dusty environment; also make sure that the

cover 8 is not covered by anything (only for model

Prior to connecting reservoir 5, turn tube 18

ESP05-200 T).

(see fig. 2.2) into the position allowing maximum

use up of the material. It depends on where the

During operation

spray gun will be tilted during operation (see

fig. 2.3-2.4).

Loosen the lock nut and unscrew the nut .

Use personal protective equipment - special clothing,

20 19

Turn the tube to the required position.

glasses, gloves, and closed shoes.

Screw the nut and secure it by tightening the lock

Use special masks intended for the protection of

nut .

respiratory system from harmful substance vapors.

DWT esp05-200 t — power Tool Spray Safety Guidelines - User Instructions [16/80]

Содержание

Похожие устройства