Главная
Skipped breadcrumb items
esp05-200 t
Инструкция по эксплуатации Страница: 17

Главная
DWT
esp05-200 t
Инструкция по эксплуатации Страница: 17

DWT esp05-200 t — инструкция по использованию гибкого распылителя и его настройке [17/80]

Превью страниц Страница 17 / 80

for viewing only

English

F l e x i b l e e x t e n s i o n h o s e c o n n e c t i o n / To decrease volume of the sprayed material, rotate

disconnection (see fig. 3)

regulator 6 as shown in figure 5 (while spraying

material). Note that the excessive decrease of the

[ESP01-250]

sprayed material volume leads to poorer results of

treatment (insufficient impregnation, too thin a paint

Flexible extension hose 17 allows spraying

layer, etc.).

material onto horizontal surfaces as well as in hard-

To increase volume of the sprayed material, rotate

to-reach places (for example, when painting heating

regulator 6 as shown in figure 5 (while spraying

radiators).

material). Note that an excessive increase of the

Unscrew nozzle 1 (see fig. 3).

sprayed material volume results in drips on the treated

Screw flexible extension hose 17 on, then bend it into

surface and overconsumption of the sprayed material.

the required position.

In order to disconnect, perform these steps in reverse

Sprayed stream shape regulation (see fig. 6)

order.

[ESP05-200 T]

Air hose connection / disconnection (see fig. 4)

You can adjust the shape of the sprayed stream by

[ESP05-200 T]

rotating air cap 2 depending on the direction of the spray

gun's movement (see fig. 6.2-6.4).

Connect the air hose 7 to the base unit 11. Insert the

tip 22 into the opening 21 after aligning the protrusions

Loosen coupling nut 3 (see fig. 6.1).

on the tip 22 with the grooves in the hole 21. Rotate the

Turn air cap 2 to the desired position (see fig. 6.2-6.4).

tip 22 as shown on figure 4.1.

Tighten coupling nut 3.

Connect the air hose 7 to the spray gun or the purge

nozzle 15. Place the tip 23 on the shank of the

Spray gun holder (see fig. 7)

accessory by pre-aligning the grooves in the tip 23 with

the protrusions on the accessory. Rotate the tip 23 as

[ESP05-200 T]

shown on figure 4.2.

In order to disconnect, perform these steps in reverse

The holder 10 is designed to secure the spray gun

order.

during the movement of the power tool or during the

breaks in the work process.

Initial operating

Install the holder 10 as shown on figure 7.1 (the

of the power tool

fixtures on the lugs must click shut). You can install the

holder 10 from different sides of the base unit 11.

Always use the correct supply voltage: the power

To remove the holder 10, slightly pull the lugs and

supply voltage must match the information quoted on

remove the holder as shown on figure 7.2.

the power tool identification plate.

Switching the power

Carrying belt (see fig. 7)

tool on / off

[ESP05-200 T]

[ESP01-250]

To facilitate the transportation, as well as to provide

Switching on:

greater portability during the work, use the carrying

Press and hold button 4.

belt 14. Connect the belt 14 to the base unit 11 (see

Switching off:

fig. 7.3). If necessary, adjust the length of the belt 14

Release button 4.

so that make carrying the power tool easier.

[ESP05-200 T]

Recommendations

on the power tool operation

Switching on:

Press and release on / off switch 9. In order to start

Measurement of sprayed material viscosity (see fig. 8)

spraying material, press and hold button 4 on the spray

gun.

Switching off:

The viscosity of the sprayed material should not exceed

Release button 4, then press and release on / off switch 9.

the maximum allowable value (see technical data

table). Thicker materials should be diluted. Please

Design features

note! Always use an appropriate solvent, otherwise

of the power tool

the lumps will form that will result in clogging the

power tool.

Sprayed material volume regulation (see fig. 5)

Measure the viscosity using measuring funnel 12. The

temperature of the compound should be 20-22°С.

Using regulator 6, you can adjust the volume of the

Stir the compound thoroughly, immerse measuring

spayed material in order to get the desired work result.

funnel 12 into it, and wait until it fills (see fig. 8).

DWT esp05-200 t — инструкция по использованию гибкого распылителя и его настройке [17/80]

Содержание

Похожие устройства