![Supermicro sys-5018d-mtrf Инструкция по эксплуатации онлайн [80/122] 187892](/icons/site-icon-64.png){kind=icon}
Supermicro sys-5018d-mtrf Инструкция по эксплуатации онлайн [80/122] 187892
Превью страниц
Страница 80 /
122
![Supermicro sys-5018d-mtrf Инструкция по эксплуатации онлайн [80/122] 187892](/views2/1225207/page80/bg50.png)
6-6
SUPERSERVER 5018D-MTF/5018D-MTRF User's Manual
Figure 6-4. Mounting a Drive in a Carrier
Figure 6-5. Removing a Drive from the Server
Warning: Enterprise level hard disk drives are recommended for use in Supermicro
chassis and servers. For information on recommended HDDs, visit the Supermicro Web
site at http://www.supermicro.com/products/nfo/les/storage/SAS-1-CompList-110909.
pdf
Содержание
280- Warning handling of lead solder materials used in this product may expose you to lead a chemical known to the state of california to cause birth defects and other repro ductive harm
- Printed in the united states of america
- Manual revision 1 c release date march 18 2015
- About this manual
- Preface
- Manual organization
- Chapter 4 standardized warning statements
- Chapter 3 system interface
- Chapter 2 server installation
- Chapter 1 introduction
- Chapter 7 bios
- Chapter 6 advanced chassis setup
- Chapter 5 advanced motherboard setup
- Appendix b system specifications
- Appendix a bios error beep codes
- Table of contents
- Chapter 3 system interface
- Chapter 2 server installation
- Chapter 1 introduction
- Chapter 4 standardized warning statements for ac systems
- Chapter 5 advanced motherboard setup
- Chapter 7 bios
- Chapter 6 advanced chassis setup
- Appendix b system specifications
- Appendix a bios error beep codes
- Introduction
- Chapter 1
- 1 overview
- Serial ata
- Processors
- Memory
- I o ports
- 2 motherboard features
- Cooling system
- Control panel
- 3 server chassis features
- System power
- Sata subsystem
- Usb usb
- Up to 1600
- System power
- System block diagram
- Pch lynx point c222 c224
- Note two chipsets are shown the c224 applies to the x10slm f
- Note this is a general block diagram please see chapter 5 for details
- Front panel
- Figure 1 1 intel c224 chipset
- Erver 5018d mtf 5018d mtrf user s manual
- Debug card
- Ctrl fan speed
- 4 contacting supermicro
- Server installation
- 1 overview
- Choosing a setup location
- Chapter 2
- 3 preparing for setup
- 2 unpacking the system
- Server precautions
- Rack precautions
- 4 warnings and precautions
- Reliable ground
- Reduced airflow
- Rack mounting considerations
- Mechanical loading
- Circuit overloading
- Ambient operating temperature
- Identifying the sections of the rack rails
- 5 installing the system into a rack
- Installing the rear inner rails
- Installing the rack rails
- Installing the server into the rack
- Installing the server into a telco rack
- System interface
- Chapter 3
- 2 control panel buttons
- 1 overview
- Overheat fan fail
- 3 control panel leds
- 4 hard drive carrier leds
- Warning definition
- Standardized warning statements for ac systems
- Chapter 4
- 1 about standardized warning statements
- ןונקת תורהצהאהרהז ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע היישעתה ינקת יפ לע תורהז הלבח ה וא תולאש שיו הדימב תירשפא תיזיפי יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט ורקימרפוס לש תינכט תאה םיביכר אורקל שי ורקימרפוס יזראמב םיביכרה תרדגה וא תנקתה ינפל ואולמב חפסנה תא
- ف ك ا ىأ يكو ةلاح ف ببستت ةباصا ة ذسج زهزلا اذه ع زطخ ز ذحت ىأ لبق يأ ىلع لوعت تاذعه كنلع ىلع ي يع ةوجا لا زطاخولاب زئاوذلا ة ئابزهكلا كوة ارد ىلع ي راوولابتاس ة ئاقىلا ل ع وعىقو يأثداىح نقر مذختسا ىا بلا صىص ولا ة اه ف ز ذحت لك رىثعلل اهتوجزت
- لا تاداشرإ رقابيكرت ليصوت لبق ىلإ ماظنلا ةقاطلل ردصم
- אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ
- Installation instructions
- يئاقول
- ىلع
- متيتلا
- Vdc 20
- Circuit breaker
- A 250vd
- Power disconnection warning
- مصف بجي واظننا عيمج نمرداصم تقاطنا تنازإو ءابرهكنا كهس نم ةدحو دادما تقاطنا مبق ىنإ لىصىنا تيهخادنا قطانمنا نمكيهه تنازإ وأ جيبثتن ثانىكم زاهجلا
- ילמשח קותינ ינפמ הרהזא
- הרהזא למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת םיביכר
- הרהזא שר דבלב ךמסומ תווצתא ףילחהל ןיקתהל יא דויצה רובע תוריש תתל וא דויצה
- Equipment installation
- هيبردملاو و بيكزتللادبتسا وأ ةمدخ ساهجلا اذه حمسي نأ بجي طقف هيلهؤملا هيفظىملل
- Restricted area
- صيصخت ةذحىنا هذه ف اهب كرتن قطانم ةروظحم مت صىنا نكم نإ لى تقطنم ةروظحم طقف واذختسا للاخ نم تصاخ ةادأ وأ أ لان يرخأ ته سو املأم حاتفمو مفق
- תלבגומ השיג םע רוזא הרהזא תרזעב תנתינ השיגה השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי דכו לוענמ חתפמ דבלב החטבא ילכ
- Battery handling
- رطخ كانه نم لاذبحسا ةلاح يف راجفنا ةيراطبلا ةحيحص ريغ ةقيرطب ليلعف ةيراطبلا لاذبحسا طقف عىنلا سفنب اهلداعي ام وأ اممثصوأ ةعنصملا ةمرشلا هب تايراطبلا نم صلخج ل اقفو ةلمعحسملاةعناصلا ةمرشلا تاميلعح
- הרהזא תנכס תמייקץוציפ הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ תוללוסה קוליס תושמושמה עצבל שי ןרציה תוארוה יפל
- חיה תאי הד
- דחא קפסמ רתוי םייק םא הרהזא קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שי ןקורל תנמ לע םירוביחה לכ
- Redundant power supplies
- دق اذهل نوكي لازاهج تلااصتا ةدع تادحوب ةقاطلا دادما ةلازإ بجي تلااصتلاا ةفاك لسعل لاةدحو نع ءابرهكلا
- Backplane voltage
- كانه زطخ هم يئابزهكلا رايتلا ىلع ةدىجىملا ةقاطلاوأ ةحىللا نىكي امدنعماظنلا لمعي دنع ارذح هك ةمدخ ساهجلا اذه
- ירוחאה לנפב חתמ זא הרה ךלהמב רהזיהל שי תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק הדובעה
- Comply with local and national electrical codes
- Product disposal
- تادعملا بيكرت ةيئابرهكلا لل لثتمي نأ بجي هيواىقةيىطىلاو ةيلحملا ةقلعتملا ءابرهكلاب
- יצראה למשחה יקוח םואית הרהזא תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה
- يئاهنلا صلختلا نم جتنملا اذه هعم لماعتلا يغبني ل اقفو عيمجةينطىلا حئاىللاو نيناىقلا دنع
- רצומה קוליס הרהזא ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס הנידמה יקוח
- Hot swap fan warning
- هكممنا هم حوارمنا نأ لاست لا ةنازإ دنعرودت ةهتك ةحورمنا مكيهنا هم بجي ءاقبإ هكممنا هم حوارمنا نأ لاست لا ةنازإ دنعرودت ةهتك ةحورمنا مكيهنا هم بجي ءاقبإ
- عباصلأا ويغاربنا تاكفم ءايشلأا هم اهريغو اديعب هع تاحتفنا يف ةهتك ةحورمنا
- הרהזא יקלח תא םיריסמ רשאכ שי םידבוע ןיידע םיררוואמהו ןכתי זראמהמ ררוואמה קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה תא חוטב קחרמ
- Power cable and ac adapter
- Precautions
- Chapter 5
- Advanced motherboard setup
- 1 handling the motherboard
- Installing an lga1150 processor
- 2 processor and heatsink installation
- Cpu pin 1
- Removing the heatsink
- Installing a passive cpu heatsink
- Figure 5 2 removing the heatsink
- Figure 5 1 installing the heatsink
- Chapter 5 advanced motherboard setup
- Connecting the control panel
- Connecting power cables
- Connecting data cables
- 3 connecting cables
- 4 i o ports
- Caution
- 5 installing memory
- Possible system memory allocation availability
- Erver 5018d mtf 5018d mtrf user s manual
- 6 adding pci cards
- 7 motherboard details
- X10slm f quick reference
- T sgpio2
- T sgpio1
- Bmc fw
- The power led connection is located on pins 15 and 16 of jf1 refer to the table on the right for pin definitions
- The non maskable interrupt button header is located on pins 19 and 20 of jf1 refer to the table on the right for pin definitions
- The hdd led connections are located on pins 13 and 14 of jf1 attach a cable here to indicate hdd activity see the table on the right for pin definitions
- The 24 pin main power connector jpw1 is used to provide power to the motherboard the 8 pin cpu power connector jpw2 is also required for the processor these power connectors meet the ssi eps 12v specification see the tables on the right for pin definitions
- Power led
- Power connectors
- Nmi button
- Hdd led
- Erver 5018d mtf 5018d mtrf user s manual
- 8 connector definitions
- Connect an led cable to the front uid and oh fan fail connections on pins 7 and 8 of jf1 to display uid unit id sig nals or to provide advanced warnings for chassis overheat fan failure refer to the table on the right for pin definitions
- Chapter 5 advanced motherboard setup
- The reset button connection is located on pins 3 and 4 of jf1 attach it to a the hardware reset button on the computer case refer to the table on the right for pin definitions
- The power fail led connection is located on pins 5 and 6 of jf1 refer to the table on the right for pin definitions
- The nic network interface controller led connection for lan port 1 is located on pins 11 and 12 of jf1 and the led connection for lan port 2 is on pins 9 and 10 attach nic led cables to nic1 led and nic2 led to display network activities for lan 1 and lan2 refer to the table on the right for pin definitions
- The com1 port is located on the i o backpanel com2 is a header located on the the motherboard see the table
- Serial ports
- Reset button
- Power fail led
- Overheat oh fan fail front uid led
- On the right for pin definitions
- Nic1 nic2 lan1 lan2
- Universal serial bus usb
- The power button connection is located on pins 1 and 2 of jf1 momentarily contacting both pins will power on off the system this button can also be config ured to function as a suspend button see bios setup to turn off the power in the suspend mode press the button for at least 4 seconds refer to the table on the right for pin definitions
- Power button
- Four universal serial bus 2 ports usb 4 5 6 7 are located on the i o back panel of the x10slm f in addition four usb 3 headers usb 0 1 2 3 and two additional usb 2 headers usb 8 9 are located on the x10slm f see the tables below for pin definitions
- Erver 5018d mtf 5018d mtrf user s manual
- A chassis intrusion header is located at jl1 on the motherboard attach the ap propriate cable from the chassis to inform you of a chassis intrusion when the chas sis is opened
- The x10slm f has five fan headers fan1 fan4 and fana these are 4 pin fan headers and work with ipmi to moni tor and change fan speed as required based on the system temperature refer to the table on the right for pin definitions
- The internal buzzer sp1 can be used to provide audible indications for various beep codes see the table on the right for pin definitions
- Power led speaker
- On the jd1 header pins 1 3 are used for power led indication and pins 4 7 are for the speaker see the tables on the right
- Internal buzzer sp1
- For pin definitions please note that the speaker connector pins 4 7 are used with an external speaker if you wish to use the onboard speaker you should close pins 6 7 with a jumper
- Fan headers
- Chassis intrusion
- Chapter 5 advanced motherboard setup
- System management bus
- Power supply
- Erver 5018d mtf 5018d mtrf user s manual
- C on the motherboard this connector monitors the status of the power supply fan and system tempera ture see the table on the right for pin definitions
- C connector is located at jp
- C connector
- A system management bus header for the ipmi slot is located at ipmb con nect the appropriate cable here to use the ipmb i2c connection on your system
- Wake on lan
- Trusted platform module header
- This header is used to connect a trusted platform module tpm available sepa rately from a third party vendor a tpm is a security device that allows encryption and authentication of hard drives disal lowing access if the tpm associated with it is not installed in the system see the table on the right for pin definitions
- The wake on lan header is located at jstby1 on the motherboard see the table on the right for pin definitions you must also have a lan card with a wake on lan connector and cable to use this feature
- The power supply
- Two t sgpio serial link general pur
- The disk on module dom power con nector located at jsd1 provides 5v gen1 gen power to a solid state dom storage device connected to one of the sata ports see the table on the right for pin definitions
- T sgpio 1 2 3 sgpio 1 2 headers
- Pose input output headers are provided on the motherboard these headers are used to communicate with the enclosure management chip in the system see the table on the right for pin definitions
- Dom pwr connector
- Chapter 5 advanced motherboard setup
- 9 jumper settings
- 10 onboard indicators
- Four sata 3 and two sata 2 ports are included on the motherboard see the table on the right for pin definitions for the onboard sata ports
- Erver 5018d mtf 5018d mtrf user s manual
- 11 sata drive connections
- Sata ports
- 12 installing software
- Superdoctor 5
- 13 onboard battery
- Precautions
- Chapter 6
- Advanced chassis setup
- 1 static sensitive devices
- 3 accessing the system
- 2 control panel
- System fan failure
- 4 system fans
- Accessing the drive bays
- 5 drive bay installation removal
- Sata drive installation
- Sata backplane
- Dvd rom drive installation
- D mtf power
- 6 power supply
- D mtrf power
- Starting bios setup utility
- How to change the configuration data
- Chapter 7
- 1 introduction
- How to start the setup utility
- 2 main setup
- Boot feature
- 3 advanced setup configurations
- Power configuration
- Cpu configuration
- Pci e configuration
- Chipset configuration
- System agent sa configuration
- Memory configuration
- Pch io configuration
- Sata configuration
- Pcie pci pnp configuration
- Intel server platform services configuration
- Acpi settings
- Super io configuration
- Console redirection settings
- Console redirection settings for ems
- Change smbios event log settings
- 4 event logs
- View smbios event log
- The following ipmi information will be displayed
- Bmc network configuration
- 5 boot settings
- 6 security settings
- 7 save exit
- Bios error beep codes
- Appendix a
- System specifications
- Sata drive bays
- Sata controller
- Processors
- Motherboard
- Memory capacity
- Expansion slots
- Chipset
- Appendix b
- Power supply
- Operating environment
- Chassis
- Weight
- System input requirements
- System cooling
- Regulatory compliance
Похожие устройства
-
Supermicro SYS-7047GR-TRF, X9DRG-QF C602 Dual Xeon Socket2011 1866/1600/1333/1066/800MHz, up to 192GB DDR3 ECC Reg, 10xSATA, 1620WИнструкция по эксплуатации -
Supermicro SYS-7048R-TR, X10DRi C612 Dual Xeon Socket2011-3 2133/1866/1600MHz, up to 1TB DDR4 ECC Reg, 8xSATA3, 920W (1+1)Инструкция по эксплуатации -
Supermicro SYS-7048R-TRT, X10DRi-T C612 Dual Xeon Socket2011-3 2133/1866/1600MHz, up to 1TB DDR4 ECC Reg, 8xSATA3, 920W (1+1)Инструкция по эксплуатации -
Supermicro SYS-7047R-TRF, X9DRi-F C602 Dual Xeon Socket2011, 800-1600MHz, up to 512MB DDR3 ECC Reg, 8xSATA3, 920W (1+1)Инструкция по эксплуатации -
Supermicro SYS-5018R-МRИнструкция по эксплуатации -
Supermicro SYS-1028R-WC1RTИнструкция по эксплуатации -
Supermicro SYS-1028R-WC1RИнструкция по эксплуатации
-
Supermicro SYS-1018GR-TИнструкция по эксплуатации -
Supermicro SYS-5018A-TN4Инструкция по эксплуатации -
Supermicro SYS-5019S-MN4Инструкция по эксплуатации -
Supermicro SYS-6028R-TRTИнструкция по эксплуатации -
Supermicro sys-6028r-trИнструкция по эксплуатации