Home
Главная
TSC
Принтер Штрих-Кодов
TTP-384M
Инструкция по эксплуатации Страница: 1

TSC TTP-384M Инструкция по эксплуатации онлайн

USER’S

MANUAL

TTP-384M

THERMAL TRANSFER / DIRECT THERMAL

BAR CODE PRINTER

Содержание

Manual 1
Thermal transfer direct thermal bar code printer 1
Ttp 384m 1
User s 1
Contents 2
Compliances 4
Introduction 4
Product introduction 4
Beachten sie beim anschluß ans stromnetz die anschlußwerte 8 dieses gerät kann bis zu einer außentemperatur von maximal 40 betrieben 5
Das gerät ist vor feuchtigkeit zu schűtzen 6 bei der aufstellung des gerätes ist auf sicheren stand zu achten ein kippen oder 5
Die netzanschluß steckdose soll nahe dem gerät angebracht und leicht zugänglich 5
Fallen könnte beschädigungen hervorrufen 5
Flüssig oder aerosolreiniger am besten eignet sich ein angefeuchtetes tuch zur reinigung 5
Iec60950 1 2001 en 60950 1 a11 2004 wichtige sicherheits hinweise 1 bitte lesen sie diese hinweis sorgfältig durch 2 heben sie diese anleitung fűr den späteren gebrauch auf 3 vor jedem reinigen ist das gerät vom stromentz zu trennen verwenden sie keine 5
Werden 5
在产品的使用手册上有以下声明此为 a 级产品在生活环境中该产品可能会造成无线电干扰在这种情况下可能需要用户对干扰采取切实可行的措施 5
Operations overview 7
Unpacking and inspection 7
Front view 8
Printer overview 8
Interior view 9
6 sd card slot 7 ethernet interface 8 ps 2 interface 9 power switch 10
Fan fold paper entrance chute 1 fan fold paper entrance chute 2 centronics interface 3 usb interface 10
Rear view 10
Rs 232c interface 5 power jack socket 10
Front panel display 12
Led indicators 12
Operator controls 12
Front panel keys 13
Setting up the printer 13
Loading ribbon 14
Loading media 17
Main menu overview 21
Menu function 21
Notice ethernet function is available on the lcd display when ethernet card is installed 21
Notice ethernet function is available on the lcd display when ethernet card is installed 22
Setup menu overview 22
Printer setup 23
Calibration 3 calibration this option is used to set the media sensor type and calibrate the selected sensor we recommend to calibrate the sensor before printing when changing the media 30
Sensor 30
Status this function is available to check the printer s sensor status when enter the status option you will see following message 30
A 3 pre printed 32
Sensor sensitivity it can to get the sensor sensitivity accurately 32
This function can set the paper length and gap size before auto calibrate the 32
When enter pre printed option you will see following message please complete there steps 32
B 1 automatic 34
B 2 manual 34
B bline mode 34
Button to enter the black mark sensor calibration mode 34
Buttons to scroll the cursor to the sensor type press 34
In case automatic sensor calibration cannot apply to the media please use manual function to calibrate the bline sensor manually 34
Press the 34
Printer will feed the black mark label to calibrate the sensor sensitivity automatically when calibration process is completed the lcd screen will return to the previous menu 34
When enter manual option you will see following message please complete there steps 34
When enter the automatic option you will see following message and 34
B 3 pre printed 35
This function can set the paper length and gap size before auto calibrate the sensor sensitivity it can to get the sensor sensitivity accurately 35
When enter pre printed option you will see following message please complete there steps 35
Button to enter the black mark sensor calibration mode 37
Buttons to scroll the cursor to the sensor type press 37
C 1 automatic 37
C 2 manual 37
C cont mode 37
In case automatic sensor calibration cannot apply to the media please use manual function to calibrate the sensor manually 37
Press the 37
Printer will calibrate the sensor sensitivity automatically when calibration process is completed the lcd screen will return to the previous menu 37
When enter manual option you will see following message please complete there steps 37
When enter the automatic option you will see following message and 37
Serial comm 38
Ethernet 42
Avail memory 45
Button 45
Card card 45
Dram dram 45
Exit exit 45
File list 45
File list avail memory del all files 45
File manager 45
Flash flash 45
This feature is used to check the printer available memory and file list 45
To delete the file please follow the order to press the 45
To run the file bas please follow the order to press the 45
Use this menu to show available memory space 45
Use this menu to show delete and run bas the files saved in the printer dram flash card memory to show the files 45
Button to delete all files in the device 46
Del all files 46
To cancel deleting files and go back to previous menu 46
Use this menu to delete all files press 46
Diagnostics 47
Print config 47
Ascii data 50
Captures the data from the communications port and prints out the data received by 50
Diagnostics 2 4 printing dump mode 50
Dump mode 50
Hexdecimal data related to 50
Left column of ascii data 50
Note 1 dump mode requires 4 wide paper width 2 turn off on the power to resume printer for normal printing 3 press feed button to back to the previous menu 50
Printer in the dump mode all characters will be printed in 2 columns as following the left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters it allows users or engineers to verify and debug the program 50
Pritn config 1 1 50
Rotate cutter 50
Button to select this option press 51
Buttons to scroll the curser to desire language and press 51
In case paper is jammed in the cutter this feature can rotate the cutter blade forward or reverse direction which is helpful to remove the jammed paper easily from the cutter 51
Key to cancel the setting and 51
Language 51
Return to the previous menu the default language setting is english 51
Rotate cutter 51
This option is used to setup the language on lcd display press 51
Initialization 52
Service 52
Bline sensor 53
Ip address dhcp 53
Language english 53
Mileage info 53
Sensitivity 53
Use this option to check the printed mileage displayed in meter 53
Will be reset need to re calibrate the gap 53
Diagnostic tool 54
Start the diagnostic tool 54
Calibrate sensor ethernet setup rtc setup 55
Printer functio 55
Printer function calibrate sensor ethernet setup rtc setup 55
Select the pc interface connected with bar code printer 1 select the pc interface connected with bar code printer 2 click the function button to setting 3 the detail functions in the printer function group are listed as below 55
Setting ethernet by diagnostic utility 56
Using usb interface to setup ethernet interface 56
Using rs 232 interface to setup ethernet interface 57
Using ethernet interface to setup ethernet interface 58
Common problems 60
The following guide lists the most common problems that may be encountered when operating this bar code printer if the printer still does not function after all suggested solutions have been invoked please contact the customer service department of your purchased reseller or distributor for assistance 60
Troubleshooting 60
Mechanism fine adjustment to avoid ribbon wrinkles 64
Maintenance 66
Date content editor 68
Revise history 68

TSC TTP-384M Инструкция по эксплуатации онлайн

Содержание

Похожие устройства