DWT SBM-1050 DT [21/176] English
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

DWT SBM-1050 DT [21/176] English

DWT SBM-1050 DT [21/176] English
Impact drilling
Start the power tool, wait until the engine gains its
maximum speed and only after that smoothly bring
During the impact drilling, the result does not depend on
rubber sanding plate 22 or 26 to the surface processed.
the pressure applied to the power tool - this is caused
Holding the power tool at an angle of 10° to 15°
due to the peculiarities in the impact mechanism design.
relating to the surface processed (see picture 17) is
That is why you should not apply excessive pressure to
recommended. If this angle is less than recommended,
the power tool - it can jam the drill and overload the
it will make controlling the power tool more difficult. If this
engine.
angle is more than recommended, the processing
quality will decrease and hollows will be left on the billet
surface.
Drilling in stationary mode
Make crossing movements by applying moderate
Stand 31 creates the possibility for the stationary
pressure to the power tool. Excessive pressure will not
bring better results but it will overload the engine.
mounting of the power tool (see picture 15). The
Sanding with circular movements will leave spiral traces
application of stand 31 increases the accuracy of drilling
and provides greater safety during the implementation
on the surface processed.
of works.
Do not detain the power tool in one place - it will lead
to the formation of a hollow.
One can find recommendations on mounting
operations, the correct usage and order of works in the
When processing wooden surfaces start with sanding
instructions for stand 31.
with sanding discs of a coarser grit and finish with
sanding discs of a finer grit. It will speed up the
implementation of works and allow a smoother surface
Stirring various substances
to be achieved.
[BM-1050 DL]
Prior to processing profile metallic surfaces (tubes,
automobile body parts, etc.), remove any remnants of oil
Do not process explosive substances (for
from them with incombustible chemicals.
example, highly inflammable solvents)
and materials with ignition temperature of
Sanding with leaf sanding disc
lower than 21°С. Study the manufacturer's
Sanding with this method allows profile curved surfaces
instructions for such kind of materials carefully and
to be processed and this is characterized with lesser
stick to them.
noise and heating compared to sanding with the rubber
sanding plate. The application of leaf sanding discs with
The selection of stirring paddle 19 type depends on
various grits allows surfaces with various roughness to
the type of substances stirred. Use stirring paddles with
be achieved, and the operation life of leaf sanding discs
left-hand blade spinning for low-viscosity substances
is much longer than that of sanding discs.
(dispersed paints, lacquers, sealing compounds, liquid
cement solution). Use stirring paddles with right-hand
Install leaf sanding disc 28 as described above.
blade spinning for high-viscosity substances (ready-
Switch on the power tool, wait until the engine gains
made plastering solution, concrete, putty, polymeric
its maximum speed and only after that smoothly bring
resins) (see picture 16).
leaf sanding disc 28 to the billet surface.
Always use additional handle 4, as it makes the
Holding the power tool concerning the surface
implementation of works more convenient and
processed as shown on picture 17 is recommended.
increases the degree of control over the power tool.
Recommendations concerning the implementation of
Fix the container with the mixture stirred carefully
works with leaf sanding disc 28 are similar to those as
during the work.
when sanding with rubber sanding plate 22 or 26.
Move the power tool upward, downward and in
circular movements to stir the mixture in the best
Operating the wire brushes
manner in its whole volume.
After finishing the works, wash and wipe stirring
Wire brushes allow rust, paint-and-lacquer materials
paddle 19.
and other coatings from various surfaces to be
removed.
Sanding
Install wire brush 29 or 30 as described above.
Sanding with the rubber sanding plate
Start the power tool, wait until the engine gains its
maximum speed and only after that smoothly bring wire
Sanding with this method allows surfaces of various
brush 29 or 30 to the surface processed.
forms and profiles to be processed, and the application
Holding the power tool concerning the surface
of sanding discs with various grits allows surfaces with
processed in such a way so that only the ends of the
various roughness to be achieved.
brush wire contact the surface processed is
recommended. When operating cup wire brush 29, hold
Install rubber sanding plate 22 or 26 as described
the power tool at an angle of 10° to 15° relating to the
surface processed (see picture 18).
above.
English
21

Содержание

Похожие устройства

Скачать