![Makita 9557HNZ [7/64] Operation](/img/pdf.png)
Makita 9557HNZ [7/64] Operation
7
Installing or removing wheel guard
(For depressed center wheel, multi disc /
abrasive cut-off wheel, diamond wheel)
For tool with locking screw type wheel guard
(Fig. 4 & 5)
WARNING:
• When using a depressed center grinding wheel/Multi-
disc, flex wheel, wire wheel brush, cut-off wheel or dia-
mond wheel, the wheel guard must be fitted on the tool
so that the closed side of the guard always points
toward the operator.
• When using an abrasive cut-off / diamond wheel, be
sure to use only the special wheel guard designed for
use with cut-off wheels. (In some European countries,
when using a diamond wheel, the ordinary guard can
be used. Follow the regulations in your country.)
Mount the wheel guard with the protrusion on the wheel
guard band aligned with the notch on the bearing box.
Then rotate the wheel guard to such an angle that it can
protect the operator according to work. Be sure to tighten
the screw securely.
To remove wheel guard, follow the installation procedure
in reverse.
Installing or removing depressed center grinding
wheel/Multi-disc
WARNING:
• Always use supplied guard when depressed center
grinding wheel/Multi-disc is on tool. Wheel can shatter
during use and guard helps to reduce chances of per-
sonal injury.
Mount the inner flange onto the spindle. Fit the wheel/
disc on the inner flange and screw the lock nut onto the
spindle. (Fig. 6)
Super flange (accessory)
Models 9558NB are standard-equipped with a super
flange. Only 1/3 of efforts needed to undo lock nut, com-
pared with conventional type.
To tighten the lock nut, press the shaft lock firmly so that
the spindle cannot revolve, then use the lock nut wrench
and securely tighten clockwise.
To remove the wheel, follow the installation procedure in
reverse. (Fig. 7)
WARNING:
• Only actuate the shaft lock when the spindle is not
moving.
OPERATION
WARNING:
• It should never be necessary to force the tool. The
weight of the tool applies adequate pressure. Forcing
and excessive pressure could cause dangerous wheel
breakage.
• ALWAYS replace wheel if tool is dropped while grind-
ing.
• NEVER bang or hit grinding disc or wheel onto work.
• Avoid bouncing and snagging the wheel, especially
when working corners, sharp edges etc. This can
cause loss of control and kickback.
• NEVER use tool with wood cutting blades and other
sawblades. Such blades when used on a grinder fre-
quently kick and cause loss of control leading to per-
sonal injury.
CAUTION:
• After operation, always switch off the tool and wait until
the wheel has come to a complete stop before putting
the tool down.
Grinding and sanding operation (Fig. 8)
ALWAYS hold the tool firmly with one hand on housing
and the other on the side handle. Turn the tool on and
then apply the wheel or disc to the workpiece.
In general, keep the edge of the wheel or disc at an angle
of about 15 degrees to the workpiece surface.
During the break-in period with a new wheel, do not work
the grinder in the B direction or it will cut into the work-
piece. Once the edge of the wheel has been rounded off
by use, the wheel may be worked in both A and B direc-
tion.
Содержание
- Nb 9557nb 9558nb 1
- English 4
- Explanation of general view 4
- Grinder safety warnings 4
- Specifications 4
- Assembly 6
- Functional description 6
- Installing side grip handle fig 3 6
- Save these instructions 6
- Shaft lock fig 1 6
- Switch action fig 2 6
- Grinding and sanding operation fig 8 7
- Installing or removing depressed center grinding wheel multi disc 7
- Installing or removing wheel guard for depressed center wheel multi disc abrasive cut off wheel diamond wheel 7
- Operation 7
- Super flange accessory 7
- Maintenance 8
- Mm 4 1 2 125 mm 5 8
- Operation with abrasive cut off diamond wheel optional accessory fig 9 8
- Ec declaration of conformity 9
- Optional accessories 9
- Consignes de sécurité pour le meuleuse 10
- Descriptif 10
- Français 10
- Spécifications 10
- Assemblage 13
- Blocage de l arbre fig 1 13
- Conservez ces instructions 13
- Description du fonctionnement 13
- Installation de la poignée latérale manche fig 3 13
- Installation ou retrait de la meule à moyeu déporté ou du multidisque 13
- Installation ou retrait du carter de meule pour meule à moyeu déporté multidisque meule de tronçonnage abrasive et meule diamantée 13
- Interrupteur fig 2 13
- Super flasque accessoire 13
- Meulage et sablage fig 8 14
- Mm 4 1 2 125 mm 5 14
- Utilisation 14
- Utilisation avec une meule de tronçonnage abrasive diamantée accessoire en option fig 9 14
- Accessoires en option 15
- Entretien 15
- Déclaration de conformité ce 16
- Deutsch 17
- Schleifer sicherheitswarnungen 17
- Technische daten 17
- Übersicht 17
- Bewahren sie diese anleitung sorgfältig auf 20
- Funktionsbeschreibung 20
- Montage 20
- Montieren des seitengriffs zusatzgriffs abb 3 20
- Montieren und demontieren der schutzhaube für gekröpfte trennschleifscheibe multischeibe trennschleifscheibe diamantscheibe 20
- Montieren und demontieren einer gekröpften trennschleifscheibe multischeibe 20
- Schalterfunktion abb 2 20
- Spindelarretierung abb 1 20
- Betrieb 21
- Schleif und schmirgelbetrieb abb 8 21
- Superflansch zubehör 21
- Betrieb mit trennschleifscheibe diamantscheibe sonderzubehör abb 9 22
- Mm 4 1 2 125 mm 5 22
- Wartung 22
- Eg übereinstimmungserklärung 23
- Sonderzubehör 23
- Avvertimenti per la smerigliatrice 24
- Dati tecnici 24
- Italiano 24
- Visione generale 24
- Blocco albero fig 1 27
- Conservare queste istruzioni 27
- Descrizione funzionale 27
- Funzionamento dell interruttore fig 2 27
- Installazione dell impugnatura laterale manico fig 3 27
- Installazione o rimozione della protezione disco per disco con centro depresso multidisco disco abrasivo scanalato disco diamantato 27
- Installazione o rimozione disco multidisco con centro depresso 27
- Montaggio 27
- Superflangia accessorio 27
- Funzionamento con il disco abrasivo scanalato diamantato accessorio opzionale fig 9 28
- Mm 4 1 2 125 mm 5 28
- Operazione di smerigliatura e di levigatura fig 8 28
- Operazioni 28
- Accessori opzionali 29
- Manutenzione 29
- Dichiarazione ce di conformità 30
- Nederlands 31
- Technische gegevens 31
- Veiligheidswaarschuwingen voor een slijpmachine 31
- Verklaring van algemene gegevens 31
- Asblokkering fig 1 34
- Beschrijving van de functies 34
- Bewaar deze voorschriften 34
- Ineenzetten 34
- Installeren of verwijderen van de beschermkap voor schijf met een verzonken middengat multischijf doorslijpschijf diamantschijf 34
- Monteren van de zijhandgreep handvat fig 3 34
- Werking van de schakelaar fig 2 34
- Bediening 35
- Installeren of verwijderen van de afbraamschijf multischijf 35
- Slijpen en schuren fig 8 35
- Superflens accessoire 35
- Gebruik met doorslijpschijf diamantschijf optionele accessoire fig 9 36
- Mm 4 1 2 125 mm 5 36
- Onderhoud 36
- Eu verklaring van conformiteit 37
- Optionele accessoires 37
- Advertencias de seguridad para la esmeriladora 38
- Español 38
- Especificaciones 38
- Explicación de los dibujos 38
- Accionamiento del interruptor fig 2 41
- Bloqueo del eje fig 1 41
- Descripción del funcionamiento 41
- Guarde estas instrucciones 41
- Instalación de la empuñadura lateral mango fig 3 41
- Instalación o desmontaje de un disco de amolar de centro hundido multidisco 41
- Instalación o desmontaje del protector de disco para disco de centro hundido multidisco disco de corte abrasivo disco de diamante 41
- Montaje 41
- Súper arandela centradora accesorio 41
- Mm 4 1 2 125 mm 5 42
- Operación 42
- Operación con disco de corte abrasivo disco de diamante accesorio opcional fig 9 42
- Operación de amolado y lijado fig 8 42
- Accesorios opcionales 43
- Mantenimiento 43
- Declaración de conformidad ce 44
- Avisos de segurança para a esmerilhadeira 45
- Especificações 45
- Explicação geral 45
- Português 45
- Guarde estas instruções 47
- Acção do interruptor fig 2 48
- Descrição funcional 48
- Instalar ou retirar a roda de rebarbação deprimido ao centro disco múltiplo 48
- Instalar ou retirar o resguardo da roda para roda deprimida ao centro disco múltiplo disco abrasivo de corte disco diamantado 48
- Instalação do punho lateral pega fig 3 48
- Montagem 48
- Operação 48
- Super flange acessório 48
- Travão do veio fig 1 48
- Manutenção 49
- Mm 4 1 2 125 mm 5 49
- Operação com o disco abrasivo de corte disco diamantado acessório opcional fig 9 49
- Rebarbação e lixamento fig 8 49
- Acessórios opcionais 50
- Declaração de conformidade ce 50
- Illustrationsoversigt 51
- Sikkerhedsadvarsler for sliber 51
- Specifikationer 51
- Beskrivelse af funktionerne 53
- Gem disse forskrifter 53
- Spindellås fig 1 53
- Afbryderkontaktbetjening fig 2 54
- Anvendelse 54
- Montering af sidegreb håndtag fig 3 54
- Montering eller afmontering af den forkrøppede centersliveskive multi skive 54
- Montering og afmontering af beskyttelsesskærm til forkrøppet centerslibeskive multi skive afskæringsskive diamantskive 54
- Samling 54
- Slibning og sandslibning fig 8 54
- Superflange tilbehør 54
- Anvendelse med afskæringsskive diamantskive ekstraudstyr fig 9 55
- Mm 4 1 2 125 mm 5 55
- Vedligeholdelse 55
- Ekstraudstyr 56
- Eu konformitetserklæring 56
- Ελληνικα 57
- Λειαντηρασ πρ ειδ π ιησεισ ασφαλειασ 57
- Περιγραφή γενικής άπ ψης 57
- Τε νικα αρακτηριστικα 57
- Κλείδωμα ά να εικ 1 60
- Περιγραφη λειτ υργιασ 60
- Φυλα ετε αυτεσ τισ δηγιεσ 60
- Δράση διακ πτη εικ 2 61
- Λειτ υργία λείανσης και τριψίματ ς εικ 8 61
- Λειτ υργια 61
- Σ ύπερ φλάντ α παρελκ μεν 61
- Συν λ 61
- Τ π θέτηση ή αφαίρεση τ υ πρ φυλακτήρα τρ ύ για τρ αμηλωμέν υ κέντρ υ π λυδίσκ τρ λείανσης κ πής διαμαντ τρ 61
- Τ π θέτηση ή αφαίρεση τρ ύ λείανσης αμηλωμέν υ κέντρ υ π λύ δίσκ ς 61
- Τ π θέτηση πλάγιας λα ής λα ή εικ 3 61
- Ιλ 4 62
- Ιλ 4 1 2 125 ιλ 5 62
- Λειτ υργία με τρ λείανσης κ πής διαμαντ τρ πρ αιρετικά ε αρτήματα εικ 9 62
- Πρ αιρετικα ε αρτηματα 63
- Συντηρηση 63
- Anjo aichi japan 64
- Makita corporation 64
- Www makita com 64
- Δήλωση συμμ ρφωσης εκ 64
Похожие устройства
- Makita 6271DWPE3 Инструкция по эксплуатации
- Makita DHP453RFE Инструкция по эксплуатации
- Makita PF1110 Инструкция по эксплуатации
- Makita PF1100 Инструкция по эксплуатации
- Makita PF0300 Инструкция по эксплуатации
- Makita GV5010 Инструкция по эксплуатации
- Makita PF0610 Инструкция по эксплуатации
- Makita HR2811F Инструкция по эксплуатации
- Makita HR2450FT, 780 Вт Инструкция по эксплуатации
- Makita DPC6430 Инструкция по эксплуатации
- Makita DPC7331 Инструкция по эксплуатации
- Maman BM2000 Инструкция по эксплуатации
- Maman BM1000 Инструкция по эксплуатации
- Manfrotto MK290XTA3-3W (MT290XTA3 + головка MH804-3W), черный Инструкция по эксплуатации
- Manfrotto MK190X3-3W1 (MT190X3 + головка MH804-3W1), черный Инструкция по эксплуатации
- Marta MT-1947 Инструкция по эксплуатации
- Marta MT-1946 Инструкция по эксплуатации
- Marta MT-1949 Инструкция по эксплуатации
- Marta MT-1948 Инструкция по эксплуатации
- Electrolux ECH/AG-1500 MFR Инструкция по эксплуатации