Mitsubishi Electric PKFY-P50VHM-E [7/40] Operation
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Mitsubishi Electric PKFY-P50VHM-E [7/40] Operation

Mitsubishi Electric PKFY-P25VBM-E [7/40] Operation
7
GB
5.5. Airflow direction setting
<To Change the Airflow’s Up/Down Direction>
With the unit running, press the Airflow Up/Down button
6
as necessary.
•
Each press changes the direction. The current direction is shown at
6
.
• The change sequence, and the available settings, are as follows.
* Note that during swing operation, the directional indication on the
screen does not change in sync with the directional vanes on the unit.
* Some models do not support directional settings.
*1. For MA remote controller only, other remote controllers display the
same as 4steps model.
*2. Airflow direction setting <Auto>
COOL/FAN/DRY : Setting 1 (Horizontal), HEAT : Setting 5 (Downward 5)
Airflow Display
5 steps
model*1
4 steps
model
(PMFY)
4 steps
model
(PKFY-BM)
123 4
(Horiz.)
Swing
Swing
Auto 1 2
3
4
5
Note:
The number of available fan speeds depends on the type of unit
connected. Note also that some units do not provide an “Auto”
setting.
In the following cases, the actual fan speed generated by the unit
will differ from the speed shown the remote controller display.
1. While the display is showing “STAND BY” or “DEFROST”.
2. When the temperature of the heat exchanger is low in the heat-
ing mode. (e.g. immediately after heating operation starts)
3. In HEAT mode, when room temperature is higher than the tem-
perature setting.
4. When the unit is in DRY mode.
5.2. Mode select
Press the operation mode ( ) button
2
and select the op-
eration mode
2
.
Cooling mode
Drying mode
Fan mode
Heating mode
Automatic (cooling/heating) mode
Automatic operation
According to a set temperature, cooling operation starts if the room
temperature is too hot and heating operation starts if the room tem-
perature is too cold.
During automatic operation, if the room temperature changes and
remains 1.5 °C or more above the set temperature for 3 minutes, the
air conditioner switches to cooling mode. In the same way, if the room
temperature remains 1.5°C or more below the set temperature for 3
minutes, the air conditioner switches to heating mode.
5. Operation
Cooling mode
3 minutes (switches from
heating to cooling)
Set temperature +1.5°C
Set temperature
Set temperature -1.5°C
3 minutes (switches from cool-
ing to heating )
Because the room temperature is automatically adjusted in order to
maintain a fixed effective temperature, cooling operation is performed
a few degrees warmer and heating operation is performed a few de-
grees cooler than the set room temperature once the temperature is
reached (automatic energy-saving operation).
5.3. Temperature setting
To decrease the room temperature:
Press
button
3
to set the desired temperature.
The selected temperature is displayed at
3
.
To increase the room temperature:
Press button
3
to set the desired temperature.
The selected temperature is displayed at
3
.
• Available temperature ranges are as follows:
Cooling/Drying: 19 - 30 °C
Heating: 17 - 28 °C
Automatic: 19 - 28 °C
• The display blinks either 8°C - 39°C to inform you if the room tempera-
ture is lower or higher than the displayed temperature.
5.4. Fan speed setting
Press the Fan Speed button
5
as many times as necessary while the
system is running.
• Each press changes the force. The currently selected speed is
shown at
5
.
• The change sequence, and the available settings are as follows.
FAN SPEED
Display
4-speed
+
Auto *
3-speed
+
Auto *
4-speed
model
Speed 1 Speed 2 Speed 3 Speed 4
Speed 1 Speed 2 Speed 3 Speed 4 Auto
■
Automatic fan speed setting (For wireless remote controller)
It is necessary to set for wireless remote controller only when
automatic fan speed is not set at default setting.
It is not necessary to set for wired remote controller with automatic
fan speed at default setting.
1
Press the SET button with something sharp at the end.
Operate when display of remote controller is off.
MODEL SELECT
blinks and Model No. is lighted
A
.
2
Press the AUTO STOP button.
blinks and setting No. is lighted
B
.
(Setting No.01: without automatic fan speed )
3
Press the temp.
buttons to set the setting No.02.
(Setting No.02:with automatic fan speed )
If you mistook the operation, press the ON/OFF
button and oper-
ate again from procedure
2
.
4
Press the SET button with something sharp at the end.
MODEL SELECT
and Model No. are lighted for 3 seconds, then turned off.
ON/OFF TEMP
RESETSET CLOCK
MODEL SELECT
FAN
VANE
TEST RUN
AUTO STOP
AUTO START
h
min
LOUVER
MODE
CHECK
B
A
3
2
14
* For MA remote controller only.
Automatic fan speed setting is necessary for wireless remote controller.
Speed 1 Speed 2 Speed 3 Auto
123 4
(Horiz.)

Содержание

Похожие устройства

Скачать