Clarion APA2160 Инструкция по эксплуатации онлайн [6/8] 2995

Содержание

• Apa2160 1
• Clarion 1
• Introduction 1
• Amplifier controlsand power indicator connection 2
• Electrical connections 3
• Installation 3
• An output signal changes with the position of an output mode selector switch 1ch1 2mono the signal of ch1 and ch2 is mixed and outputted ch2m0n0 only the signal of ch2 is outputted 5
• Applications 5
• Caution 5
• Main unit 5
• Mono mode 5
• Stereo mode 5
• Î warning 5
• Additional help 7
• Adjust the balance control from left to right 7
• After a short two second delay slowly raise 7
• Also refer to the troubleshooting 7
• And listen to the result audio imaging 7
• Another possibility is damaged or under 7
• Apa2160 amplifier reproduces audio 7
• Care when adjusting the controls 7
• Final system checks 7
• Hear any noise static distortion or no 7
• Hear distortion check the connections and 7
• Increase the volume and verify that the 7
• Powered speakers once again refer to 7
• Problem possible cause solution 7
• Section depending on your system design 7
• Should match control setting 7
• Sound at all check the connections and 7
• Start the engine and turn on the main unit 7
• The levels may become quite loud even 7
• The troubleshooting section for 7
• The volume and listen to the sound if you 7
• Trouboleshooting 7
• Verify that the gain controls is set correctly 7
• Without distortion at all frequencies if you 7
• 40 20 80 8
• Packaging content 8
• Specifications 8

Похожие устройства

• Behringer MON 800 MINIMON Инструкция по эксплуатации
• Scher-Khan Magicar A Инструкция по эксплуатации
• Scarlett SC-1046 Инструкция по эксплуатации
• Clarion APA4320 Инструкция по эксплуатации
• Акма V3-600 MOL Инструкция по эксплуатации
• Bosch GBM 16-2 RE 0.601.120.508 Инструкция по эксплуатации
• Behringer MX-400 Инструкция по эксплуатации
• Scher-Khan Magicar B Инструкция по эксплуатации
• Scarlett SC-1045 Инструкция по эксплуатации
• Clarion BLT373 Инструкция по эксплуатации
• Bosch HMT 85ML53 Инструкция по эксплуатации
• Акма V3-500 ⁄ 3 Хром Инструкция по эксплуатации
• Энкор ДЭ-500ЭР/10М 50068 Инструкция по эксплуатации
• Behringer SX 2442FX EURODESK Инструкция по эксплуатации
• Scher-Khan Magicar 3 Инструкция по эксплуатации
• Scarlett SC-1041 Инструкция по эксплуатации
• Акма V3-500 ⁄ 3 Инструкция по эксплуатации
• Clarion BLT373.47 Инструкция по эксплуатации
• Bosch GBM 32-4 0.601.130.208 Инструкция по эксплуатации
• Behringer SX 3242FX EURODECK Инструкция по эксплуатации

Caution When Subwoofer starts pop electrical overload please lower gain control volume and avoid the damage to subwoofer If the sound of subwoofer begins to produce muddiness and distortion amplifier allophone please lower gain control volume avoid that amplifier lapses into a regular functional stop state by fault load and wait to recover clear low pitched sound region sensitivity Adjustment of an electronic crossover function HP LP Caution Clarion recommends turning the amplifier off before changing any switch position This will eliminate any possible damage from transient spikes to the amllfier or speaker system while changing the switch setting 1 HP filter function mid range high region speaker correspondence setup LPF HPF control set to 125Hz is recommended Listen to a variety of music style Rock Rap R B etc and slowly increase or decrease the LPF HPF control until the best performance is realized For most a mid range speaker the crossover point tends to be around 100Hz Setting the crossover frequency too low may cause distortion is produced on a high reproduction level In addition to it there is a possibility of damaging usage s speaker If such a situation occurs please raise crossover frequency please turn LPF HPF control unit adjustment volume clockwise and reduce distortion 2 LP filter function subwoofer correspondence setup LPF HPF control set to 55Hz the position turned to the limit of a counterclockwise rotation is recommended Listen to a variety of music style Rock Rap R B etc and slowly increase or decrease the LPF HPF control until the best performance is realized For mosf subwoofer systems the crossover point tends to be between 55Hz and 120Hz Setting the crossover frequency too high may cause audio system to sound boomy or vocals and speech to become very nasal in tone Speaker Level Input When you connect with a car audio without a RCA output terminal please use a speaker level input terminal Caution Noise or pop sound may be made by a car audio to combine with this amplifier or by a position of a level of gain of this amplifier Car Audio Gray Gray Blackey Right Speaker Output