Home
Главная
Skil
Машины углошлифовальные (УШМ)
9030 LA (F 015 903 0LA)
Инструкция по эксплуатации Страница: 8

Skil 9030 LA (F 015 903 0LA) Инструкция по эксплуатации онлайн [8/180] 326804

into the pinch point can dig into the surface of the

material causing the wheel to climb out or kick out. The

wheel may either jump toward or away from the operator,

depending on the direction of the wheel’s movement at

the point of pinching. Abrasive wheels may also break

under these conditions.

• Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

a) Maintainafirmgriponthepowertoolandposition

yourbodyandarmtoallowyoutoresistkickback

forces.Alwaysuseauxiliaryhandle,ifprovided,for

maximumcontroloverkickbackortorquereaction

duringstart-up.The operator can control torque

reactions or kickback forces, if proper precautions are

taken.

b) Neverplaceyourhandneartherotatingaccessory.

The accessory may kickback over your hand.

c) Donotpositionyourbodyintheareawherepower

toolwillmoveifkickbackoccurs.Kickback will propel

the tool in the direction opposite to the wheel’s movement

at the point of snagging.

d) Usespecialcarewhenworkingcorners,sharp

edgesetc.Avoidbouncingandsnaggingthe

accessory.Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

e) Donotattachasawchainwoodcarvingbladeor

toothedsawblade.Such blades create frequent

kickback and loss of control.

3)SAFETYWARNINGSSPECIFICFORGRINDINGAND

ABRASIVECUTTING-OFFOPERATIONS

a) Useonlywheeltypesthatarerecommendedfor

yourpowertoolandthespecificguarddesignedfor

theselectedwheel.Wheels for which the power tool

was not designed cannot be adequately guarded and are

unsafe.

b) Thegrindingsurfaceofthecentredepressed

wheelsmustbemountedbelowtheplaneofthe

guardlip. An improperly mounted wheel that projects

through the plane of the guard lip cannot be adequately

protected.

c) Theguardmustbesecurelyattachedtothepower

toolandpositionedformaximumsafety,sotheleast

amountofwheelisexposedtowardstheoperator.

The guard helps to protect the operator from broken

wheel fragments, accidental contact with wheel and

sparks that could ignite clothing.

d) Wheelsmustbeusedonlyforrecommended

applications.For example: Do not grind with the side of

a cut-o wheel. Abrasive cut-o wheels are intended for

peripheral grinding; side forces applied to these wheels

may cause them to shatter.

e) Alwaysuseundamagedwheelflangesthatareof

correctsizeandshapeforyourselectedwheel.

Proper wheel anges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-o

wheels may be dierent from grinding wheel anges.

f) Donotuseworndownwheelsfromlargerpower

tools.A wheel intended for a larger power tool is not

suitable for the higher speed of a smaller tool and may

burst.

4)ADDITIONALSAFETYWARNINGSSPECIFICFOR

CUTTING OFF OPERATIONS

a) Donot“jam”thecut-offwheelorapplyexcessive

pressure.Donotattempttomakeanexcessive

depthofcut.Overstressing the wheel increases the

loading and susceptibility to twisting or binding of the

wheel in the cut and the possibility of kickback or wheel

breakage.

b) Donotpositionyourbodyinlinewithandbehind

therotatingwheel.When the wheel, at the point of

operation, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

c) Whenthewheelisbindingorwheninterruptinga

cutforanyreason,switchoffthepowertooland

holdthepowertoolmotionlessuntilthewheel

comestoacompletestop.Neverattempttoremove

thecut-offwheelfromthecutwhilethewheelisin

motion,otherwisekickbackmayoccur.Investigate

and take corrective action to eliminate the cause of wheel

binding.

d) Donotrestartthecuttingoperationinthe

workpiece.Letthewheelreachfullspeedand

carefullyre-enterthecut.The wheel may bind, walk up

or kickback if the power tool is restarted in the workpiece.

e) Supportpanelsoranyoversizedworkpieceto

minimizetheriskofwheelpinchingandkickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

f) Useextracautionwhenmakinga“pocketcut”into

existingwallsorotherblindareas.The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

5)SAFETYWARNINGSSPECIFICFORSANDING

OPERATIONS

a) Whensanding,donotuseexcessivelyoversized

sandingdiscpaper.Followthemanufacturers’

recommendationswhenselectingsandingpaper.

Larger sanding paper extending beyond the sanding pad

presents a laceration hazard and may cause snagging,

tearing of the disc, or kickback.

6)SAFETYWARNINGSSPECIFICFORWIRE

BRUSHING OPERATIONS

a) Beawarethatwirebristlesarethrownbythebrush

evenduringordinaryoperation.Donotoverstress

thewiresbyapplyingexcessiveloadtothebrush.

The wire bristles can easily penetrate light clothing and/

or skin.

b) Iftheuseofaguardisrecommendedforwire

brushing,donotallowanyinterferenceofthewire

wheelorbrushwiththeguard.Wire wheel or brush

may expand in diameter due to work load and centrifugal

forces.

GENERAL

• This tool is not suitable for wet grinding/cutting

• Only use the anges which are supplied with this tool

• This tool should not be used by people under the age of

16 years

Содержание

Похожие устройства

into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out The wheel may either jump toward or away from the operator depending on the direction of the wheel s movement at the point of pinching Abrasive wheels may also break under these conditions Kickback i s th e result of power tool misuse and or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below a Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces Always use auxiliary handle If provided for maximum control over kickback or torque reaction during start up The operator can control torque reactions or kickback forces if proper precautions are taken b Never place your hand near the rotating accessory The accessory may kickback over your hand c Do not position your body In the area where power tool will move If kickback occurs Kickback will propel the tool in the direction opposite to the wheel s movement at the point of snagging d Use special care when working corners sharp edges etc Avoid bouncing and snagging the accessory Comers sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback e Do not attach a saw chain woodcarving blade or toothed saw blade Such blades create frequent kickback and loss of control 3 SAFETY WARNINGS SPECIFIC FOR GRINDING AND ABRASIVE CUTTING OFF OPERATIONS a Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe b The grinding surface of the centre depressed wheels must be mounted below the plane of the guard lip An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected c The guard must be securely attached to the power tool and positioned for maximum safety so the least amount of wheel Is exposed towards the operator The guard helps to protect the operator from broken wheel fragments accidental contact with wheel and sparks that could ignite clothing d Wheels must be used only for recommended applications For example Do not grind with the side of a cut off wheel Abrasive cut off wheels are intended for peripheral grinding side forces applied to these wheels may cause them to shatter e Always use undamaged wheel flanges that are of correct size and shape for your selected wheel Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage Flanges for cut off wheels may be different from grinding wheel flanges f Do not use worn down wheels from larger power tools A wheel intended for a larger power tool is not suitable for the higher speed of a smaller tool and may burst 4 ADDITIONAL SAFETY WARNINGS SPECIFIC FOR CUTTING OFF OPERATIONS a Do not jam the cut off wheel or apply excessive pressure Do not attempt to make an excessive depth of cut Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage b Do not position your body in line with and behind the rotating wheel When the wheel at the point of operation is moving away from your body the possible kickback may propel the spinning wheel and the power tool directly at you c When the wheel Is binding or when interrupting a cut for any reason switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop Never attempt to remove the cut off wheel from the cut while the wheel is In motion otherwise kickback may occur Investigate and take corrective action to eliminate the cause of wheel binding d Do not restart the cutting operation In the workpiece Let the wheel reach full speed and carefully re enter the cut The wheel may bind walk up or kickback if the power tool is restarted in the workpiece e Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback Large workpieces tend to sag under their own weight Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel f Use extra caution when making a pocket cut Into existing walls or other blind areas The protruding wheel may cut gas or water pipes electrical wiring or objects that can cause kickback 5 SAFETY WARNINGS SPECIFIC FOR SANDING OPERATIONS a When sanding do not use excessively oversized sanding disc paper Follow the manufacturers recommendations when selecting sanding paper Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging tearing of the disc or kickback 6 SAFETY WARNINGS SPECIFIC FOR WIRE BRUSHING OPERATIONS a Be aware that wire bristles are thrown by the brush even during ordinary operation Do not overstress the wires by applying excessive load to the brush The wire bristles can easily penetrate light clothing and or skin b If the use of a guard Is recommended for wire brushing do not allow any Interference of the wire wheel or brush with the guard Wire wheel or brush may expand in diameter due to work load and centrifugal forces GENERAL This tool is not suitable for wet grinding cutting Only use the flanges which are supplied with this tool This tool should not be used by people under the age of 16 years 8

Скачать