![Rigol DP821 [10/144] General care and cleaning](/img/pdf.png)
Rigol DP821 [10/144] General care and cleaning
![Rigol DP821 [10/144] General care and cleaning](/views2/1473311/page10/bga.png)
RIGOL
VIII DP800 User’s Guide
General Care and Cleaning
General Care
Do not store or leave the instrument where it may be exposed to direct sunlight for
long periods of time.
Cleaning
Clean the instrument regularly according to its operating conditions. To clean the
exterior surface, perform the following steps:
1. Disconnect the instrument from all power sources.
2. Clean the loose dust on the outside of the instrument with a lint-free cloth (with
a mild detergent or water). When cleaning the LCD, take care to avoid scarifying
it.
CAUTION
To avoid damage to the instrument, do not expose it to caustic liquids.
WARNING
To avoid short-circuit and personal injury resulting from moisture, make
sure the instrument is completely dry before reconnecting it to power
supply.
Содержание
- May 2015 1
- Rigol technologies inc 1
- User s guide dp800 series programmable linear dc power supply 1
- Contact us 3
- Copyright 3
- Guaranty and declaration 3
- Notices 3
- Product certification 3
- Publication number 3
- Software version 3
- Trademark information 3
- General safety summary 4
- Safety requirement 4
- Safety terms and symbols 6
- Allgemeine sicherheits informationen 7
- Sicherheits begriffe und symbole 9
- General care and cleaning 10
- Environmental considerations 11
- Dp800 series overview 12
- Document overview 14
- Content conventions in this manual 15
- Contents 16
- Chapter 1 quick start 19
- Quick start 19
- General inspection 20
- Appearance and dimensions 21
- Front panel 22
- Rear panel 29
- To connect to power 31
- Power on inspection 32
- To replace the fuse 32
- User interface 34
- To use the built in help system 36
- Part list 37
- To install a single instrument 37
- To rack mount the instrument 37
- Installation space 38
- Installation tool 38
- Installation procedures 39
- At this point the diagram of the instrument is as shown in the figure below 43
- Part list 44
- To install two instruments 44
- Installation space 45
- Installation tool 45
- Installation procedures 46
- Chapter 2 front panel operations 51
- Front panel operations 51
- Constant voltage output 52
- Constant current output 56
- Power supply series and parallel connections 58
- Power supply series connection 58
- Power supply parallel connection 59
- To enable the track function 60
- Track function 60
- To track the on off status of the channel output 62
- Sense working mode 63
- Timer and delayer 65
- To set the timer parameters 66
- To edit the timer parameters 67
- To set the end state 67
- To set the number of cycles 67
- To set the number of output groups 67
- To edit the timer parameters manually 68
- To edit the timer parameters using templet 68
- To enable the timer 75
- To save and read the timer file 75
- To set the delay parameters 76
- To set the number of output groups 76
- To edit the delay parameters 77
- To edit the delay parameters manually 77
- To set the end state 77
- To set the number of cycles 77
- To generate the delay parameters automatically 78
- To save and read the delay file 79
- To set the stop condition 79
- To enable the delayer 80
- Advanced functions 81
- Recorder 82
- Analyzer option 83
- Monitor option 86
- Trigger option 87
- Trigger input 88
- Trigger output 89
- Brightness 91
- Contrast 91
- Display setting 91
- Rgb luminance 91
- Display mode 92
- Display theme 92
- User defined start up interface 93
- Store and recall 95
- Browser 96
- File type 96
- Delete 99
- Copy and paste 100
- Utility 101
- I o configuration 102
- To set the lan parameters 102
- To set the rs232 parameters 106
- To set the gpib address 107
- Beeper 108
- Over temperature protection 108
- Power on setting 108
- Screen saver 108
- System setting 108
- Keyboard lock 109
- Track setting 109
- System information 110
- System language 110
- Test calibration 110
- Preset setting 112
- To restore to factory setting 112
- Table 2 2 factory setting 113
- To recall the user defined setting 117
- Options 119
- Key locking 121
- Chapter 3 remote control 123
- Remote control via usb 124
- Remote control via lan option 127
- Remote control via gpib option 130
- Remote control via rs232 option 132
- Chapter 4 troubleshooting 135
- All the specifications are guaranteed when the instrument has been working for more than 30 minutes under the specified operation temperature note unless otherwise noted the specifications are applicable to all the channels of the specified model 137
- Chapter 5 specifications 137
- Appendix a accessories and options 141
- Chapter 6 appendix 141
- Note for all the accessories and options please contact the local office of rigol 141
- Appendix b warranty 142
Похожие устройства
- Bruno Sohnle 17-63156-741 Инструкция по эксплуатации
- Bruno Sohnle 17-63161-252MB Инструкция по эксплуатации
- Bruno Sohnle 17-63162-244MB Инструкция по эксплуатации
- Rigol DP821A Инструкция по эксплуатации(ENG)
- Bruno Sohnle 17-63163-251 Инструкция по эксплуатации
- Bruno Sohnle 17-63183-841 Инструкция по эксплуатации
- Bruno Sohnle 17-73117-741 Инструкция по эксплуатации
- Bruno Sohnle 17-73133-742MB Инструкция по эксплуатации
- Bruno Sohnle 17-73146-741 Инструкция по эксплуатации
- Bruno Sohnle 17-73155-741 Инструкция по эксплуатации
- Rigol DS1074B Инструкция по эксплуатации(ENG)
- Bruno Sohnle 17-73186-761 Инструкция по эксплуатации
- Rigol DS1104B Инструкция по эксплуатации(ENG)
- Bruno Sohnle 17-93102-952MB Инструкция по эксплуатации
- Rigol DS1204B Инструкция по эксплуатации(ENG)
- Alpine DVR-F200 Руководство по эксплуатации
- Alpine HCE-CS1100 Руководство пользователя
- Alpine HCE-C1100D Руководство пользователя
- Alpine HCE-C1100 Руководство пользователя
- Alpine KCX-C2600B Руководство пользователя
Скачать
Случайные обсуждения