![Alpine RUX-C800 [18/67] Automatic measurement function](/img/pdf.png)
Alpine RUX-C800 [18/67] Automatic measurement function
![Alpine RUX-C800 [18/67] Automatic measurement function](/views2/1473386/page18/bg12.png)
16-EN
01GB06PXAH800.fm
ALPINE PXA-H800_EN 68-13530Z65-A (B5)
From a PC
When you connect an external input source, you can name it with a
suitable name (Initial setting: “Auxiliary”).
1
Click [ ] for each AUX and select and click the
external input product name from the pull-down
menu.
Setting item: AUX Name
Setting contents: Auxiliary/TV/EXT.DVD/Portable/Game
• This item becomes possible to set only when AUX IN setting is on.
Setting/Adjusting the Navigation
Guidance Volume (Navi Mix)
If a navigation system is connected, its voice guidance will be mixed
with the system and output from the front speakers (Initial setting:
“OFF”). You can adjust the navigation guidance volume (Initial setting:
“0 dB”).
1
Click [ON] or [OFF] for “Navi Mix” in the main menu.
If you click [ON], select the setting value.
2
Click [ ] or [ ] to adjust the volume.
Setting contents: -10 to +10 dB
• For details on the connection of a navigation system, refer to the
installation manual.
Before Performing Automatic
Measurement
This unit is equipped with ImprintEQ, RoadEQ, and AutoTCR
automatic measurement functions.
Be sure to read before performing automatic
measurement.
• The automatic measurement should be performed in a quiet place
with the engine, air-conditioner, and heater turned off. If a mobile
phone or car phone is installed in the vehicle, move them outside of
the cabin, or turn the power off. Sound other than the measuring
sound (ambient noise around the vehicle, engine noise, and
ringtones) may interfere with measurement, resulting in inaccurate
measurement of the acoustic characteristics of the cabin.
• Be aware that the battery may be drained if you use the unit for an
extended period of time without running the engine.
• The microphone supplied with this product is specifically designed
for this type of measurement. Use of any other microphone will give
poor or no results. Use of microphones other than the one supplied is
not recommended.
• If the system is equipped with a power amplifier with input level
control or a powered subwoofer, the measurement may not be
possible if the input level is set low. However, to perform correct
measurement, the input level should not be set too high.
• For a power amplifier with low-pass filter, turn off the low-pass filter
of the power amplifier to make measurement. The low-pass filter in
the powered subwoofer or the power amplifier for a subwoofer
should be set at the highest cutoff frequency.
Measurement sequence for the automatic measurement
functions
Perform the automatic measurement in the following sequence.
When ImprintEQ is used:
First, ImprintEQ, then RoadEQ.
When ImprintEQ is not used:
First, Auto TCR, then RoadEQ.
• When ImprintEQ is used, AutoTCR is not required.
• When ImprintEQ and AutoTCR are performed after RoadEQ, re-
perform RoadEQ.
Naming the AUX Input (AUX Name)
Automatic
Measurement
Function
WARNING
• Do not perform automatic measurement while the vehicle is
running.
Automatic measurement requires microphones to be installed
in the cabin to measure acoustic characteristics, and the
speakers may output loud noise for measurement. This may
interfere with safe driving and lead to an accident.
01GB00PXAH800.book Page 16 Tuesday, February 8, 2011 9:04 PM
Содержание
- Manual de operación léalo antes de utilizar este equipo 1
- Mode d emploi veuillez lire avant d utiliser cet appareil 1
- Owner s manual please read before using this equipment 1
- Pxa h800 1
- System integration audio processor 1
- Alpine pxa h800_en 68 13530z65 a b5 2
- Gb00pxah800 book page 2 tuesday february 8 2011 9 04 pm 2
- Audio setup adjustment 3
- Automatic measurement function 3
- Basic operation 3
- Contents 3
- English 3
- From a pc 3
- Getting started 3
- Operating instructions 3
- Warning 3
- Audio setup adjustment 4
- Automatic measurement function 4
- Basic operation 4
- From the commander 4
- Use the multi channel function 4
- Information 5
- Other useful features 5
- Caution 6
- Notice 6
- Operating instructions 6
- Warning 6
- Getting started 7
- How to read this manual 7
- Location of controls 8
- Pxa h800 8
- Sound manager for pxa h800 8
- A source button 9
- About operation on a pc 9
- Alpine pxa h800_en 68 13530z65 a b5 9
- B channel button 9
- C func button 9
- Click function switching tab 9
- D view button 9
- E rotary encoder 9
- F mute button 9
- From the pull down menu select the tab to be switched to and click it 9
- G return button 9
- H display 9
- I black out indicator 9
- Operating the function switching tab 9
- Rux c800 commander sold separately 9
- About operating 10
- About the audio setting 10
- Alpine pxa h800_en 68 13530z65 a b5 10
- Before you first use the unit 10
- E availability of operations 10
- Features 10
- Caution 11
- Installing sound manager for pxa h800 11
- Basic operation 12
- Initial system start up 12
- Operating the sound manager for pxa h800 menu 12
- Turning power on and off 12
- Using with ai net connections 12
- Audio adjustment 13
- From a pc 13
- From a pc 14
- Setting defeat 14
- Storing the preset values preset store 14
- Switching the sources 14
- From a pc 15
- Recalling a stored setting preset call 15
- Setting the speaker system output system select 15
- From a pc 16
- Setting the aux input system aux input system select 16
- Setting the speakers speaker setup setting the subwoofers 16
- From a pc 17
- Setting and adjusting the aux input digital input analog aux input digital aux input 17
- Automatic measurement function 18
- Before performing automatic measurement 18
- Setting adjusting the navigation guidance volume navi mix 18
- Warning 18
- From a pc 19
- Setting imprinteq 19
- From a pc 20
- Adjusting and saving the target curve 21
- From a pc 21
- Saving imprinteq measurement data on a pc 21
- Turning imprinteq on off 21
- Adjusting for road noise roadeq 22
- Adjusting the time correction automatically auto tcr 22
- From a pc 22
- From a pc 23
- Turning roadeq on off 23
- Audio setup adjustment 24
- Setting mx plus ai net mode 24
- Setting mx plus standalone mode 24
- From a pc 25
- Setting the graphic eq 25
- From a pc 26
- From a pc 27
- Setting the parametric eq 27
- About the crossover x over 28
- Adjusting x over and switching the phases 28
- From a pc 28
- From a pc 29
- Adjusting the time correction tcr 30
- From a pc 30
- From a pc 31
- Setting the 2 channel signal playback mode 2ch playback mode 32
- Use the multi channel function 32
- From a pc 33
- Using dolby pro logic ii dolby pro logic ii 33
- From a pc 34
- Multi channel function adjustment procedure 34
- Multi channel setup 34
- Adjusting the acoustic image bi phantom 35
- Adjusting the speaker volume level output level 35
- From a pc 35
- Mixing the low range audio for the rear rear mix 35
- Achieving powerful high volume sound listening mode 36
- Adjusting the dvd level dvd level 36
- From a pc 36
- Mixing the low range audio of the center with the front l r center bass split 36
- Setting the linear pcm pcm mode 36
- Audio adjustment 37
- Basic operation 37
- Initial system start up 37
- Turning power on and off 37
- Using with ai net connections 37
- From the commander 38
- Storing the preset values preset store 38
- Switching the sources 38
- From the commander 39
- Recalling a stored setting preset call 39
- Setting the speaker system system select 39
- From the commander 40
- Setting the speakers speaker setup 40
- Setting the subwoofer output sw channel 40
- From the commander 41
- Setting the aux input aux in 41
- Setting the aux input system aux input setup 41
- Adjusting the aux volume level aux level 42
- From the commander 42
- Setting the aux volume input level aux in gain 42
- Setting the digital input digital aux 42
- From the commander 43
- Mixing navi audio guidance navi mix setup 43
- Naming the aux input aux name 43
- Adjusting the time correction automatically auto tcr 44
- Automatic measurement function 44
- Before performing automatic measurement 44
- Turning imprinteq on off 44
- Warning 44
- Adjusting for road noise roadeq 45
- From the commander 45
- Audio setup adjustment 46
- Setting the mx plus ai net mode 46
- From the commander 47
- Setting the mx plus standalone mode 47
- From the commander 48
- Setting the equalizer mode eq mode 48
- Setting the graphic eq 48
- From the commander 49
- Setting the parametric eq 49
- About the crossover x over 50
- From the commander 50
- Adjusting x over and switching the phases 51
- From the commander 51
- Adjusting the time correction tcr 52
- From the commander 52
- From the commander 53
- Setting the time correction adjustment unit tcr parameter 53
- Setting euphony euphony 54
- Setting the 2 channel signal playback mode mode 54
- Use the multi channel function 54
- From the commander 55
- Using dolby pro logic ii dolby plii 55
- Adjusting the speaker volume level output level 56
- From the commander 56
- Multi channel function adjustment procedure 56
- Adjusting the acoustic image bi phantom 57
- From the commander 57
- Mixing the low range audio for the rear rear mix 57
- Achieving powerful high volume sound listening mode 58
- From the commander 58
- Mixing the low range audio of the center with the front l r center bass split 58
- Setting the linear pcm pcm mode 58
- Adjusting the dvd level dvd level 59
- Lowering volume quickly mute 59
- Other useful features 59
- Turning the back light off black out function 59
- Adjusting the brightness level of the display dimmer level 60
- Adjusting the brightness of the display dimmer 60
- From the commander 60
- Setting the color for the commander illumination button illumination 60
- From the commander 61
- Switching the display 61
- Information 62
- System configuration 62
- Alpine pxa h800_en 68 13530z65 a b5 63
- Dolby digital 63
- Dolby pro logic ii 63
- Linear pcm audio 63
- Speaker layout for enjoying dolby digital sound dts sound 63
- Terminology 63
- Calibration error 64
- In case of difficulty 64
- Indication commander rux c800 64
- No data 64
- No mic 64
- No mic roadeq off 64
- System mismatch 64
- Audio supply voltage low 65
- Battery voltage high 65
- Battery voltage low 65
- Hi temp over 85 c 65
- Remote out voltage low 65
- Specifications 65
- Alpine pxa h800_en 68 13530z65 a b5 66
- Dimensions 66
- Pxa h800 width 169 mm 6 3 4 height 50 mm 2 depth 215 mm 8 1 2 rux c800 width 161 mm 6 3 8 height 40 mm 1 5 8 depth 28 mm 1 1 8 66
- Alpine pxa h800_es 68 13530z65 a b5 67
- Es00pxah800 book page 66 tuesday february 8 2011 9 57 pm 67
Похожие устройства
- Alpine RUE-4191 Руководство пользователя
- Alpine RUE-4202 Руководство пользователя
- Alpine RUE-4360 Руководство пользователя
- Alpine DVE-5300 Руководство пользователя
- Alpine DHA-S690 Руководство по эксплуатации
- Alpine KPX-100B Руководство пользователя
- Kenwood KDC-W4527 Инструкция по эксплуатации
- Вольт Engineering АМПЕР Э 9-1/25A V2.0 Руководство по эксплуатации
- Вольт Engineering АМПЕР Э 12-1/25A V2.0 Руководство по эксплуатации
- Вольт Engineering АМПЕР-Т Э 16-1/25A V2.0 Руководство по эксплуатации
- Вольт Engineering АМПЕР-Р Э 16-1/25A V2.0 Руководство по эксплуатации
- Вольт Engineering АМПЕР Э 9-1/32A V2.0 Руководство по эксплуатации
- Вольт Engineering АМПЕР Э 12-1/32A V2.0 Руководство по эксплуатации
- Eplutus DVR-910 Инструкция по эксплуатации
- Вольт Engineering АМПЕР-Т Э 16-1/32A V2.0 Руководство по эксплуатации
- Вольт Engineering АМПЕР-Р Э 16-1/32A V2.0 Руководство по эксплуатации
- Вольт Engineering АМПЕР Э 9-1/40A V2.0 Руководство по эксплуатации
- Eplutus DVR-911 Инструкция по эксплуатации
- Вольт Engineering АМПЕР Э 12-1/40A V2.0 Руководство по эксплуатации
- Eplutus DVR-912 Инструкция по эксплуатации