Hotpoint-Ariston LSF 8357 WH [16/28] Advice regarding the first wash cycle
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Hotpoint-Ariston LSF 8357 WH [16/28] Advice regarding the first wash cycle

Hotpoint-Ariston LSF 8357 WH [16/28] Advice regarding the first wash cycle
EN
16
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain duct
with a minimum diameter of 4 cm. Alternatively, rest it over a
sink or tub; the free end of the hose should not remain
immersed in water.
The special plastic elbow
*
makes it easier to find the best
layout: fix the elbow to the wall
securely in order to prevent the
outlet hose from moving and
spilling the dirty water.
The part of the hose marked
with the letter A should be
between 40 and 100 cm above
the ground (see figure).
We advise against the use of hose extensions.
Electrical connection
Before inserting the plug into the electrical socket, make sure
that:
The socket is earthed and complies with current
regulations.
The socket can withstand the maximum load of the
appliance, which is indicated on the data plate located on
the inside of the door (see chapter entitled Description of
the appliance).
The power supply voltage falls within the values indicated
on the data plate on the inside of the door.
The socket is compatible with the plug of the appliance. If
this is not the case, ask an authorised technician to replace
the plug (see Assistance); do not use extension cables or
multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order
to prevent all potential hazards. (See Assistance)
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
Anti-condensation strip*
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order to
protect it from any condensation which may form.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before
running the first wash cycle, completely fill the salt dispenser
with water and add only then approximately 1 kg of salt (see
chapter entitled Rinse aid and refined salt). The water may
overflow: this is normal and is not a cause for concern. Select
the water hardness value (see chapter entitled Rinse aid and
refined salt).
- After the salt has been poured into the
machine, the LOW SALT indicator light
* switches off.
If the salt container is not filled, the water softener and the
heating element may be damaged as a result.
* Only available in selected models.
A
Technical data
Dimensions
width 45 cm
height 85 cm
depth 60 cm
Capacity 10 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 psi – 145 psi
Power supply
voltage
See appliance data plate
Total absorbed
power
See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EEC dated 16/01/2007
(Low Voltage) and subsequent
modifications
-89/336/EEC dated 03/05/89
(Electromagnetic Compatibility)
and subsequent modifications
-97/17/EC (Labelling)
-2002/96/ CE Waste Electrical
and Electronic Equipment
(WEEE)
AIO77
-

Содержание

Похожие устройства

EN Connecting the water outlet hose Connect the outlet hose without bending it to a drain duct with a minimum diameter of 4 cm Alternatively rest it over a sink or tub the free end of the hose should not remain immersed in water The special plastic elbow makes it easier to find the best layout fix the elbow to the wall securely in order to prevent the outlet hose from moving and spilling the dirty water The part of the hose marked with the letter A should be between 40 and 100 cm above the ground see figure Anti condensation strip After installing the dishwasher open the door and stick the adhesive transparent strip under the wooden shelf in order to protect it from any condensation which may form Advice regarding the first wash cycle After the appliance has been installed immediately before running the first wash cycle completely fill the salt dispenser with water and add only then approximately 1 kg of salt see chapter entitled Rinse aid and refined salt The water may overflow this is normal and is not a cause for concern Select the water hardness value see chapter entitled Rinse aid and refined salt After the salt has been poured into the machine the LOW SALT indicator light switches off M If the salt container is not filled the water softener and the heating element may be damaged as a result M We advise against the use of hose extensions Electrical connection Technical data Before inserting the plug into the electrical socket make sure that The socket is earthed and complies with current regulations The socket can withstand the maximum load of the appliance which is indicated on the data plate located on the inside of the door see chapter entitled Description of the appliance The power supply voltage falls within the values indicated on the data plate on the inside of the door The socket is compatible with the plug of the appliance If this is not the case ask an authorised technician to replace the plug see Assistance do not use extension cables or multiple sockets Dimensions width 45 cm height 85 cm depth 60 cm Capacity 10 standard place settings Water supply pressure 0 05 1 MPa 0 5 10 bar 7 25 psi 145 psi Power supply voltage See appliance data plate Total absorbed See appliance data plate power Fuse IM Once the appliance has been installed the power supply cable and the electrical socket should be easily accessible M The cable should not be bent or compressed IM If the power supply cable is damaged it must be replaced by the manufacturer or its Technical Assistance Service in order to prevent all potential hazards See Assistance AK377 See appliance data plate This dishwasher conforms to the following European Community Directives 2006 95 EEC dated 16 01 2007 Low Voltage and subsequent modifications 89 336 EEC dated 03 05 89 Electromagnetic Compatibility and subsequent modifications 97 17 EC Labelling 2002 96 CE Waste Electrical and Electronic Equipment WEEE M The Company shall not be held responsible for any incidents that occur if these regulations are not observed Only available in selected models 16

Скачать