Samsung DSB-A300W [39/60] Disposal

Samsung DSB-A300W [39/60] Disposal
GB-33
GB
GB-32
DIGITAL SATELLITE RECEIVER
TECHNICAL SPECIFICATIONS
Power supply
Type : SMPS
Input voltage : AC 100-240V~, 50/60 Hz
Fuse rating : 250 V/T1.6AH
Tuner
Freq. Range : 950 ~ 2150 MHz
Input signal level : -65 ~ -25 dBm
Channel selection : PLL frequency synthesizer
Input impedance : 75 unbalanced
Connector type : F type female
LNB power control : 13 V/18 V, 22 kHz tone
DiSEqC : 1.2 supported
Demodulator
Type : QPSK DEMODULATION (DVB-S)
Symbol rate : 2 ~ 45 Ms/s
Inner FEC : Viterbi Convolutional
Coding Rate - 1/2,2/3,3/4,5/6,7/8
Outer FEC : Reed Solomon Coding (204,188), t = 8
Video decoder
System decoding : MPEG 2 ISO/TEC 13818
(transport stream)
Profile and level : MPEG 2 MP@ML (4:2:2)
Data rate : 1~ 15 Mb/s
Video formats : 4:3 (normal) & 16:9 (widescreen)
Picture resolution : 720(H) x 576(V) x 50 fields/sec
Audio Decoder
System decoding : MPEG 1 ISO/TEC 11172~3 layer I & II
Audio mode : mono, dual, stereo, joint stereo
Sampling frequency : 32, 44.1, 48 kHz
Problem Possible cause Solution of the problem
No display LED on Power cord Power cord plug in correctly
the front panel; not plugged in correctly
No power supply
No pictures on the screen Receiver in Standby mode; Set receiver to “On”;
Scart not connected tightly Check connection and correct;
to video output of television;
incorrect channel or video Check channel and video output and
output selected on television correct (TV instruction manual)
No sound Audio cord connected Check connection and correct;
incorrectly;
Loudness level = 0; Increase loudness on television set;
Muting active Press the MUTE key
Remote Control does not incorrect operation; Point remote control
operate directly towards the Receiver.
Batteries dead or inserted Replace batteries or insert correctly
incorrectly
Poor picture quality Signal strength to low Check all wire connections. Check the
signal strength in the “Auto Scanning” menu, correct
alignment of your antenna
On-Screen Error Message Antenna cable not connected Check connection and correct;
“Searching for signal” or not tight;
LNB defective; Change LNB;
incorrect position of the Check position and correct,
satellite antenna; Check the signal strength in
LNB is set to "OFF" in the “Auto Scanning” menu
LNB Setting menu
On-Screen Error Message Satellite not yet set Scan of in “Automatic scanning”
“Channel data or “Manual scanning” menu
does not exist.”
On-Screen Error Messages: Smartcard: (depend on model)
“Please check the - not plugged in correctly; Check the Smartcard.
Smartcard”; - not plugged in. “Insert the Smartcard.”
“Please insert the
Smartcard”.
The device, packaging material (e.g. Styrofoam) and the batteries must never be disposed of with
household refuse. Please obtain appropriate information about the regulations in your community,
and dispose of all refuse in accordance with regulations at the separate locations provided.
DISPOSAL
TROUBLESHOOTING
There is no component
picture(Y, Pb, Pr) or RGB
picture.
Select the video signal type to media
setting menu : Composite, Composite +
RGB, Composite + YUV or S-Video.
Selecting RGB video signal out,
YUV(YPbPr) video out turns off.
Selecting composite+YUV video signal
out, YUV(YPbPr) video out turns on.
MF68-00316B(REV1.1)_GB 2/16/05 10:55 AM Page 32

Содержание

TROUBLESHOOTING TECHNICAL SPECIFICATIONS Problem Possible cause Solution of the problem Power cord plug in correctly No display LED on Power cord the front panel No power supply not plugged in correctly No pictures on the screen Receiver in Standby mode Scart not connected tightly to video output of television incorrect channel or video output selected on television No sound Remote Control does not operate directly Poor picture quality signal strength in On Screen Error Message Searching for signal Power supply Set receiver to On Check connection and correct Type SMPS Input voltage AC 100 240V 50 60 Hz Fuse rating 250 V T1 6AH Tuner Freq Range Check channel and video output and correct TV instruction manual Audio cord connected incorrectly Check connection and correct Loudness level 0 Muting active Increase loudness on television set Press the MUTE key incorrect operation Point remote control towards the Receiver Batteries dead or inserted incorrectly Replace batteries or insert correctly Signal strength to low Check all wire connections Check the the Auto Scanning menu correct alignment of your antenna 950 2150 MHz Input signal level 65 25 dBm Channel selection PLL frequency synthesizer Input impedance 75 Q unbalanced Connector type F type female LNB power control 13 V 18 V 22 kHz tone DiSEqC 1 2 supported Demodulator Type QPSK DEMODULATION DVB S Symbol rate 2 45 Ms s Inner FEC Viterbi Convolutional Coding Rate 1 2 2 3 3 4 5 6 7 8 Outer FEC Antenna cable not connected or not tight LNB defective Check connection and correct Change LNB Video decoder incorrect position of the satellite antenna LNB is set to OFF in LNB Setting menu Check position and correct Check the signal strength in the Auto Scanning menu System decoding Reed Solomon Coding 204 188 t 8 MPEG 2 ISO TEC 13818 transport stream Profile and level On Screen Error Message Channel data does not exist Satellite not yet set Scan of in Automatic scanning or Manual scanning menu On Screen Error Messages Please check the Smartcard Smart card not plugged in correctly not plugged in depend on model Check the Smartcard Insert the Smartcard Selecting RGB video signal out YUV YPbRr video out turns off 1 15 Mb s Video formats 4 3 normal 16 9 widescreen Picture resolution 720 H x 576 V x 50 fields sec Audio Decoder Please insert the Smartcard There is no component picturefY Pb R or RGB picture MPEG 2 MP ML 4 2 2 Data rate Select the video signal type to media setting menu Composite Composite RGB Composite YUV or S Video System decoding MPEG 1 ISO TEC 11172 3 layer I II Audio mode mono dual stereo joint stereo Sampling frequency 32 44 1 48 kHz Selecting composietYUV video signal out YUV YPbPr video out turns on DISPOSAL The device household packaging refuse material Please obtain e g Styrofoam appropriate and the information batteries about the must never be regulations in disposed your of with community and dispose of all refuse in accordance with regulations at the separate locations provided GB 32 R GB 33