![Ariens ST28DLET PRO HYDRO TRACK [21/38] 054 05](/img/pdf.png)
Ariens ST28DLET PRO HYDRO TRACK [21/38] 054 05
![Ariens ST28DLET PRO HYDRO TRACK [21/38] 054 05](/views2/1509893/page21/bg15.png)
EN - 21
CHECK CLUTCH OPERATION
Auger / impeller must stop within 5 seconds
when attachment clutch/impeller brake lever
is released.
Wheels must stop quickly when traction drive
clutch lever is released.
If clutches do not engage or disengage
properly, adjust or repair before operation.
See Attachment Clutch/Brake Adjustment on
page 25 and Traction Drive Clutch
Adjustment on page 27.
CHECK CLUTCH CABLE
ADJUSTMENT
Make sure the attachment clutch and traction
drive clutch are adjusted to the range
specified in Attachment Clutch/Brake
Adjustment on page 25 and Traction Drive
Clutch Adjustment on page 27.
CLEAN ENGINE
Refer to Engine Manual for detailed
instructions.
CHECK ENGINE OIL
The engine crankcase oil should be checked
every 5 hours of operation. Oil level MUST be
maintained in safe operating range on
dipstick at all times or engine damage will
result (See Engine Manual).
Park unit on a level surface. Refer to Engine
Manual for detailed instructions.
CHANGE ENGINE OIL
Refer to Engine Manual for detailed
instructions.
NOTE: Run engine just prior to changing oil,
warm oil will flow more freely and carry away
more contaminants.
CHECK TIRE PRESSURE
(926053, 054, 055)
Keep tires at pressure listed on the tire
sidewall. See Check Tire Pressure on
page 10.
CHECK AUGER GEARCASE
(Figure 17)
IMPORTANT: Proper oil level must be
maintained.
Gear cases are filled to the correct level at
the factory. Unless there is evidence of
leakage, no additional lubricant should be
required. Check oil level each season or
every 25 hours of operation.
IMPORTANT: Be sure unit is resting on a
level surface before checking lubricant levels.
To ensure adequate lubricant level:
1. Remove filler plug and seal washer
(Figure 17). Lubricant must be 2.38" –
2.63" (6.05 cm – 6.68 cm) from the flat
surface of the gear case cover.
IMPORTANT: DO NOT remove the gear case
cover.
2. Check oil level with suitable dipstick
device. Add lubricant if required.
NOTE: Inspect seal washer for wear or
rubber deterioration and replace as needed.
IMPORTANT: Use only Ariens L3 synthetic
severe duty gear lube (Part Number
00068800). Use of other lubricants will void
unit warranty.
3. Reinstall filler screw and seal washer to
80 lbf-in. (9 N•m).
IMPORTANT: DO NOT OVER-TORQUE!
Note that measurements are in pound force
inches (lbf-in) and not pound force foot (lbf-ft).
IMPORTANT: Be sure to install seal washer
with rubber side down (Figure 17).
IMPORTANT: Improper torquing, omission of
seal washer, or incorrect installation of seal
washer will void unit warranty.
Figure 17
1. Auger Gearcase
2. Oil Fill Plug
3. Seal Washer
2
1
3
Содержание
- Hydro pro sno thr 1
- Manuel du propriétaire utilisateur 1
- Models 1
- Owner operator manual 1
- Engine manual 2
- Introduction 2
- Manuals 2
- Model and serial numbers 2
- Product registration 2
- Table of contents 2
- Delivery 3
- Disclaimer 3
- Unauthorized replacement parts 3
- Attention 4
- Become alert 4
- Notations 4
- Obey the message 4
- Personal safety is involved 4
- Practices and laws 4
- Required operator training 4
- Safety 4
- Safety alerts 4
- Safety decals and locations 4
- Danger 5
- Emission control system 6
- Safety rules 6
- Assembly 8
- Install discharge chute chute control and chute rod 8
- Package contents 8
- Tools required 8
- Unfold handlebar 8
- Check auger gearcase oil 10
- Check engine crankcase oil 10
- Check function of all controls 10
- Check function of dual handle interlock 10
- Check tire pressure 926053 054 055 10
- Check track tension 926056 10
- Fill fuel tank 10
- Remote deflector control 10
- Run in attachment belt 10
- Setting neutral position 10
- Controls and features 11
- Attachment clutch right hand lever 13
- Controls and features 13
- Dual handle interlock 13
- Ignition switch 120vac start 13
- Operation 13
- Primer bulb 13
- Speed selector 13
- Traction drive clutch left hand lever 13
- Choke control knob 14
- Choke run 14
- Discharge chute 14
- Electric starter 14
- Quick turn chute control 14
- Recoil starter handle 14
- Remote deflector control 14
- Snow clean out tool 14
- Throttle 14
- Differential lock 926056 15
- Moving the unit with the engine off 15
- Drift cutters 16
- Heated handles 16
- Scraper blade 16
- Skid shoes 16
- Track angle 926056 16
- Add fuel stabilizer to extend fuel storage life 17
- Add fuel to fuel tank 17
- Filling fuel tank 17
- Gasoline 17
- Check axle lock 926056 18
- Check dual handle interlock 18
- Check engine fuel crankcase oil 18
- Check function of clutches 18
- Check skid shoes 18
- Frozen impeller 18
- Fuel shut off valve 18
- Manual start 18
- Pre start 18
- Starting and shut off 18
- To stop in an emergency 18
- Electric start 120v 19
- Shut off 19
- Snow removal 19
- Tips for operation 19
- Transport 19
- Traveling 19
- Check dual handle interlock 20
- Check fasteners 20
- Maintenance 20
- Maintenance schedule 20
- Service position 20
- 054 05 21
- Change engine oil 21
- Check auger gearcase 21
- Check clutch cable adjustment 21
- Check clutch operation 21
- Check engine oil 21
- Check tire pressure 21
- Clean engine 21
- Auger shaft 22
- General lubrication 22
- For replacement 23
- Scraper blade 23
- Service and adjustments 23
- Shear bolts 23
- Skid shoes 23
- Handlebar height 24
- Remote deflector control 24
- Attachment clutch brake adjustment 25
- Discharge chute control 25
- Remove attachment cable slack 25
- Speed selector adjustment 25
- Check attachment idler arm roller clearance 26
- Attachment drive belts replacement 27
- Check attachment brake 27
- Check belt finger clearance 27
- Remove old attachment drive belts 27
- Traction drive clutch adjustment 27
- Install new attachment drive belts 28
- Traction drive belt replacement 28
- Height adjuster cable adjustment 926056 29
- Track tension adjustment 926056 29
- Add fuel stabilizer 30
- Fuel system 30
- Long term 30
- Short term 30
- Storage 30
- Accessories 31
- Engine problems 31
- Engine stops 31
- Engine will not crank start 31
- Problem probable cause correction 31
- Service parts 31
- Troubleshooting 31
- Does not operate in forward reverse 32
- Problem probable cause correction 32
- Troubleshooting 32
- Unit throws snow poorly or does not throw snow 32
- Automatic traction control 33
- Height in cm 33
- Length in cm 33
- Specifications 33
- Traction control with axle mounted lockout 33
- Weight lbs kg 33
- Width in cm 33
- X 4 8 41 x 12 20 16 x 6 8 41 x 16 20 5 13 7 track 33
- And chore performing equipment limited warranty 34
- Sno te 34
- Sno thr 34
- Sno thro sno tek and chore performing equipment limited warranty 34
- Special extensions 34
- Customer responsibilities 35
- Exceptions and limitations 35
- To find an authorized service representative 35
- Australian consumer law 36
- Disclaimer 36
- Disclaimer of further warranty 36
- Exclusions items not covered by this warranty 36
- Limitation of remedy and damages 36
- Special exclusions on utility vehicles 36
- California and epa united states environmental protection agency evaporative emission control warranty statement 37
Похожие устройства
- Ariens ST28DLET PRO TRACK Руководство пользователя
- Ariens ST28LET TRACK Руководство пользователя
- Ariens ST30DLE DELUXE Руководство пользователя
- Ariens SNO-TEK 28E Руководство пользователя
- Ariens POWER BRUSH 28 Руководство пользователя
- Yanmar YDP 40 STN-E Руководство пользователя
- Sdmo ST 2.36 H Руководство пользователя
- Sdmo TR 2.36 H Руководство пользователя
- Sdmo ST 3.60 H Руководство пользователя
- Sdmo TR 3.60 H Руководство пользователя
- Sdmo HP 2.26 H Руководство пользователя
- Sdmo XC 2.34 H Руководство пользователя
- Honda WMP 20 Руководство пользователя
- Gardena 3500/4E Classic Руководство пользователя
- Whirlpool AWT 2240 Таблица программ
- Whirlpool AWT 2240 Инструкция по эксплуатации
- Kawasaki ZXR 400 Сервисный мануал
- Kawasaki ZXR 400 Инструкция по эксплуатации
- Gardena Classic 4000/4i EP Инструкция по эксплуатации
- Al-Ko HW 600 Eco Инструкция по эксплуатации