Samsung DSB-S300V [39/60] Disposal

Samsung DSB-S300V [39/60] Disposal
GB-33
GB
GB-32
DIGITAL SATELLITE RECEIVER
TECHNICAL SPECIFICATIONS
Power supply
Type : SMPS
Input voltage : AC 100-240V~, 50/60 Hz
Fuse rating : 250 V/T1.6AH
Tuner
Freq. Range : 950 ~ 2150 MHz
Input signal level : -65 ~ -25 dBm
Channel selection : PLL frequency synthesizer
Input impedance : 75 unbalanced
Connector type : F type female
LNB power control : 13 V/18 V, 22 kHz tone
DiSEqC : 1.2 supported
Demodulator
Type : QPSK DEMODULATION (DVB-S)
Symbol rate : 2 ~ 45 Ms/s
Inner FEC : Viterbi Convolutional
Coding Rate - 1/2,2/3,3/4,5/6,7/8
Outer FEC : Reed Solomon Coding (204,188), t = 8
Video decoder
System decoding : MPEG 2 ISO/TEC 13818
(transport stream)
Profile and level : MPEG 2 MP@ML (4:2:2)
Data rate : 1~ 15 Mb/s
Video formats : 4:3 (normal) & 16:9 (widescreen)
Picture resolution : 720(H) x 576(V) x 50 fields/sec
Audio Decoder
System decoding : MPEG 1 ISO/TEC 11172~3 layer I & II
Audio mode : mono, dual, stereo, joint stereo
Sampling frequency : 32, 44.1, 48 kHz
Problem Possible cause Solution of the problem
No display LED on Power cord Power cord plug in correctly
the front panel; not plugged in correctly
No power supply
No pictures on the screen Receiver in Standby mode; Set receiver to “On”;
Scart not connected tightly Check connection and correct;
to video output of television;
incorrect channel or video Check channel and video output and
output selected on television correct (TV instruction manual)
No sound Audio cord connected Check connection and correct;
incorrectly;
Loudness level = 0; Increase loudness on television set;
Muting active Press the MUTE key
Remote Control does not incorrect operation; Point remote control
operate directly towards the Receiver.
Batteries dead or inserted Replace batteries or insert correctly
incorrectly
Poor picture quality Signal strength to low Check all wire connections. Check the
signal strength in the “Auto Scanning” menu, correct
alignment of your antenna
On-Screen Error Message Antenna cable not connected Check connection and correct;
“Searching for signal” or not tight;
LNB defective; Change LNB;
incorrect position of the Check position and correct,
satellite antenna; Check the signal strength in
LNB is set to "OFF" in the “Auto Scanning” menu
LNB Setting menu
On-Screen Error Message Satellite not yet set Scan of in “Automatic scanning”
“Channel data or “Manual scanning” menu
does not exist.”
On-Screen Error Messages: Smartcard: (depend on model)
“Please check the - not plugged in correctly; Check the Smartcard.
Smartcard”; - not plugged in. “Insert the Smartcard.”
“Please insert the
Smartcard”.
The device, packaging material (e.g. Styrofoam) and the batteries must never be disposed of with
household refuse. Please obtain appropriate information about the regulations in your community,
and dispose of all refuse in accordance with regulations at the separate locations provided.
DISPOSAL
TROUBLESHOOTING
MF68-00331A_GB 6/16/04 1:11 PM Page 32

Содержание

TROUBLESHOOTING TECHNICAL SPECIFICATIONS Problem Possible cause Solution of the problem Power cord plug in correctly No display LED on Power cord the front panel No power supply not plugged in correctly No pictures on the screen Receiver in Standby mode Scart not connected tightly Power supply Set receiver to On Check connection and correct incorrect channel or video No sound Check channel and video output and correct TV instruction manual Check connection and correct Audio cord connected incorrectly Loudness level 0 Muting active Remote Control does not Increase loudness on television set Press the MUTE key incorrect operation AC 100 240V 50 60 Hz Fuse rating 250 V T1 6AH Freq Range 950 2150 MHz Input signal level 65 25 dBm Channel selection PLL frequency synthesizer Input impedance 75 Q unbalanced Connector type F type female LNB power control 13 V 18 V 22 kHz tone DiSEqC 1 2 supported Point remote control operate directly towards the Receiver Poor picture quality signal strength in SMPS Input voltage Tuner to video output of television output selected on television Type Batteries dead or inserted incorrectly Replace batteries or insert correctly Signal strength to low Check all wire connections Check the the Auto Scanning menu correct Demodulator Type QPSK DEMODULATION DVB S Symbol rate 2 45 Ms s Inner FEC Viterbi Convolutional alignment of your antenna On Screen Error Message Searching for signal Coding Rate 172 2 3 3 4 5 6 7 8 Antenna cable not connected or not tight Check connection and correct Outer FEC Reed Solomon Coding 204 188 t 8 LNB defective incorrect position of the Change LNB Check position and correct Video decoder satellite antenna LNB is set to OFF in Check the signal strength in System decoding MPEG 2 ISO TEC 13818 Profile and level MPEG 2 MP ML 4 2 2 the Auto Scanning menu transport stream LNB Setting menu On Screen Error Message Scan of in Automatic scanning Satellite not yet set or Manual scanning menu Channel data does not exist On Screen Error Messages Please check the Smartcard not plugged in correctly depend on model Check the Smartcard Smartcard not plugged in Insert the Smartcard Data rate 1 15 Mb s Video formats 4 3 normal 16 9 widescreen Picture resolution 720 H x 576 V x 50 fields sec Audio Decoder Please insert the Smartcard System decoding MPEG 1 ISO TEC 11172 3 layer I II Audio mode mono dual stereo joint stereo Sampling frequency 32 44 1 48 kHz DISPOSAL The device household packaging refuse material Please obtain e g Styrofoam appropriate and the information batteries about the must never be regulations in disposed your of with community and dispose of all refuse in accordance with regulations at the separate locations provided GB 32 R V GB 33 0

Скачать