Danfoss VLT AQUA Drive FC-202P5K5S2 — как использовать функцию копирования параметров устройства [15/40]

Содержание

• Table of contents p.3
• Connection p.4
• Dc zwischenkreis netz motor p.4
• Dc link circuit mains p.4
• Control terminals in basic unit without a b or c options p.6
• Inverter p.6
• See section 1 for a description of switches s201 s202 and s801 the maximum rated voltage on analogue inputs 53 and 54 is 20 v p.6
• Relay 1 relay 2 p.6
• Only for fc 200 with safe stop p.6
• Function of dip switches in basic unit without a b or c options p.8
• Digital input programming options p.9
• Selectable not selectable x factory setup see programming manual for details p.10
• Operation via lcp 102 p.11
• Graphical control unit lcp 102 p.11
• Warning p.12
• Operating mode p.12
• Explanation of lcp 102 status display p.12
• Direction p.12
• Status line p.12
• Reference source p.12
• Parameter set p.12
• Operational status p.12
• Operating range p.12
• Easy commissioning p.13
• Commissioning menu submenu q2 of quick menu p.13
• Other commonly used parameters in the main menu p.14
• Using the lcp copy function parameter 0 50 to transfer device parameters p.15
• Parameter setting with mct 10 software p.16
• Access via rs 232 ethernet or usb converter p.17
• Profibus dp interface p.18
• General settings p.18
• Warnings alarms and alarm resetting p.19
• Fault analysis p.19
• If the drive does not restart after an alarm reset p.20
• Warning and alarm indications p.21
• Visual alarm indication p.24
• Start stop four pole motor motor thermistor reference 0 50 hz via terminal 53 motor thermistor monitoring on terminal 19 visual alarm indication p.24
• Start stop four pole motor motor thermistor p.24
• Reference 0 50 hz via terminal 53 motor thermistor p.24
• Monitoring on terminal 19 p.24
• Application examples p.24
• Start stop four pole motor oversynchronous motor thermistor 0 72 hz reference value via terminal 53 motor thermistor monitoring on terminal 19 visual alarm indication p.25
• Start stop two pole motor motor thermistor reference 0 50 hz via potentiometer on terminal 53 motor thermistor monitoring on terminal 19 visual alarm indication p.26
• Start stop two pole motor oversynchronous motor thermistor 0 72 hz reference value via terminal 53 motor thermistor monitoring on terminal 19 visual alarm indication p.27
• Start stop motor thermistor reference 0 50 hz terminal 53 motor thermistor monitoring on terminal 19 visual alarm indication p.28
• Fixed speeds three diff erent speeds preset references can be selected via fl oating contacts p.29
• Automatic fast ramp the starts up with fast acceleration and then runs with slow acceleration reference 0 1500 rpm via potentiometer p.30
• Manual off automatic selection with reference value input via keypad in the switch position auto the reference is active via potentiometer in the switch position manual the reference can be set using the up and down buttons in the switch position off the motor is stopped p.31
• Manual off automatic selection with reference value input via potentiometer in switch position auto the reference is active via potentiometer in switch position manual the unit can only be operated via the display in switch position off the motor is stopped p.32
• Manual profi bus time out selection with profi bus control the converter does not accept any commands via the terminals if profi bus control is interrupted the converter automatically switches to manual mode reference setting via buttons manual mode can also be selected via terminal 18 p.33
• Pressure control in pressure control with integrated process controller internal reference feedback 0 100 on terminal 54 p.34
• Pressure control in pa pressure control with integrated process controller internal reference feedback 0 2000 pa on terminal 54 p.35
• Pressure control in bar with pipe compensation pressure control using integrated process controller with pipe pressure drop compensation internal reference feedback 0 10 bar on terminal 54 p.36
• H as 0 20 ma signal on terminal 42 p.37
• Volume fl ow control in m³ h feedback signal output 0 20 ma volume fl ow control with integrated process controller internal reference feedback 0 5000 p.37
• H on terminal 54 feedback output 0 5000 p.37
• Volumetric fl ow control in m³ h oversynchronous feedback signal output 0 20 ma volume fl ow control with integrated process controller internal reference feedback 0 5000 p.38
• H on terminal 54 feedback output 0 5000 p.38
• H as 0 20 ma signal on terminal 42 p.38
• Pressure control in bar basic cascade controller pressure control with integrated process controller the vlt aqua drive cascade controller can switch on additional pumps via the relays if necessary controlled variable 0 10 bar on terminal 54 p.39