Home
Главная
Moser
Машинка Для Стрижки
ChromStyle white
Инструкция по эксплуатации Страница: 13

Moser ChromStyle white [13/94] English

ENGLISH

Should the sensor system recognise such a situation, an acoustic signal will sound and the LED

display will blink for 2 minutes after the appliance has been switched off. The acoustic signal and

the blinking of the LED display can be cancelled by briefly switching the appliance on and off.

Before using the appliance again, it is

urgently recommended to clean the appliance and oil the

blade set. For this purpose, please proceed as follows (failure to observe these instructions may

result in damage to and early failure of the appliance and will void all guarantee claims):

· Switch off the appliance using the on/off switch (Fig. 2b).

· Remove the attachment comb and the blade set and use the cleaning brush to clean the open-

ing of the housing and the blade set. (Fig. 7).

· Oil the blade set (Fig. 8).

Changing the blade set

· Switch off the appliance using the on/off switch (Fig. 2b).

· The blade set can be removed by sliding it away from the housing in the direction of the arrow

(Fig. 6a).

· Replace the blade set by hooking it into the housing and pressing it down until it clicks into posi-

tion in the housing (Fig. 6b).

Disposal in EU countries

Do not dispose of the appliance with domestic refuse. As part of the EU Directive govern-

ing the disposal of electrical and electronic equipment, the appliance is accepted free of

charge by local waste collection points or recycling centres. Correct disposal will ensure

environmental protection and prevent any potentially harmful impacts on people and the

environment.

Disposal in non-EU countries

· Please dispose of the appliance at the end of its service life in an environmentally friendly

manner.

· Disconnect the plug-in transformer from the mains power supply and switch on the appliance to

discharge the battery completely.

· Remove the blade set (Fig. 6a) and use a screwdriver to remove the screws in the opening of

the housing (Fig. 9). Pull the housing parts apart and remove the entire drive with the PCB

(Fig. 10).

· Pull battery off circuit board. If necessary, use a screwdriver to pry them off (Fig. 11).

· Take the batteries to an appropriate collection point.

· Once the batteries have been removed, the appliance may no longer be connected to the

mains!

Содержание

Похожие устройства

ENGLISH Should the senso system recognise such a situation an acoustic signal wil sound and the LED dsplay wil Wink fa 2 minutes after the appiance has been switched off The acoustic signal and the blinking of the LED display can be canceled by briefly switching the appliance on and off Befae using the appiance again it is urgently recommended to dean the appiance and oi the Wade set Fa this purpose please proceed as fdlows failure to observe these instructions may resiit in damage to and earty failure of the appiance and wil void all guarantee daims en Switch off the appliance using the orVoff switch Fig 2b Remove the attachment comb and the blade set and use the cleaning brush to dean the open ing of the housing and the blade set Fig 7 Oil the Wade set Fig 8 Changing the blade set Switch off the appliance using the orVoff switch Fig 2b The Wade set can be removed by sliding it away frcm the housing n the drecticn of the arrow Ag 6a Replace the blade set by hocking it into the housing and pressing it down until it dicks into posi tion in the housing Fig 6b Disposal in EU countries X Do not dspose of the appiance with domestic refuse As part of the EU Directive govern ing the disposal of electrical and electronic equpment the appiance is accepted free of charge by local waste cdlection points a recyding centres Correct disposal wil enstre environmental protection and prevent any potentialy harmful impacts on people and the environment Disposal in non EU countries Please dispose of the appiance at the end of its service ife in an environmentaly friendy manner Disconnect the plug in transformer frcm the mans power supply and switch on the appiance to discharge the battery completely Remove the Wade set Fig 6a and use a screwdiver to remove the screws in the opening of the housing Fig 9 Pdl the housing parts apart and remove the entire dive with the PCB Rg 10 Pul battery off droit board If necessary use a screwdriver to pry them off Fig 11 Take the batteries to an appropriate colecticrn pant Once the batteries have been removed the appiance may no longer be connected to the mans 13

Скачать