Home
Главная
Moser
Машинка Для Стрижки
1400-0050
Инструкция по эксплуатации Страница: 7

Moser 1400-0050 [7/48] English

ENGLISH

Description of parts

A Blade set

B Cutting length adjustment lever

C On/off switch

D Mains cable

E Locking switch for cutting length adjustment

F Attachment comb

G Blade guard

H Cleaning brush

I Oil for blade set

Not shown: optional attachment combs, clippers or hairstyling comb

(depending on model)

Important safety information

For your own protection from injuries and electric shocks, the follow-

ing information must be observed when using electrical equipment:

Read these operating instructions carefully and make sure you

understand them before using the appliance!

· Only use hair clippers to cut human hair.

Only use animal clippers to cut animal hair and animal fur.

· Only use the appliance for the proper use as described in the

operating instructions.

· Keep packaging away from children.

· This appliance is not suitable for use by people (including children)

with physical, sensory or mental disabilities or who do not have

the relevant experience or knowledge of using such appliance,

unless under the supervision of or after having received instruction

in the use of the appliance by an individual who is responsible for

their safety. Children should be supervised to ensure they do not

play with the appliance.

· The operating instructions should be retained so that they can be

referred to at a later date and should be passed on to all subse-

quent owners or users of the appliance.

· Only operate the appliance with an alternating current and with the

voltage stated on the nameplate.

Warning:

· Do not use the appliance near bath tubs, showers or

other water-filled containers. It should also not be used

in areas of high humidity. Always disconnect from the

mains power supply after use since water can pose a

hazard, even when the appliance is switched off.

· Never touch electrical equipment that has fallen into

water.

Disconnect from the mains immediately.

· If the appliance is dropped into water, it may not be

used again subsequently.

· It is essential to PREVENT electrical equipment from

coming into contact with water or other liquids.

· Never use the appliance with wet hands or feet.

· Never use the appliance when barefoot.

· As additional safety measure, it is recommended that a tested

residual current appliance (RCD) with a residual operating current

of not more than 30 mA be installed in the bathroom circuit. Ask

your electrician for advice.

· Disconnect from the mains before cleaning or servicing the

appliance.

· Never use the appliance if it is defective, if it has fallen onto the

floor or if the mains cable is damaged. A damaged mains cable

may only be replaced with an original replacement cable by an

authorised Service Centre or another similarly qualified person, in

order to avoid hazards.

· Repairs may only be performed at an authorised Service Cen-

tre using original parts. Only specialists properly trained in the

handling of electrotechnical appliances may repair electrical

equipment.

· Only use accessories recommended by the manufacturer.

· When disconnecting the appliance from the mains, never pull on

the mains cable or on the appliance itself.

· Do not hold the appliance by the mains cable to carry it and do

not use the cable as a handle.

· Do not wind the mains cable around the appliance.

· Keep the mains cable and appliance away from hot surfaces.

· Make sure that the mains cable is not twisted or kinked when used

and stored.

· Never use the appliance where aerosol (spray) products are being

used or where oxygen is released.

· Do not expose the appliance to temperatures below 0°C and

above +40°C for any length of time. Avoid direct exposure to

sunlight.

· The appliance is not intended for commercial use.

· The appliance is safety insulated and radio screened. It meets the

requirements of EU Directive 2004/108/EC regarding electromag-

netic compatibility and EC Low Voltage Directive 2006/95/EC.

· We are not liable for damage caused as a result of improper use

or failure to observe these operating instructions.

Start-up

· Oil the blade set (Fig. 5).

· Connect to the mains power supply.

· Using the on/off switch, switch on the appliance (Fig. 1

ⓐ

Note for types 1170 and 1400: the audible click that can some-

times be heard when switching on the appliance is a result of the

torque of the alternating current drive unit. This is normal and no

failure of the appliance.

· Using the on/off switch, switch off the appliance after use

(Fig. 1

ⓑ

) and disconnect from the mains.

Cutting length adjustment (Type 1170 and Type 1400)

· Without the attachment comb, the normal cutting length of the

appliance is approx. 0.1 mm.

· The cutting length can be adjusted between 0.1 and 3 mm, even

when the appliance is in use.

· Slide down the locking switch (Fig. 2

ⓑ

)

· By moving the adjustment lever at the side (Fig. 3

ⓐ

), it is possible

to set the cutting length at various pre-set positions (MultiClick).

· Sliding the locking switch upward (Fig. 2

ⓐ

) unlocks the setting

and restores the normal cutting length of approx. 0.1 mm.

Attaching/removing the attachment comb

· Slide the attachment comb on to the blade set in the direction of

the arrow until it reaches the limit stop (Fig. 4

ⓐ

· The attachment comb can be removed by pushing it in the direc-

tion of the arrow (Fig. 4

ⓑ

Cutting with attachment combs (Type 1170 and

Type 1400)

Depending on the model, various attachment combs are included in

the scope of supply. Attachment combs #1 (4.5 mm), #2 (6 mm), #3

(9 mm), #4 (14 mm), #5 (19 mm) and an adjustable attachment comb

(4 - 18 mm) are also optionally available as accessories.

To achieve the desired cutting lengths, the adjustment lever should

not be locked (Fig. 3

ⓑ

); to this end, slide the locking switch upward

(Fig. 2

ⓐ

Cleaning and Care

· Do not immerse the appliance in water!

· After each use, remove the hair clippings from the blade set with

the cleaning brush.

· Only wipe the appliance with a soft cloth, which may be damp-

ened slightly.

Do not use solvents or abrasives!

· For a long-lasting, good cutting performance, it is important to oil

the blade set frequently (Fig. 5).

· If the cutting performance deteriorates after long use despite regu-

lar cleaning and oiling, the blade set should be replaced.

· Use the blade guard when the appliance is not in use.

· Always store the appliance with the blade guard in place.

Changing the bottom blade and the top blade

· Switch off the appliance using the on/off switch (Fig. 1

ⓑ

· Disconnect from the mains power supply.

· Undo both screws on the blade set; remove the bottom blade and

the top blade (Fig. 7).

Moser 1400-0050 [7/48] English

Содержание

Похожие устройства