Mipro ACT707D Инструкция по эксплуатации онлайн
2CE150
ElectronicsCo.,Ltd.
Headoffice:814,Pei-KangRoad,Chiayi,600,Taiwan.
Taipeioffice:5,Lane118,Sung-tehRoad,100,Taipei,Taiwan.
Web-http://www.mipro.com.tw
E-mail:@mipro.com.twmipro
InstructionManual
ACT-707DDualChannelWirelessReceiver
ACT-707DChannelWirelessReceiverDual
Содержание
- Act 707d dual channel wireless receiver act 707d channel wireless receiver dual 1
- Electronics co ltd 1
- Instruction manual 1
- Act dual channel wireless receiver 2
- Belt pack transmitter 2
- Contents act dual channel wireless receiver 2
- Handheld wireless microphone 2
- Included accessories 2
- Introduction 2
- Operating instructions 2
- Act dual channel wireless receiver act dual channel wireless receiver 3
- Parts name and functions 3
- Act dual channel wireless receiver act dual channel wireless receiver 4
- Installation of the receiver 4
- Act dual channel wireless receiver act dual channel wireless receiver 5
- Designations o f buttons and functions 5
- G ch freq sq vol name remo 5
- Operation of receiver with lcd display panel 5
- Receiver operating procedures 5
- Act dual channel wireless receiver act dual channel wireless receiver 6
- Freq menu 6
- Act dual channel wireless receiver act dual channel wireless receiver 7
- Exit menu 7
- Name menu 7
- Sq menu 7
- The operation provids mute control switch 7
- Act act exit 8
- Act dual channel wireless receiver act dual channel wireless receiver 8
- Exit menu 8
- Act dual channel wireless receiver act dual channel wireless receiver 9
- Antenna socket has 8 volts dcpower supply please do not short the circuit of this part 9
- Cautions 9
- Computer network interface operation 9
- Except for receiver module both receiver withlcd displayhavethe most advance function ofcomputer network interfaced controlling system 9
- Use only mipro standard antenna to ensure the sensitivity ofthe receiver 9
- When using dc power supply please be aware of the operating voltage first of all please make sure minimum of 12 volts can be obtained for function properly however the power supply should not exceed its maximum capacity of 15 volts when the supply voltage is more than 15 volts the system will suffer severe internaldamage it is preferred the power source is from a regulated power with the minimum current of 1 a 9
- Wiring instruction 9
- Battery insertion 10
- Functions of lcd display 10
- Grille protects cartridge prevents pop noise andprevents microphone from rolling with polygonal shape 2 color ring for frequency differentiation 3 housing upper portion to be connected to a capsulemodule andbattery internally it holds transmitter pcb 4 functions of lcd display 5 battery compartment designed to accommodate two1 v aa batteries 6 battery cap covers battery in the battery compartment 7 anti roll ring for frequency differentiation 8 act signal receptor receiving act signal and adjusting frequency automatically 10
- Handheld wireless microphone handheld wireless microphone 10
- Insert two 1 v aa batteries correctly into thebattery compartment with the positive pole points at the microphone capsule then screw the batterycap 6 back to microphone as shown in fig 2 10
- Parts names and functions 10
- Ps when the microphone is not in use make sure thepower of themicrophone is off if the microphone will not be used for some time please remove the batteries from the battery compartmenttoavoid battery leakage and result in damagedbattery springsand circuit if a rechargeable battery was used takeit outand recharge it 10
- Unscrew battery cap 6 in a counter clockwise direction 10
- Belt pack transmitter belt pack transmitter 11
- Parts names and functions 11
- Af 4 pin input connection methods 12
- Before power on ascertain if same channel 7 was set up for both receiver and microphone if notadjust to same channel accordingly 12
- Belt pack transmitter belt pack transmitter 12
- Operating instructions 12
- Plug the microphone connector intothe input jack 1 and tighten the connector screwby clockwisedirection as shownin fig 2 12
- The led indicator flashes briefly when power on indicating normal battery status ifno flash occurs it has either no battery the battery is drained or installed incorrectly changeaccordingly 12
- Toadjust gt mtswitch 10 and gain control 8 simply push down both snap locks on the sides of battery cover and flipit backwardsto expose the adjustment panel 12
- Battery installation 13
- Belt pack transmitter belt pack transmitter 13
- Functions of lcd display 13
- Inserta two 1 aa batteries into the batterycompartmentaccording to the correct polarity as shown in fig then push up to close the battery compartment as shown infig 4 13
- Ps when the microphone isnot in use make sure the p ower ofthe microphone is off if the microphone will not be used for some time pleaseremove the batteries from the battery compartment to avoid battery leakage and result indamaged b attery springs andcircuit if a rechargeable battery was used take it out and recharge it 13
- Pushing down both snap locks on the sides of battery cover to open battery cover take out the batteries fig 3 13
Похожие устройства
- Mipro ACT707DE Инструкция по эксплуатации
- Mipro ACT707HM Инструкция по эксплуатации
- Mipro ACT707S Инструкция по эксплуатации
- Mipro ACT707SE Инструкция по эксплуатации
- Mipro ACT707TM Инструкция по эксплуатации
- Mipro ACT81 Инструкция по эксплуатации
- Mipro ACT82 Инструкция по эксплуатации
- AXIOMET AX-T02 Расширенная инструкция
- AXIOMET AX-T02 Инструкция
- AXIOMET AX-T03 Инструкция
- AXIOMET AX-T03 Расширенная инструкция
- Mipro ACT8H Инструкция по эксплуатации
- AXIOMET AX-T01 Расширенная инструкция
- AXIOMET AX-T01 Инструкция
- Mipro ACT8T Инструкция по эксплуатации
- Mipro AD-808 Инструкция по эксплуатации
- AXIOMET AX-TI220 Инструкция
- AXIOMET AX-TI220 Расширенная инструкция
- AXIOMET AX-T2400 Инструкция
- AXIOMET AX-T2400 Расширенная инструкция