Candy AQUA 1042D1/2-S [9/40] Setting up installation

Candy AQUA 1042D1/2-S [9/40] Setting up installation
9
A
B
C
EN
CHAPTER 5
SETTING UP
INSTALLA
TION
Move the machine near its
permanent position without
the packaging base.
Cut tube-holding straps.
Unscrews the two top screws
A and remove the cover,
sliding it off horizontally.
Remove the cardboard
protection.
Unscrews the two tie braces
B on the crosspiece (with an
H. 19 spanner) and remove
the polystyrene spacers C
under it.
Please do not fit the 2 tie
braces B again!
IMPORTANT:
DO NOT REMOVE THE
SPACERS ABOVE THE
CROSSPIECE.
Lean the machine forward
and remove the plastic
bags containing the two
polystyrene blocks at the
sides, pulling downwards.
Replace the cover with the
two screws A.
Please ensure when fitting
the table top the locating
pins are inserted correctly in
their slots, positioned on the
side of the cabinet as shown
in the relevant diagram.
WARNING:
DO NOT LEAVE THE
PACKAGING IN THE
REACH OF CHILDREN AS
IT IS A POTENTIAL
SOURCE OF DANGER.
BG
ëíêÄçàñÄ 5
åéçíÄÜ
èÂÏÂÒÚÂÚ Û‰‡ ·ÎËÁÓ ‰Ó
ÏflÒÚÓÚÓ Ì‡ ËÁÔÓÎÁ‚‡Ì ·ÂÁ
ÓÒÌÓ‚‡Ú‡ ̇ ÓÔ‡Íӂ͇ڇ.
éÚÂÊÂÚ Á‡‰˙ʇ˘ËÚ Ú˙·‡Ú‡
ÎÂÌÚË.
ê‡Á‚ËÈÚ ‰‚‡Ú‡ „ÓÌË ‚ËÌÚ‡ Ä Ë
χıÌÂÚ ͇ԇ͇, ͇ÚÓ „Ó ËÁ‰˙Ô‡ÚÂ
ıÓËÁÓÌÚ‡ÎÌÓ.
å‡ıÌÂÚ Ô‰ԇÁËÚÂÎfl ̇ ÔÎÓÚ‡.
ê‡Á‚ËÈÚ ‰‚ÂÚ ÒÍÓ·Ë B ̇
Ú‡‚ÂÒ‡Ú‡ (Ò „‡Â˜ÂÌ Íβ˜ H 19 ) à
χıÌÂÚ ÒÚÂËÓÔÓÌËflÚ
‡Á‰ÂÎËÚÂÎ C ÔÓ‰ ÌÂfl.
åÓÎfl Ì Á‡ÍÂÔ‚‡ÈÚ ‰‚ÂÚ ÒÍÓ·Ë
B ÓÚÌÓ‚Ó.
ÇçàåÄçàÖ:
çÖ åÄïÄâíÖ
êÄáÑÖãàíÖãü çÄÑ
íêÄÇÖêëÄíÄ.
ç‡ÍÎÓÌÂÚ χ¯Ë̇ڇ ̇Ô‰ Ë
χıÌÂÚ ̇ÈÎÓÌÓ‚ËÚ ÚÓ·Ë Ò
‰‚‡Ú‡ ÒÚÂËÓÔÓÌË ·ÎÓ͇ ÓÚÒÚ‡ÌË
͇ÚÓ „Ë ËÁ‰˙Ô‡Ú ̇‰ÓÎÛ.
èÓÒÚ‡‚ÂÚ ͇ԇ͇ Ò‰‚‡Ú‡ ‚ËÌÚ‡ Ä.
åÓÎfl Û‚ÂÂÚ ÒÂ, ˜Â Á‡ÍÂÔ‚‡˘ËÚÂ
ÔÎÓÚ‡ ˘ËÔÍË Ò‡ ‚ÎÂÁÎË ÚÓ˜ÌÓ Ì‡
ÏÂÒÚ‡Ú‡ ÒË, ÔÓÁˈËÓÌË‡ÌË
ÓÚÒÚ‡ÌË Ì‡ ÍÓÔÛÒ‡ ͇ÍÚÓ Â
ÔÓ͇Á‡ÌÓ Ì‡ ‰Ë‡„‡Ï‡Ú‡.
ÇçàåÄçàÖ:
çÖ ÑÄÇÄâíÖ çÄ ÑÖñÄ
ÖãÖåÖçíàíÖ éí
éèÄäéÇäÄíÄ, èéêÄÑà
èéíÖçñàÄãçÄ
éèÄëçéëí.

Содержание

СТРАНИЦА 5 CHAPTER 5 МОНТАЖ SETTING UP INSTALLATION Преместете уреда близо до мястото на използване без основата на опаковката Move the machine near its permanent position without the packaging base Отрежете задьржащите трьбата ленти Cut tube holding straps Развийте двата горни винта А и махнете капака като го издърпате хоризонтално Махнете предпазителя на плота Unscrews the two top screws A and remove the cover sliding it off horizontally Remove the cardboard protection Развийте двете скоби В на траверсата с гаечен ключ Н19 И махнете стериопорният разделител С под нея Unscrews the two tie braces B on the crosspiece with an H 19 spanner and remove the polystyrene spacers C under it Моля не закрепвайте двете скоби В отново Please do not fit the 2 tie braces B again ВНИМАНИЕ НЕ МАХАЙТЕ РАЗДЕЛИТЕЛЯ НАД ТРАВЕРСАТА IMPORTANT DO NOT REMOVE THE SPACERS ABOVE THE CROSSPIECE Наклонете машината напред и махнете найлоновите торби с двата стериопорни блока отстрани като ги издърпате надолу Lean the machine forward and remove the plastic bags containing the two polystyrene blocks at the sides pulling downwards Поставете капака сдвата винта А Моля уверете се че закрепващите плота щипки са влезли точно на местата си позиционирани отстрани на корпуса както е показано на диаграмата Replace the cover with the two screws A Please ensure when fitting the table top the locating pins are inserted correctly in their slots positioned on the side of the cabinet as shown in the relevant diagram ВНИМАНИЕ НЕ ДАВАЙТЕ НА ДЕЦА ЕЛЕМЕНТИТЕ ОТ ОПАКОВКАТА ПОРАДИ ПОТЕНЦИАЛНА ОПАСНОСТ WARNING DO NOT LEAVE THE PACKAGING IN THE REACH OF CHILDREN AS IT IS A POTENTIAL SOURCE OF DANGER 9

Скачать