![Gigabyte H252-Z10 (rev. 100) [5/131] Electrostatic discharge esd](/img/pdf.png)
Gigabyte H252-Z10 (rev. 100) [5/131] Electrostatic discharge esd
![Gigabyte H252-Z10 (rev. 100) [5/131] Electrostatic discharge esd](/views2/1681212/page5/bg5.png)
Electrostatic Discharge (ESD)
CAUTION!
ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU
PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,
PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-
TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER
WHEN HANDLING PARTS.
Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by
their edges without any component and pin touching. After removing a board from its protective
wrapper or from the system, place the board component side up on a grounded, static free sur-
face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over
any surface.
System power on/off: To remove power from system, you must remove the system from rack.
Make sure the system is removed from the rack before opening the chassis, adding, or removing
any non hot-plug components.
Hazardous conditions, devices and cables: Hazardous electrical conditions may be present
on power, telephone, and communication cables. Turn off the system and discon-nect the cables
attached to the system before servicing it. Otherwise, personal injury or equipment damage can
result.
Electrostatic discharge (ESD) and ESD protection: ESD can damage drives, boards, and
other parts. We recommend that you perform all procedures in this chapter only at an ESD work-
station. If one is not available, provide some ESD protection by wearing an antistatic wrist strap
attached to chassis ground (any unpainted metal surface on the server) when handling parts.
ESD and handling boards: Always handle boards carefully. They can be extremely sensi-tive to
electrostatic discharge (ESD). Hold boards only by their edges. After removing a board from its
protective wrapper or from the system, place the board component side up on a grounded, static
free surface. Use a conductive foam pad if available but not the board wrapper. Do not slide
board over any surface.
Installing or removing jumpers: A jumper is a small plastic encased conductor that slips over
two jumper pins. Some jumpers have a small tab on top that can be gripped with n-gertips or
with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when us-
ing needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with the
Содержание
- 2019 giga byte technology co ltd all rights reserved the trademarks mentioned in this manual are legally registered to their respective owners 2
- Copyright 2
- Disclaimer 2
- Documentation classifications 2
- For more information 2
- In order to assist in the use of this product gigabyte provides the following types of documentation 2
- Information in this manual is protected by copyright laws and is the property of gigabyte changes to the specifications and features in this manual may be made by gigabyte without prior notice no part of this manual may be reproduced copied translated transmitted or published in any form or by any means without gigabyte s prior written permission 2
- Conventions 3
- The following conventions are used in this user s guide 3
- Server warnings and cautions 4
- Electrostatic discharge esd 5
- Chapter 1 hardware installation 1 7
- Chapter 2 system appearance 7 7
- Chapter 3 system hardware installation 3 7
- Chapter 4 motherboard components 3 7
- Chapter 5 bios setup 5 7
- Table of contents 7
- 3 amd cbs menu 79 8
- 4 amd pbs option menu 92 8
- 5 chipset setup menu 95 8
- 6 server management menu 97 8
- 7 security menu 103 8
- 8 boot menu 106 5 9 save exit menu 108 5 10 abl post codes 109 8
- 11 agesa post codes 119 9
- 12 bios post beep code ami standard 130 9
- 13 bios recovery instruction 131 9
- 1 installation precautions 11
- Chapter 1 hardware installation 11
- 2 product specifications 12
- 3 system block diagram 16
- 1 front view 17
- 2 rear view 17
- Chapter 2 system appearance 17
- 3 front panel led and buttons 18
- No name color status description 18
- 2 1 2 2 1 19
- 4 system lan leds 19
- 5 hard disk drive leds 20
- Green on off 20
- Led 2 hdd present no hdd 20
- Note 1 depends on hba utility spec 2 blink cycle depends on hdd s activity signal 3 if hdd is pulled out during rebuilding the disk status of this hdd is regarded as faulty 20
- System appearance 20 20
- 6 power supply unit psu led 21
- Psu led 21
- This page left intentionally blank 22
- Chapter 3 system hardware installation 23
- 1 installing the hard disk drive 24
- 2 removing the node 25
- 3 removing chassis cover 26
- 4 removing and installing the fan duct 27
- 5 removing and installing the heatsink 28
- 6 installing the cpu 29
- 7 1 eight channel memory configuration 30
- 7 installing memory 30
- 7 2 installing the memory 31
- 7 3 dimm population table 31
- 8 installing the pci expansion card 33
- 9 installing the m device and heat sink 36
- 10 replacing the fan module 37
- 11 replacing the power supply 38
- 12 cable routing 39
- Hdd back plane board signal 40
- On board sata top 40
- Nvme top 41
- On board sata bottom 41
- Nvme bottom 42
- 1 motherboard components 43
- Chapter 4 motherboard components 43
- 2 jumper setting 44
- Motherboard components 44 44
- Bios setup program function keys 45
- Chapter 1 bios setup 45
- Chapter 5 bios setup 45
- Advanced 46
- Amd cbs 46
- Amd pbs option 46
- Chipset 46
- Save exit 46
- Security 46
- Server management 46
- 1 the main menu 47
- 2 advanced menu 49
- 2 1 trusted computing 50
- 2 2 psp firmware versions 51
- 2 3 legacy video select 52
- 2 4 ast2500 super io configuration 53
- 2 4 1 serial port 1 2 configuration 54
- 2 5 s5 rtc wake settings 56
- 2 6 serial port console redirection 57
- 2 7 cpu configuration 59
- 2 7 1 cpu 0 information 60
- 2 8 pci subsystem 61
- 2 9 usb configuration 63
- 2 10 nvme configuration 65
- 2 11 sata configuration 66
- 2 12 network stack 67
- 2 13 amd mem configuration status 68
- 2 14 iscsi configuration 69
- 2 15 tls auth configuration 70
- 2 16 avago megaraid configuration utility 71
- 2 17 intel r i350 gigabit network connection 73
- 2 18 vlan configuration 75
- 2 19 mac ipv4 network configuration 77
- 2 20 mac ipv6 network configuration 78
- 3 amd cbs menu 79
- 3 1 valhalla common options 80
- 3 2 df common options 82
- 3 3 umc common options 83
- 3 3 1 ddr4 common options 84
- 3 3 2 dram memory mapping 85
- 3 3 3 nvdimm 86
- 3 3 4 memory mbist 87
- 3 4 nbio common options 88
- 3 5 fch common options 89
- 3 6 ntb common options 90
- 3 7 soc miscellaneous control 91
- 4 amd pbs option menu 92
- 4 1 ras 93
- 5 chipset setup menu 95
- 5 1 north bridge 96
- 6 server management menu 97
- 6 1 system event log 99
- 6 2 view fru information 100
- 6 3 bmc network configuration 101
- 6 4 ipv6 bmc network configuration 102
- 7 security menu 103
- 7 1 secure boot 104
- 8 boot menu 106
- 9 save exit menu 108
- 10 1 startprocessortestpoints 109
- 10 2 memory test points 109
- 10 3 pmu test points 109
- 10 abl post codes 109
- 10 4 original post code 110
- 10 5 cpu test points 111
- 10 6 topology test points 111
- 10 7 extended memory test point 111
- 10 8 gnb earlier init 112
- 10 10 abl0 test points 115
- 10 11 abl5 test points 115
- 10 9 pmu test points 115
- 11 1 universal post code 119
- 11 2 0xa1xx for cz only memory postcodes 119
- 11 agesa post codes 119
- 11 3 s3 interface post code 122
- 11 4 pmu post code 122
- 11 5 0xa5xx assigned for agesa psp module 122
- 11 6 0xa9xx 0xaaxx assigned for agesa nbio module 125
- 11 7 0xacxx assigned for agesa ccx module 127
- 11 8 0xadxx assigned for agesa df module 128
- 11 9 0xafxx assigned for agesa fch module 128
- 12 1 pei beep codes 130
- 12 2 dxe beep codes 130
- 12 bios post beep code ami standard 130
- 13 bios recovery instruction 131
Похожие устройства
- Gigabyte H242-Z10 (rev. 100) Руководство пользователя ErP Mode BIOS Setup
- Gigabyte H242-Z10 (rev. 100) Руководство пользователя GSM Agent
- Gigabyte H242-Z10 (rev. 100) Руководство пользователя GSM Server
- Gigabyte H242-Z10 (rev. 100) Инструкция
- Gigabyte H242-Z11 (rev. 100) Руководство пользователя ErP Mode BIOS Setup
- Gigabyte H242-Z11 (rev. 100) Руководство пользователя GSM Agent
- Gigabyte H242-Z11 (rev. 100) Руководство пользователя GSM Server
- Gigabyte H242-Z11 (rev. 100) Инструкция
- Gigabyte H262-Z61 (rev. 100) Руководство пользователя GSM Server
- Gigabyte H262-Z61 (rev. 100) Руководство пользователя GSM Agent
- Gigabyte H262-Z61 (rev. 100) Руководство пользователя ErP Mode BIOS Setup
- Gigabyte H262-Z61 (rev. 100) Инструкция
- Gigabyte H262-Z62 (rev. 100) Руководство пользователя ErP Mode BIOS Setup
- Gigabyte H262-Z62 (rev. 100) Руководство пользователя GSM Agent
- Gigabyte H262-Z62 (rev. 100) Руководство пользователя GSM Server
- Gigabyte H262-Z62 (rev. 100) Инструкция
- Gigabyte H262-Z63 (rev. 100) Руководство пользователя GSM Agent
- Gigabyte H262-Z63 (rev. 100) Руководство пользователя ErP Mode BIOS Setup
- Gigabyte H262-Z63 (rev. 100) Руководство пользователя GSM Server
- Gigabyte H262-Z63 (rev. 100) Инструкция