![ASRock K7S8XE Инструкция онлайн [17/27] 539348](/img/pdf.png)
ASRock K7S8XE Инструкция онлайн [17/27] 539348
![ASRock K7S8XE Инструкция онлайн [17/27] 539348](/views2/1692524/page17/bg11.png)
17
AMIBIOS SETUP UTILITY - VERSION 3.31a
Main
Type
Cylinders
Heads
Write Precompensation
Sectors
Maximum Capacity
LBA Mode
Block Mode
Fast Programmed I/O Modes
32 Bit Transfer Mode
Ultra DMA Mode
[ Setup Help ]
F1:Help
Esc:Previous Menu
F9:Setup Defaults
F10:Save & Exit
+/-:Change Values
Enter:Select
Sub-Menu
:Select Item
Primary IDE Master
Off
Off
Auto
Off
Auto
Select how to set the
parameters of drive,
Or
Select [AUTO] to set
all HDD parameters
automatically.
Auto
TYPE
To set the type of the IDE device, first, please select “IDE Devices” on Main
menu and press <Enter> to get into the sub-menu. Then, select among
“Primary IDE Master”, “Primary IDE Slave”, “Secondary IDE Master”, and
“Secondary IDE Slave” to make configuration of its type. Below are the
configuration options.
[USER]: It allows user to manually enter the number of cylinders, heads,
and sectors per track for the drive.
Before attempting to configure a hard disk drive, make sure you
have the correct configuration information supplied by the drive
manufacturer. Incorrect settings may cause the system to fail
to recognize the installed hard disk.
[Auto]: Select [Auto] to automatically detect hard disk drive. If auto-
detection is successful, the BIOS Setup automatically fills in the
correct values for the remaining fields on this sub-menu. If the auto-
detection fails, it may due to that the hard disk is too old or too new.
If the hard disk was already formatted on an older system, the BIOS
Setup may detect incorrect parameters. In these cases, select [User]
to manually enter the IDE hard disk drive parameters.
After entering the hard disk information into BIOS, use a disk utility,
such as FDISK, to partition and format new IDE hard disk drives.
This is necessary so that you can write or read data from the hard
disk. Make sure to set the partition of the Primary IDE hard disk
drives to active.
Содержание
- K7s8xe 1
- User manual 1
- Copyright notice 2
- Disclaimer 2
- Appendix 20 3
- Bios setup 15 3
- Contents 3
- Installation 9 3
- Introduction 4 3
- Software support 19 3
- Chapter 1 introduction 4
- Package contents 4
- Specifications 5
- Caution 6
- Cm 9 in 7
- Motherboard layout 7
- Sis 748 chipset 7
- 5 6 7 8 9 10 8
- Asrock i 8
- Chapter 2 installation 9
- Cpu installation 9
- Pre installation precautions 9
- Screw holes 9
- Installation of cpu fan and heatsink 10
- Installation of memory modules dimm 10
- Expansion slots pci and agp slots 11
- Installing an expansion card 11
- Jumpers setup 12
- Connectors 13
- Bios menu bar 15
- Bios setup utility 15
- Chapter 3 bios setup 15
- Legend bar 15
- Main menu 16
- Advanced security power boot and exit menus 18
- Asrock pc diy live demo program 19
- Chapter 4 software support 19
- Contact information 19
- Drivers menu 19
- Install operating system 19
- Running the support cd 19
- Support cd information 19
- Utilities menu 19
- Advanced bios setup menu 20
- Appendix advanced bios setup 20
- Spread spectrum this field should always be disabled for better system stability 20
- This section will introduce you the following bios setup menus advanced security power boot and exit 20
- Advanced 21
- Agp aperture size 21
- Agp aperture size it refers to a section of the pci memory address range used for graphics memory it is recommended to leave this field at the default value unless the installed agp card s specifications requires other sizes usb controller use this to enable or disable the use of usb controller usb device legacy support use this to enable or disable the support to emulate legacy i o devices such as mouse keyboard etc dram cas latency this is used to adjust the means of memory accessing configuration options auto 2t 2 t 3t 21
- Chipset configuration 21
- Dram cas latency 21
- Usb controller usb device legacy support 21
- Onboard fdc onboard serial port onboard infrared port onboard parallel port parallel port mode epp version parallel port irq parallel port dma channel onboard midi port midi irq select onboard game port onboard ide onboard lan onboard ac 97 audio 22
- Pci latency timer pci clocks primary graphics adapter agp data rate agp fast write 22
- Pci latency timer pci clocks the default is 32 it is recommended to keep the default value unless the installed pci expansion cards specifications require other settings primary graphics adapter select pci or agp as the primary graphics adapter agp data rate the default setting is auto you may select between 8x or 4x for an agp 3 card or select among 4x 2x 1x for an agp 2 card agp fast write this allows you to enable or disable the feature of agp fast write protocol support 22
- Peripheral configuration 22
- Resource configuration 22
- Security setup menu 24
- Power setup menu 25
- Boot setup menu 26
- Quick boot mode enable this mode will speed up the boot up routine by skipping memory retestings boot up num lock if this is enabled it will automatically activate the numeric lock function after boot up boot to os 2 this enables boot up to os 2 operating system boot from network use this to enable or disable boot from network feature boot device priority this allows you to set the boot device priority 26
- Exit menu 27
- Original values will be restored and all changes are discarded 27
Похожие устройства
- ASRock K7S8XE R3.0 Инструкция
- ASRock K7S8XE+ Инструкция
- ASRock M810LMR Инструкция
- ASRock K7VT2 Инструкция
- ASRock K7VM2 R3.0 Инструкция
- ASRock K7VM2 Инструкция
- ASRock K7VM3 Инструкция
- ASRock K7VM3 Краткая инструкция
- ASRock K7VT4-4X Инструкция
- ASRock K7VM4 Инструкция
- ASRock K7VT4A Инструкция
- ASRock K7VT4A+ Инструкция
- ASRock K7VT4A PRO Инструкция
- ASRock K7VT6 Инструкция
- ASRock K7VT6-C Инструкция
- ASRock K7VT6-C Краткая инструкция
- ASRock K7Upgrade-600 Инструкция
- ASRock K7Upgrade-600 Краткая инструкция
- ASRock BTC PRO Kit Инструкция
- ASRock Front USB 3.1 Panel Инструкция