Icom IC-M700PRO [27/28] Transmitter
![Icom IC-M700PRO [27/28] Transmitter](/views2/1074635/page27/bg1b.png)
8
SPECIFICATIONS AND OPTIONS
23
■ Specifications
GENERAL
• Frequency coverage:
Receive 500 kHz–29.999 MHz
Transmit 1.6– 2.9999 MHz 4.0– 4.9999 MHz
6.0– 6.9999 MHz 8.0– 8.9999 MHz
12.0– 13.9999 MHz 16.0–17.9999 MHz
18.0– 19.9999 MHz 22.0–22.9999 MHz
25.0– 27.5000 MHz
• Mode: USB, AM, CW, FSK and AFSK
(
available modes differ with version)
• Number of channels: 150 channels (max.)—
3 groups of 50
channels each
• Antenna impedance: 50 Ω nominal
• Usable temp. range: –30°C to +60°C (–22°F to +140°F)
• Frequency stability: ±10 Hz
(–30°C to +60°C; –22°F to +140°F)
(±20 Hz above 15 MHz for General and
Marine versions)
• Power supply requirement: 13.6 V DC±15%
(negative and floating grounds
available depending on version)
• Current drain:
Transmit
(max. output power) 30 A
Receive
(max. audio output) 2.5 A (negative ground)
• Dimensions: 291.4(W)×116.4(H)×315(D) mm
11.3(W)×4.4(H)×12.8(D) in
• Weight: 7.9 kg; 17.4 lb
(negative ground)
TRANSMITTER
• Output power: 150 W
PEP
(60 W above 24 MHz)
• Spurious emissions: –75 dB
typical
• Carrier suppression: 65 dB
typical
• Unwanted sideband suppression: 70 dB typical
• Microphone impedance: 600 Ω
RECEIVER
• Sensitivity
USB, CW, AFSK, FSK,
(for 12 dB SINAD):
0.35 µV
typical (1.8–29.9999 MHz)
1.0 µV (1.6–1.7999 MHz)
6.3 µV (0.5–1.5999 MHz)
AM (for 10 dB S/N)
:
2.2 µV
typical (1.8–29.9999 MHz)
6.3 µV (1.6–1.7999 MHz)
32 µV (0.5–1.5999 MHz)
• Spurious response rejection: 80 dB
typical (1.6–29.9999 MHz)
• Audio output power: 5.0 W (at 10% distortion with a 4 Ω load)
• Audio impedance: 4 to 8 Ω
• Clarity variable range: ±150 Hz
■ Options
AT-130 AUTOMATIC
ANTENNA TUNER
MN-100
ANTENNA MATCHER
MN-100L
ANTENNA MATCHER
HS-50 HANDSET
Matches the transceiver to a
long wire antenna with a mini-
mum of insertion loss.
Matches the transceiver to a
dipole antenna. Covers all HF
bands from 1.5 to 30 MHz.
8m × 2 antenna wires come
attached.
Matches the transceiver to a
long wire antenna. Covers all
HF bands from 1.5 to 30 MHz.
15 m × 1 antenna wire comes
attached.
Provides better audio recep-
tion during offshore conditions
and comes in handy for listen-
ing privacy on board.
PS-60 DC POWER SUP-
PLY
PS-66 DC-DC CON-
VERTER
FL-100
CW/FSK NARROW FILTER
Provides 13.6 V DC (30 A)
output from an AC outlet.
Provides 13.6 V DC (30 A)
output from a 19–32 V DC
power source.
Allows better receiver selectiv-
ity for CW and FSK.
Bandwidth: 500 Hz/–6 dB
UT-95 2-TONE ALARM UNIT
Provides an alarm transmis-
sion for emergency use during
maritime operation.
All stated specifications are subject to change without notice
or obligation.
Содержание
- Im700pro 1
- Explicit definitions 2
- Important 2
- Precautions 2
- R warning 2
- General 3
- In case of emergency for maritime operation 3
- Marine 3
- Version description 3
- Versions 3
- Table of contents 4
- Call procedures 5
- Operating rules and guidelines 5
- Priorities 5
- Privacy 5
- Radio licenses 5
- I front panel 6
- Panel description 6
- Agc agc 8
- Dup simp 8
- I display 8
- Scan sql n b 8
- I memory mode vfo mode 9
- I selecting a channel 9
- Selecting a channel frequency 9
- D scan function 10
- I selecting a frequency 10
- Caution 11
- I resetting the cpu 11
- I basic voice receive and transmit 12
- I functions for transmit 12
- Receive and transmit 12
- D agc off function 13
- D clarity control 13
- D noise blanker 13
- D squelch function 13
- I functions for receive 13
- Cw key connection 14
- Fsk terminal unit connection 14
- I cw operation 14
- I fsk operation 14
- I set mode contents 15
- I set mode operation 15
- Set mode 15
- 4 scan speed selects scan speed as follows 16
- 5 cw fsk narrow filter this item selects the passband width for cw a1a fsk or j2b mode 16
- 6 fsk shift frequency several shift frequencies the difference between the mark and space frequency are used for fsk opera tion this item allows you to select a shift frequency for almost any fsk system 16
- 7 fsk polarity normal and reverse polarities are available for fsk operation this item allows you to select one of these polarities 16
- 8 cw break in the cw break in function in a1a mode toggles transmit and receive with cw keying full break in al lows you to receive signals between transmitted key ing pulses during cw transmission semi break in allows you to mute receiving until keying stops with some delay time 16
- Fk rev off normal key open mark key close space 16
- Fk rev on reverse key open space key close mark 16
- Note when on is selected without optional fil ter installation the transceiver does not function in these modes 16
- Set mode 16
- Unit sec ch faster slower 16
- 14 group b channel inhibit this item allow you to set the number of usable chan nels in channel group b up to a maximum of 50 channels 18
- 15 group c channel inhibit this item allow you to set the number of usable chan nels in channel group c up to a maximum of 50 channels 18
- Set mode 18
- Connections and installation 19
- I connections on rear panel 19
- I unpacking 19
- R caution 19
- Connections and installation 20
- I connector information 20
- Specifications 20
- Connections and installation 21
- Specifications 21
- I ground connection 22
- I power source 22
- At 130 23
- Coaxial cable 23
- Connections and installation 23
- Control cable sold separately an optional opc 566 is available 23
- D at 130 automatic antenna tuner 23
- D mn 100 mn 100l antenna matchers 23
- D non icom tuner 23
- I antenna 23
- Ic m700pro 23
- Most stations operate with a whip or long wire insu lated backstay antenna however these antennas cannot be connected directly to the transceiver since their impedance may not be matched with the trans ceiver antenna connector 23
- Some non icom tuners may be used with the ic m700pro please consult your dealer or marina if you wish to connect one the following internal set tings may be required for connection 23
- To antenna element 23
- With a 50 ω matched antenna all marine bands can not be used the following antenna matcher or an tenna tuner may be helpful for antenna installation 23
- D mounting example 24
- D mounting location 24
- D transceiver dimensions 24
- I mounting 24
- Warning 24
- D installing an optional filter and alarm unit 25
- D opening the case 25
- I fuse replacement 25
- I installing internal options 25
- Display 26
- Problem possible cause solution ref 26
- Receive 26
- Transmit 26
- Troubleshooting 26
- What appears to be equipment malfunction may not be damaging or difficult to solve check the following chart before making any adjustments or sending the trans ceiver to an icom service center 26
- General 27
- I options 27
- I specifications 27
- Receiver 27
- Specifications and options 27
- Transmitter 27
- 1 32 kamiminami hirano ku osaka 547 0003 japan 28
- Count on us 28
Похожие устройства
- Bosch KGV36VL20R Инструкция по эксплуатации
- Asko HI1621G EU INDUCTION HOB Инструкция по эксплуатации
- Icom IC-M710 Инструкция по эксплуатации
- Bosch KGV39VW20R Инструкция по эксплуатации
- Asko HI1641S EU INDUCTION HOB Инструкция по эксплуатации
- Icom IC-M59 Инструкция по эксплуатации
- Bosch KGV39VL20R Инструкция по эксплуатации
- Asko HI1642S EU INDUCTION Инструкция по эксплуатации
- Icom IC-M80 Инструкция по эксплуатации
- Asko HI1661S EU INDUCTION HOB Инструкция по эксплуатации
- Bosch KGE36AL20R Инструкция по эксплуатации
- Icom IC-GM1500 Инструкция по эксплуатации
- Asko HI1662S INDUCTION Инструкция по эксплуатации
- Indesit IBFY 201 Инструкция по эксплуатации
- Icom IC-M302 Инструкция по эксплуатации
- Asko HI1861S EU INDUCTION HOB Инструкция по эксплуатации
- Bosch KGS39XL20R Инструкция по эксплуатации
- Icom IC-M402 Инструкция по эксплуатации
- Asko HI1862S INDUCTION Инструкция по эксплуатации
- Bosch KGV36XW20R Инструкция по эксплуатации