Makita DWR180RF [7/56] Assembly

7 ENGLISH

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch lever actuates properly and returns to the

"OFF" position when released.

To start the tool, simply pull the switch lever. Tool speed

is increased by increasing pressure on the switch lever.

Release the switch lever to stop.

► Fig.3: 1. Switch lever

NOTE: The tool automatically stops when you keep

pulling the switch trigger for about 1 minute.

To prevent the switch lever from accidentally pulled, the

lock lever is provided.

When the lock lever is in the lock position

, the switch

lever cannot be actuated.

When the lock lever is in the unlock position , the

switch lever can be actuated.

► Fig.4: 1. Lock lever 2. Lock 3. Unlock

CAUTION: When not operating the tool,

always slide the lock lever to the lock position .

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pull the switch lever to light up the lamp. The lamp

keeps on lighting while the switch lever is being pulled.

The light automatically goes out approximately 10 sec-

onds after the switch lever is released.

► Fig.5: 1. Switch lever 2. Lamp

NOTICE: When the tool is overheated, the lamp

blinks. Cool down the tool fully before operating the

tool again.

NOTICE: Use a dry cloth to wipe the dirt o󰀨 the lens

of the lamp. Be careful not to scratch the lens of lamp,

or it may lower the illumination.

Reversing lever action

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing lever only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

This tool has a reversing lever to change the direction

of rotation. Turn the reversing lever to the A side for

clockwise rotation or to the B side for counterclockwise

rotation.

Make sure that the reversing lever is fully turned with

a click.

► Fig.6: 1. Reversing lever

ASSEMBLY

CAUTION: Always be sure that the tool is

switched o󰀨 and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing socket

adaptor

To install the socket adaptor, push it into the adaptor

hole until it locks into place.

► Fig.7: 1. Socket adaptor 2. Adaptor hole

To remove the socket adaptor, insert a stick like a

screwdriver into the backside of the socket adaptor, and

then tap it gently.

► Fig.8: 1. Socket adaptor 2. Screwdriver

NOTICE: During removal procedure, keep holding

the socket adaptor to prevent it from falling o󰀨 from

the tool.

Installing or removing socket

CAUTION: Before operation, make sure that

the socket is properly locked onto the socket

adaptor. Incomplete attachment of the socket may

cause injury.

NOTICE: Always use the correct size socket for bolt/

nut. An incorrect size socket will result in inconsistent

fastening torque and/or damage to the bolt/nut.

To install the socket, push it onto the socket adaptor

until it locks into place. To remove the socket, simply

pull it o󰀨.

► Fig.9: 1. Socket 2. Socket adaptor

OPERATION

CAUTION: Hold the tool rmly especially

when the bolt/nut reaches the seating position.

The socket stops rotating and the motor reaction

generate instant backlash to rotate the tool.

NOTICE: Hold the tool pointed straight at the

bolt/nut.

Hold the tool rmly and place the socket over the

bolt/nut. Turn the tool on and fasten. When the bolt/

nut reaches the seating position, the tool stops

automatically.

► Fig.10

The tool also works without socket. The adaptor hole

can fasten M8 (5/16") bolt/nut. (works as 13mm socket)

► Fig.11

Makita DWR180RF [7/56] Assembly

Содержание

Похожие устройства