Candy PC PVTP640SN [7/28] Instructions for the user
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Candy PC PVTP640SN [7/28] Instructions for the user

Candy PC PVTP640SN [7/28] Instructions for the user
7
INSTRUCTIONS FOR THE USER
USING THE BURNERS
The symbols silk-screen printed on the side of the
knob indicate the correspondence between the
knob and the burner.
Start-up without valves
Turn the corresponding knob anticlockwise up to
the maximum position (large flame, fig. 1) and
press start-up button P (fig.1).
Automatic start-up with valves
Turn the corresponding knob anticlockwise up to
the maximum position (large flame, fig. 1) and
press the knob.
Once the burner has been started up, keep the
knob pressed for about 6 seconds.
Using the burners
In order to obtain the maximum yield without waste
of gas, it is important that the diameter of the pot is
suitable for the burner potential (see the following
table), so as to avoid that the flame goes out of the
pot bottom (fig. 2).
Use the maximum capacity to quickly make the
liquids reach the boiling temperature, and the
reduced capacity to heat food or maintain boiling.
All of the operating positions must be chosen
between the maximum and the minimum ones,
never between the minimum position and the
closing point.
The gas supply can be interrupted by turning the
knob clockwise up to the closing position.
If there is no power supply, it is possible to light the
burners with matches, setting the knob to the start-
up point (large flame, fig. 1).
Notice
-When the equipment is not working, always check
that the knobs are in the closing position (see
fig.1).
- If the flame should blow out accidentally, the
safety valve will automatically stop the gas supply,
after a few seconds. To restore operation, set the
knob to the lighting point (large flame, fig. 1).
-While cooking with fat or oil, pay the utmost
attention as these substances can catch fire when
overheated.
-Do not use sprays near the appliance in
operation.
-Do not place unstable or deformed pots on the
burner, so as to prevent them from overturning or
overflowing.
-Make sure that pot handles are placed properly.
-When the burner is started up, check that the
flame is regular and, before taking pots away,
always lower the flame or put it out.
CLEANING
Before any operation, disconnect the appliance
from the electric grid.
It is advisable to clean the appliance when it is
cold.
Glass platform and enamelled parts
The glass platform and all of the enamelled parts
must be washed with a sponge and soapy water or
with a light detergent.
Do not use abrasive or corrosive products.
Do not leave substances, such as lemon or tomato
juice, salt water, vinegar, coffee and milk on the
enamelled surfaces for a long time.
Burners and racks
These parts can be removed to make cleaning
easier.
The burners must be washed with a sponge and
soapy water or with a light detergent, wiped well
and placed in their housing perfectly. Make sure
that the flame-dividing ducts are not clogged.
Check that the feeler of the safety valve and the
start-up electrode are always perfectly cleaned, so
as to ensure an optimum operation.
The racks can be washed in the dishwasher.
Gas taps
The possible lubrication of the taps must be carried
out by specialized personnel, exclusively.
In case of hardening or malfunctions in the gas
taps, apply to the Customer Service.
Burners Power W Ø of pots
Auxiliary 1000 10 - 14 cm
Semi-rapid 1650 16 - 18 cm
Rapid 3000 20 - 22 cm
Tr iple ring 3300 24 - 26 cm
It is necessary that all the operations regarding the installation, adjustment and
adaptation to the type of gas available are carried out by qualified personnel, in
conformity with the regulations in force.
The specific instructions are described in the booklet section intended for the installer.

Содержание

Похожие устройства

Скачать