Flex LD 18-7 150 R, Kit Turbo-Jet [15/224] Safety instructions a

Flex LD 18-7 150 R, Kit Turbo-Jet [15/224] Safety instructions a
LD 18-7 125 R/LD 18-7 150 R
15
Safety instructions
t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåë K=
c~áäìêÉ=íç=çÄëÉêîÉ=íÜÉ=ë~ÑÉíó=
áåëíêìÅíáçåë=~åÇ=çíÜÉê=áåëíêìÅíáçåë=ã~ó=êÉëìäí=
áå=~å=ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ=~åÇLçê=ëÉêáçìë=
áåàìêáÉë
K=hÉÉé=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=
çíÜÉê=áåëíêìÅíáçåë=áå=~=ë~ÑÉ=éä~ÅÉ=Ñçê=íÜÉ=
ÑìíìêÉK
This electric power tool must be used
as a sander. Read all safety warnings,
instructions, illustrations and speci-
fications provided with this power tool.
Failure to follow all instructions listed
below may result in electric shock,
fire and/or serious injury.
Operations such as sanding, wire
brushing, or for polishing and cut-off
are not recommended to be performed
with this power tool.
Operations for which the power tool was
not designed may create a hazard and
cause personal injury.
Do not use accessories which are not
specifically designed and recommen-
ded by the tool manufacturer.
Just because the accessory can be
attached to your power tool, it does
not assure safe operation.
The rated speed of the accessory must
be at least equal to the maximum
speed marked on the power tool.
Accessories running faster than their rated
speed can break and fly apart.
The outside diameter and the thickness
of your accessory must be within the
capacity rating of your power tool.
Incorrectly measured insertion tools
cannot be adequately shielded or con-
trolled.
Sanding discs, sanding pads or other
accessories must fit exactly on
the grinding spindle of your electric
power tool.
Insertion tools, which do not fit exactly
on the grinding spindle of the electric
power tool, rotate unevenly, vibrate
violently and may result in loss of control.
Do not use a damaged accessory.
Before use, always check insertion
tools for splinters and cracks, sanding
pad for cracks, wear and severe
abrasion. If power tool or accessory
is dropped, inspect for damage
or install an undamaged accessory.
After inspecting and installing an
accessory, position yourself and
bystanders away from the plane
of the rotating accessory and run
the power tool at maximum no-load
speed for one minute.
Damaged accessories will normally break
apart during this test time.
Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety
glasses. If appropriate, wear a dust
mask, hearing protection, protective
gloves and/or a special apron which
protect you from small sanding and
material particles.
The eye protection must be capable
of stopping flying debris generated by
various operations. The dust mask or
respirator must be capable of filtrating
particles generated by your operation.
Prolonged exposure to high intensity
noise may cause hearing loss.

Содержание

en LD 18 7 125 R LD 18 7 150 R Safety instructions A WARNING Read all safety instructions and other instructions Failure to observe the safety instructions and other instructions may result in an electric shock fire and or serious injuries Keep all safety instructions and other instructions in a safe place for the future This electric power tool must be used as a sander Read all safety warnings instructions illustrations and speci fications provided with this power tool Failure to follow all instructions listed below may result in electric shock fire and or serious injury Operations such as sanding wire brushing or for polishing and cut off are not recommended to be performed with this power tool Operations for which the power tool was not designed may create a hazard and cause personal injury Do not use accessories which are not specifically designed and recommen ded by the tool manufacturer Just because the accessory can be attached to your power tool it does not assure safe operation The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool Accessories running faster than their rated speed can break and fly apart The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool Incorrectly measured insertion tools cannot be adequately shielded or con trolled Sanding discs sanding pads or other accessories must fit exactly on the grinding spindle of your electric power tool Insertion tools which do not fit exactly on the grinding spindle of the electric power tool rotate unevenly vibrate violently and may result in loss of control Do not use a damaged accessory Before use always check insertion tools for splinters and cracks sanding pad for cracks wear and severe abrasion If power tool or accessory is dropped inspect for damage or install an undamaged accessory After inspecting and installing an accessory position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no load speed for one minute Damaged accessories will normally break apart during this test time Wear personal protective equipment Depending on application use face shield safety goggles or safety glasses If appropriate wear a dust mask hearing protection protective gloves and or a special apron which protect you from small sanding and material particles The eye protection must be capable of stopping flying debris generated by various operations The dust mask or respirator must be capable of filtrating particles generated by your operation Prolonged exposure to high intensity noise may cause hearing loss 15

Скачать