![Nissan Note [3/62] Precautions](/img/pdf.png)
Nissan Note [3/62] Precautions
![Nissan Note [3/62] Precautions](/views2/1789831/page3/bg3.png)
PRECAUTIONS
SRS-3
C
D
E
F
G
I
J
K
L
M
A
B
SRS
PRECAUTIONS PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
BHS0002S
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
● To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
● Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
● Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
BHS0002T
● Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
● Before servicing the SRS, turn ignition switch “OFF”, disconnect battery ground cable and wait at least 3
minutes.
For approximately 3 minutes after the cables is removed, it is still possible for the air bag and seat belt
pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes
have passed.
● Diagnosis sensor unit must always be installed with their arrow marks “⇐” pointing towards the front of the
vehicle for proper operation. Also check diagnosis sensor unit for cracks, deformities or rust before instal-
lation and replace as required.
● The spiral cable must be aligned with the neutral position since its rotations are limited. Do not attempt to
turn steering wheel or column after removal of steering gear.
● Handle air bag module carefully. Always place driver and front passenger air bag modules with the pad
side facing upward and place front side air bag module standing with stud bolt side setting bottom.
● Conduct self-diagnosis to check entire SRS for proper function after replacing any components.
● After air bag inflates, the front instrument panel assembly should be replaced if damaged.
Содержание
- Contents 1
- H restraints 1
- Sectio 1
- Supplemental restraint system srs 1
- Precautions 3
- Precautions for srs air bag and seat belt pre tensioner service 3
- Precautions for supplemental restraint system srs air bag and seat belt pre tensioner 3
- Commercial service tools 4
- Preparation 4
- Special service tools 4
- Srs configuration 5
- Supplemental restraint system srs 5
- The air bag deploys if the diagnosis sensor unit activates while the ignition switch is in the on or start posi tion the collision modes for which supplemental restraint systems are activated are different among the srs sys tems for example the driver air bag module and front passenger air bag module are activated in a frontal col lision but not in a side collision srs configurations which are activated for some collision modes are as follows 5
- Front passenger air bag cut off switch 6
- Front seat belt pre tensioner with load limiter 6
- Front side air bag 6
- Side curtain air bag 6
- Supplemental restraint system srs 6
- Air bag off indicator 1 7
- Front passenger air bag off indicator 7
- Supplemental restraint system srs 7
- The front passenger air bag off indicator is arranged in the a c control panel 7
- Diagnosis function 8
- How to perform trouble diagnoses for quick and accurate repair 8
- Information from customer 8
- Preliminary check 8
- Trouble diagnosis 8
- Trouble diagnosis introduction 8
- Trouble diagnosis 9
- Work flow 9
- Component parts location 10
- Srs 10 10
- Trouble diagnosis 10
- Schematic 11
- Srs 11 11
- Trouble diagnosis 11
- Srs 13 13
- Trouble diagnosis 13
- Srs 15 15
- Trouble diagnosis 15
- Consult ii function 16
- Diagnosis mode for consult ii 16
- From diagnosis mode to user mode 16
- How to change self diagnosis mode with consult ii from user mode to diagnosis mode 16
- Srs 16 16
- Trouble diagnosis 16
- How to change self diagnosis mode without consult ii 17
- How to erase self diagnosis results 17
- Self diagnosis function without consult ii 17
- Srs 17 17
- Trouble diagnosis 17
- Diagnostic procedure 1 checking air bag operation by using air bag warning lamp user mode 18
- Srs 18 18
- Srs operation check 18
- Trouble diagnosis 18
- Srs 19 19
- Trouble diagnosis 19
- Warning lamp examples 19
- Diagnostic procedure 2 20
- Srs 20 20
- Trouble diagnosis 20
- Trouble diagnosis with consult ii 20
- Consult ii diagnostic code chart self diag current 21
- Srs 21 21
- Trouble diagnosis 21
- Srs 22 22
- Trouble diagnosis 22
- Note follow the procedures in numerical order when repairing malfunctioning parts confirm whether malfunction is eliminated using air bag warning lamp or consult ii each time repair is finished if malfunction is still observed proceed to the next step when malfunction is eliminated further repair work is not required 23
- Srs 23 23
- Trouble diagnosis 23
- Diagnostic procedure 3 24
- Srs 24 24
- Trouble diagnosis 24
- Check that no malfunction is detected on self diag past 5 touch back key of consult ii until select system appears in order to return to user mode from diagnosis mode 6 turn ignition switch off then turn off and disconnect con sult ii go to srs 18 checking air bag operation by using air bag warning lamp user mode 25
- Srs 25 25
- Trouble diagnosis 25
- Diagnostic procedure 4 continued from diagnostic procedure 2 26
- Diagnostic procedure 5 26
- Srs 26 26
- Trouble diagnosis 26
- Consult ii diagnostic code chart self diag past or trouble diag record 27
- Diagnostic code is displayed on trouble diag record 5 touch print 6 compare diagnostic codes to srs 27 consult ii diagnostic code chart self diag past or trouble diag 27
- Record 7 touch back key of consult ii until select system appears 8 turn ignition switch off then turn off and disconnect con sult ii and both battery cables 9 repair the system as outlined by the repair order in intermit tent malfunction diagnostic code chart that corresponds to the self diagnostic result for replacement procedure of component parts refer to the removal and installa tion procedure for the appropriate component 10 go to srs 24 diagnostic procedure 3 for final checking 27
- Srs 27 27
- Touch trouble diag record note with trouble diag record diagnosis results previously erased by a reset operation can be displayed 27
- Trouble diagnosis 27
- Srs 28 28
- Trouble diagnosis 28
- Srs 29 29
- Trouble diagnosis 29
- Diagnostic procedure 6 inspecting srs malfunctioning parts by using air bag warning lamp diagnosis mode 30
- Srs 30 30
- Trouble diagnosis 30
- Trouble diagnosis without consult ii 30
- Warning lamp flash code chart 30
- Srs 31 31
- Trouble diagnosis 31
- Srs 32 32
- Trouble diagnosis 32
- Srs 33 33
- Trouble diagnosis 33
- Diagnostic procedure 7 34
- Srs 34 34
- Trouble diagnosis 34
- Trouble diagnosis air bag warning lamp does not turn off 34
- Diagnostic procedure 8 35
- Srs 35 35
- Trouble diagnosis 35
- Trouble diagnosis air bag warning lamp does not turn on 35
- Driver air bag module 36
- Removal 36
- Removal and installation 36
- Srs 36 36
- Driver air bag module 37
- Installation 37
- Srs 37 37
- Removal 38
- Removal and installation 38
- Spiral cable 38
- Srs 38 38
- Installation 39
- Spiral cable 39
- Srs 39 39
- Front passenger air bag module 40
- Removal 40
- Removal and installation 40
- Srs 40 40
- Front passenger air bag module 41
- Installation 41
- Srs 41 41
- Front side air bag module 42
- Removal 42
- Removal and installation 42
- Srs 42 42
- After the work is completed perform self diagnosis to make sure that no malfunction is detected refer to srs 18 srs operation check 43
- Always work from the side of or under front side air bag module 43
- Do not use air tools or electric tools for servicing 43
- Front side air bag module 43
- Install in the reverse order of removal caution 43
- Installation 43
- Srs 43 43
- Installation 44
- Removal 44
- Removal and installation 44
- Side curtain air bag module 44
- Srs 44 44
- Crash zone sensor 45
- Installation 45
- Removal 45
- Removal and installation 45
- Srs 45 45
- Installation 46
- Removal 46
- Removal and installation 46
- Side air bag satellite sensor 46
- Srs 46 46
- For removal and installation procedures refer to sb 3 removal and installation of front seat belt 47
- Removal and installation 47
- Seat belt pre tensioner 47
- Srs 47 47
- Diagnosis sensor unit 48
- Ecu discriminated no 48
- Installation 48
- Removal 48
- Removal and installation 48
- Srs 48 48
- Caution for air bag module and seat belt pre tensioner 49
- Checking deployment tool connecting to battery 49
- Deployment tool check 49
- Disposal of air bag module and seat belt pre tensioner 49
- Srs 49 49
- Air bag deployment tool lamp illumination chart battery connected 50
- Disposal of air bag module and seat belt pre tensioner 50
- Srs 50 50
- Disposal of air bag module and seat belt pre tensioner 51
- Srs 51 51
- Disposal of air bag module and seat belt pre tensioner 52
- Srs 52 52
- Disposal of air bag module and seat belt pre tensioner 53
- Srs 53 53
- Disposal of air bag module and seat belt pre tensioner 54
- Srs 54 54
- Deployment procedures for front seat belt pre tensioner 2 outside of vehicle 55
- Disposal of air bag module and seat belt pre tensioner 55
- Srs 55 55
- Disposal of air bag module and seat belt pre tensioner 56
- Srs 56 56
- Deployment of air bag module and seat belt pre tensioner while mounted in vehicle 57
- Disposal of air bag module and seat belt pre tensioner 57
- Disposing of air bag module and seat belt pre tensioner 57
- Srs 57 57
- Collision diagnosis 58
- For frontal collision 58
- Replace any srs components showing visible signs of damage dents cracks and deformation 2 conduct self diagnosis using consult ii or air bag warning lamp refer to srs 18 srs operation check for details ensure entire srs operates properly 58
- Replace any srs components showing visible signs of damage dents cracks and deformation 4 install new air bag modules except the front side air bag modules and side curtain air bag modules crash zone sensor assembly bracket and seat belt pre tensioner assemblies 5 conduct self diagnosis using consult ii or air bag warning lamp refer to srs 18 srs operation check for details ensure entire srs operates properly when srs is not activated in a collision 1 check the srs components using the table below 58
- Srs 58 58
- Srs inspection for frontal collision 58
- To repair the srs perform the following steps when srs except the front side air bag and side curtain air bag modules is activated in a collision 1 replace the diagnosis sensor unit 2 remove the air bag modules except the front side air bag modules and side curtain air bag modules crash zone sensor assembly bracket and seat belt pre tensioner assemblies 3 check the srs components using the table below 58
- Collision diagnosis 59
- Srs 59 59
- All parts of front seatback including front seatback frame with front side air bag module on the side on which front side air bag is activated 60
- Check the srs components and the related parts using the following table 60
- Collision diagnosis 60
- Curtain air bag module on the side on which side curtain air bag is activated 60
- Diagnosis sensor unit 60
- For side collision 60
- Replace any srs components and the related parts showing visible signs of damage dents cracks deformation 2 conduct self diagnosis using consult ii or air bag warning lamp refer to srs 18 srs operation check ensure entire srs operates properly 60
- Replace any srs components and the related parts showing visible signs of damage dents cracks deformation 3 conduct self diagnosis using consult ii or air bag warning lamp refer to srs 18 srs operation check ensure entire srs operates properly 60
- Replace the following components 60
- Satellite sensor on the side on which side air bag and side curtain air bag is activated 2 check the srs components and the related parts using the following table 60
- Srs 60 60
- Srs inspection for side collision 60
- When srs is not activated in the side collision 60
- When the side air bag is activated in the side collision 60
- Collision diagnosis 61
- Srs 61 61
Похожие устройства
- Nissan Note STARTING _ CHARGING SYSTEM
- Nissan Note POWER SUPPLY, GROUND _ CIRCUIT ELEMENTS
- Nissan Note ROAD WHEELS _ TYRES
- Nissan Note WIPER, WASHER _ HORN
- Daikin BRC1H81S7 Инструкция по эксплуатации
- Daikin BRC1H81S7 Руководство по применению для установщика
- Daikin BRC1H82W Инструкция по эксплуатации
- Daikin BRC1H82W Руководство по применению для установщика
- Daikin BRC1H82K Инструкция по эксплуатации
- Daikin BRC1H82K Руководство по применению для установщика
- Daikin BRC1H82S Инструкция по эксплуатации
- Daikin BRC1H82S Руководство по применению для установщика
- Daikin BS4Q14AV1 Инструкция по монтажу
- Daikin BS6Q14AV1 Инструкция по монтажу
- Daikin BS8Q14AV1 Инструкция по монтажу
- Daikin BS10Q14AV1 Инструкция по монтажу
- Daikin BS12Q14AV1 Инструкция по монтажу
- Daikin BS16Q14AV1 Инструкция по монтажу
- Daikin BS4Q14AV1B Инструкция по монтажу
- Daikin BS6Q14AV1B Инструкция по монтажу
Скачать
Случайные обсуждения