Comet FDX Blade XL PRO 9.16 16/200 G Honda GX270 ZWD [25/180] Special maintenance

Comet FDX Blade XL PRO 13.15 15/280 G Loncin G390F FW2 [25/180] Special maintenance
25
MAINTENANCE
SCHEDULE
JOB
Weekly
(FDX ENDURANCE)
Clean the water inlet lter(23).
Turn the ring nut(62) anticlockwise until it is completely undone; take the lter
cartridge (63) out and clean it as explained above; in the case of truly stubborn dirt
change the cartridge, contacting a Specialized Technician for the right cartridge
to use; put the cartridge back in place and close the lter, turning the ring nut (62)
clockwise.
Monthly Clean the water inlet lter(45) - (23) - (39) (refer to what has been explained
previously).
Clean the detergent suction lter(40).
It is normally enough to put the filter under running water or blow it with
compressed air to clean it. In the most dicult cases use a scale remover or replace
it, contacting an authorised assistance centre to buy the new lter.
Clean the nozzle.
It is normally enough to put the needle (29) supplied through the hole of the
nozzle to clean it. If the results are not good, replace the nozzle purchasing it from
an authorised assistance centre.
The professional xed fan nozzle mounted on the nozzle holder heads (24) and
spray gun(19) can be replaced using a 14 mm box spanner (not supplied).
Oil or grease the rotating or sliding parts the operator is able to reach (refer also to
the engine operating and maintenance manual).
Check soundness of the water inlet and outlet circuits.
Check tyre ination pressure.
Check clamping of the pump to the engine and the engine to the frame.
If clamping is found to be insecure do not, under any circumstances, use the
high pressure cleaner and contact a Specialized Technician.
CAUTION
When working, the high pressure cleaner should not be too noisy and there should be no obvious
drips of water or oil underneath it. If this is the case have the machine checked by a Specialized
Technician.
SPECIAL MAINTENANCE
Special maintenance must only be done by a Specialized Technician, complying with the following table.
Also remember to carry out the special maintenance jobs listed in the engine operating and maintenance
manual.
MAINTENANCE
SCHEDULE
JOB
After the rst 50hours of
operation
Change pump oil.
Every 200 hours
Check the pump’s hydraulic circuit.
Check pump and engine clamping.
Every 500 hours
Change pump oil and gearbox oil.
Check the pump suction/delivery valves.
Check tightness of pump screws.
Check the pump regulation valve.
Check the safety devices.
CAUTION
The data given in the table are approximate. It might be necessary to carry out maintenance more
frequently in the case of particularly heavy work.
EN

Содержание

MAINTENANCE JOB SCHEDULE Weekly FDX ENDURANCE Clean the water inlet filter 23 Turn the ring nut 62 anticlockwise until it is completely undone take the filter cartridge 63 out and clean it as explained above in the case oftruly stubborn dirt change the cartridge contacting a SpecializedTechnician for the right cartridge to use put the cartridge back in place and close the filter turning the ring nut 62 clockwise Monthly Clean the water inlet filter 45 23 39 refer to what has been explained previously Clean the detergent suction filter 40 It is normally enough to put the filter under running water or blow it with compressed air to clean it In the most difficult cases use a scale remover or replace it contacting an authorised assistance centre to buy the new filter Clean the nozzle It is normally enough to put the needle 29 supplied through the hole of the nozzle to clean it If the results are not good replace the nozzle purchasing it from an authorised assistance centre The professional fixed fan nozzle mounted on the nozzle holder heads 24 and spray gun 19 can be replaced using a 14 mm box spanner not supplied Oil or grease the rotating or sliding parts the operator is able to reach refer also to the engine operating and maintenance manual Check soundness of the water inlet and outlet circuits Check tyre inflation pressure Check clamping of the pump to the engine and the engine to the frame If clamping is found to be insecure do not under any circumstances use the high pressure cleaner and contact a Specialized Technician CAUTION When working the high pressure cleaner should not be too noisy and there should be no obvious drips of water or oil underneath it If this is the case have the machine checked by a Specialized Technician SPECIAL MAINTENANCE Special maintenance must only be done by a SpecializedTechnician complying with thefollowing table Also rememberto carry outthe special maintenance jobs listed in theengine operating and maintenance manual MAINTENANCE JOB SCHEDULE After the first 50 hours of operation Change pump oil Every 200 hours Check the pump s hydraulic circuit Check pump and engine clamping Every 500 hours Change pump oil and gearbox oil Check the pump suction deli very valves Check tightness of pump screws Check the pump regulation valve Check the safety devices CAUTION The data given in the table are approximate It might be necessary to carry out maintenance more frequently in the case of particularly heavy work 25

Скачать