![Hitachi G12SE2 [6/45] English](/img/pdf.png)
Hitachi G12SE2 [6/45] English
![Hitachi G13SE2-NS [6/45] English](/views2/1081293/page6/bg6.png)
5
English
SPECIFICATIONS
*Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Depressed center wheel ..........................................1
(2) Wrench ........................................................................1
(3) Side handle ................................................................1
Standard accessories are subject to change without
notice.
APPLICATIONS
䡬 Removal of casting fin and finishing of various
types of steel, bronze and aluminum materials and
castings.
䡬 Grinding of welded sections or sections cut by
means of a cutting torch.
䡬 Grinding of synthetic resins, slate, brick, marble, etc.
䡬 Cutting of synthetic concrete, stone, brick, marble,
and similar materials.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Fitting and adjusting the wheel guard
The wheel guard is a protective device to prevent
injury should the depressed center wheel be
shattered during operation. Ensure that the wheel
guard is properly fitted and fastened before
commencing grinding operation.
[How to attach and adjust the wheel guard](Fig. 2)
䡬 Set the wheel ass’y to the packing gland.
䡬 Tighten M5 screw to secure the wheel guard while
the lever is in closed position.
䡬 Perform the adjustment of the wheel guard while
the lever is released. (Loosen M5 screw and readjust
if the wheel guard does not rotate smoothly.)
䡬 After adjustment, if grinder operation is required,
perform the operation only after setting the lever
in closed position.
䡬 Lubricate the sliding section of the set piece (B) and
the lever if the lever does not move smoothly.
5. Ensure that mounted wheels and points are fitted
in accordance with the manufacturer’s instructions.
Ensure that the depressed center wheel to be utilized
is the correct type and free of cracks or surface
defects. Also ensure that the depressed center wheel
is properly mounted and the wheel nut is securely
tightened, Refer to the section on “Depressed Center
Wheel Assembly”
Ensure that blotters are used when they are provided
with the bonded abrasive product and when they
are required.
Do not use separate reducing bushings or adaptors
to adapt large hole abrasive wheels.
For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
Do not use cutting off wheel for side grinding.
Model G12SE2 G13SE2
Voltage (by areas)* (110V, 120V, 230V, 240V)
Power Input* 1200 W
No-load speed* 11000 min
-1
Wheel
outer dia. × hole dia. 115 × 22 mm 125 × 22 mm
peripheral speed 80 m/s
Weight (only main body) 1.9 kg
PRECAUTIONS ON USING DISC GRINDER
1. Never operate these power tools without Wheel
Guards.
2. Check that speed marked on the wheel is equal to
or greater than the rated speed of the grinder.
Use only depressed center wheels rated at 80m/s
or more.
3. Ensure that the wheel dimensions are compatible
with the grinder and that the wheel fits the spindle.
4. Abrasive wheels shall be stored and handled with
care in accordance with manufacturer’s instructions.
5. Inspect the depressed center wheel before use, do
not use chipped, cracked or otherwise defective
products.
6. Always hold the body handle and side handle of
the power tool firmly. Otherwise the counterforce
produced may result in inaccurate and even
dangerous operation.
7. Do not use cutting-off wheels for side grinding.
8. Do not use of separate reducing bushings or adapters
to adapt large hole abrasive wheels.
9. The wheel continues to rotate after the tool is
switched off.
Содержание
- Disc grinder winkelschleifer ˆóè îfi ùúô fi ïâè óû∠îô szlifierka kątowa sarokcsiszoló úhlová bruska taßlama ìöîoçaó åîëùoçaîëìaó ïaåëìa 1
- G 12se 1
- G 13se2 1
- Handling instructions bedienungsanleitung ëá â âèúèûìô instrukcja obsługi kezelési utasítás návod k obsluze kullanım talimatları àìcúpyíáëó ôo íícôîyaúaáëë 1
- English 5
- General safety rules 5
- Applications 6
- English 6
- Precautions on using disc grinder 6
- Prior to operation 6
- Specifications 6
- Standard accessories 6
- Assembling and disassembling the depressed center wheel fig 1 7
- English 7
- Maintenance and inspection 7
- Practical grinder application 7
- English 8
- Allgemeine sicherheitsmassnahmen 9
- Deutsch 9
- Anwendungsgebiete 10
- Deutsch 10
- Standardzubehör 10
- Technische daten 10
- Vorsichtsmassnahmen bei der benutzung des winkelschleifers 10
- Deutsch 11
- Praktische schleifarbeit 11
- Vor inbetriebnahme 11
- Anbringen und abnehmen der schleifscheibe abb 1 12
- Deutsch 12
- Wartung und inspektion 12
- Deutsch 13
- Ïïëóèî 14
- Π õ ª ƒ º π 14
- º ƒª 15
- Ã π ã ƒ ƒπ π 15
- Ïïëóèî 15
- Ƒ ºà π ª ƒ ø ムà π à π 15
- Π ƒ ª 15
- Ïïëóèî 16
- Ƒ π º ƒª à π 16
- Ƒπ π àƒ π 16
- À ƒ π ã 17
- À ƒª π à ƒª à ã ª øª à ƒπ ƒ ã à èî 1 17
- Ïïëóèî 17
- Ïïëóèî 18
- Ogólne wskazówki bezpieczeństwa 19
- Polski 19
- Dane techniczne 20
- Polski 20
- Przed użyciem 20
- Wyposażenie standardowe 20
- Zastosowanie 20
- Środki ostrożności przy używaniu szlifierki tarczowej 20
- Polski 21
- Praktyczne zastosowanie szlifierki 21
- Konserwacja i inspekcja 22
- Polski 22
- Składanie i rozkładanie obniżonych tarcz śsrodkowych rys 1 22
- Magyar 23
- Általános biztonságtechnikai e 23
- A tárcsás kéziköszörű használatára vonatkozó óvintézkedések 24
- Alkalmazások 24
- Az üzembehelyezés előtti tennivalók 24
- Magyar 24
- Műszaki adatok 24
- A kéziköszörű gyakorlati kezelése 25
- Magyar 25
- A süllyesztett közepű tárcsa összeszerelése és szétszerelése 1 ábra 26
- Ellenőrzés és karbantartás 26
- Magyar 26
- Všeobecné bezpečnostní předpisy 27
- Čeština 27
- Parametry 28
- Použití 28
- Před použitím 28
- Standardní příslušenství 28
- Upozornění pro používání kotoučové brusky 28
- Čeština 28
- Montáž a demontáž brusného kotouče obr 1 29
- Praktické použití brusky 29
- Údržba a kontrola 29
- Čeština 29
- Čeština 30
- Genel güvenlik kurallari 31
- Türkçe 31
- Aletó kullanim öncesónde 32
- Dósk taílama aletónó kullanirken alinacak önlemler 32
- Standart aksesuarlar 32
- Teknók özellókler 32
- Türkçe 32
- Uygulamalar 32
- Bakim ve ónceleme 33
- Pratók taílama uygulamalari 33
- Tek tarafi oyuk taílama dóskónón takilip çikarilmasi íekil 1 33
- Türkçe 33
- Türkçe 34
- Oåôàe èpabàãa èo texhàke åeâoèachoctà 35
- Pyccíëè 35
- Mepõ èpeñoctopoühoctà èpà ùkcèãìatañàà òãàîobaãúhoâ maòàhõ 36
- Pyccíëè 36
- Ctahñapthõe akceccìapõ 37
- Oåãactú èpàmehehàü 37
- Pyccíëè 37
- Texhàóeckàe xapaktepàctàkà 37
- Èoñéotobka k ùkcèãìatañàà 37
- Pyccíëè 38
- Èpaktàóeckoe èpàmehehàe òãàîobaãúhoâ maòàhõ 38
- Ìctahobka à chütàe òãàîobaãúhoéo kpìéa c ìtoèãehhõm ñehtpom pëc 1 38
- Pyccíëè 39
- Texhàóeckoe oåcãìüàbahàe à èpobepka 39
- G12se2 40
- G13se2 41
- Head office in japan 45
- Hitachi koki co ltd 45
- Hitachi power tools europe gmbh 45
- K kato board director 45
- Representative office in europe 45
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 45
- Siemensring 34 47877 willich 1 f r germany 45
Похожие устройства
- Hansa BHIW67377 Wh Инструкция по эксплуатации
- Tefal ULTIMATE AUTOCLEAN FV9430 Инструкция по эксплуатации
- Hotpoint-Ariston BCB 33 A F (RU) Инструкция по эксплуатации
- Hitachi G12SR3 Инструкция по эксплуатации
- Tefal ULTIMATE AUTOCLEAN FV9440 Инструкция по эксплуатации
- Electrolux ESF6210LOW Инструкция по эксплуатации
- Tefal ULTIMATE AUTOCLEAN FV9450 Инструкция по эксплуатации
- Hitachi G13SQ Инструкция по эксплуатации
- Hitachi G13SD Инструкция по эксплуатации
- Samsung ME73AR Инструкция по эксплуатации
- Tefal ULTIMATE AUTOCLEAN FV9447 Инструкция по эксплуатации
- Samsung ME711KR Инструкция по эксплуатации
- Hitachi G13SE2 Инструкция по эксплуатации
- LG ARNU09GSF12 Инструкция по эксплуатации
- Samsung ME712AR Инструкция по эксплуатации
- LG ARNU09GSF11 Инструкция по эксплуатации
- Hitachi G13SR3 Инструкция по эксплуатации
- LG ARNU09GSEV1 Инструкция по эксплуатации
- Hitachi G13SS Инструкция по эксплуатации
- Gorenje MO200MW Инструкция по эксплуатации
Скачать
Случайные обсуждения