![Hitachi G12SE2 [8/45] English](/img/pdf.png)
Hitachi G12SE2 [8/45] English
![Hitachi G12SE2 [8/45] English](/views2/1081293/page8/bg8.png)
7
English
3. Inspecting the carbon brushes (Fig. 5)
The Motor employs carbon brushes which are
consumable parts. When they become worn to or
near the “wear limit”, it could result in motor
trouble. When an auto-stop carbon brush is
equipped, the motor will stop automatically. At that
time, replace both carbon brushes with new ones
which have the same carbon brush Numbers shown
in the figure. In addition, always keep carbon brushes
clean and ensure that they slide freely within the
brush holders.
4. Replacing carbon brushes (Fig. 6)
〈
Disassembly
〉
(1) Loosen the D4 tapping screw retaining the tail cover
and remove the tail cover.
(2) Use the auxiliary hexagonal wrench or small
screwdriver to pull up the edge of the spring that
is holding down the carbon brush. Remove the
edge of the spring toward the outside of the brush
holder.
(3) Remove the end of the pig-tail on the carbon brush
from the terminal section of brush holder and then
remove the carbon brush form the brush holder.
〈
Assembly
〉
(1) Insert the end of the pig-tail of the carbon brush
in the terminal section of brush holder.
(2) Insert the carbon brush in the brush holder.
(3) Use the auxiliary hexagonal wrench or small
screwdriver to return the edge of the spring to the
head of the carbon brush.
(4) Mount the tail cover and tighten the D4 tapping
screw.
5. Maintenance of the motor
The motor unit winding is the very “heart” of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.
6. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION
Repair, modification and inspection of Hitachi Power
Tools must be carried out by an Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
NOTE
Due to HITACHI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
Information concerning airborne noise and vibration
The measured values were determined according to
EN 60745 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 95 dB (A)
Measured A-weighted sound pressure level: 84 dB (A)
Uncertainty KpA: 3 dB (A)
Wear ear protection.
The typical weighted root mean square acceleration
value does not exceed 2.5 m/s
2
.
Содержание
- Disc grinder winkelschleifer ˆóè îfi ùúô fi ïâè óû∠îô szlifierka kątowa sarokcsiszoló úhlová bruska taßlama ìöîoçaó åîëùoçaîëìaó ïaåëìa 1
- G 12se 1
- G 13se2 1
- Handling instructions bedienungsanleitung ëá â âèúèûìô instrukcja obsługi kezelési utasítás návod k obsluze kullanım talimatları àìcúpyíáëó ôo íícôîyaúaáëë 1
- English 5
- General safety rules 5
- Applications 6
- English 6
- Precautions on using disc grinder 6
- Prior to operation 6
- Specifications 6
- Standard accessories 6
- Assembling and disassembling the depressed center wheel fig 1 7
- English 7
- Maintenance and inspection 7
- Practical grinder application 7
- English 8
- Allgemeine sicherheitsmassnahmen 9
- Deutsch 9
- Anwendungsgebiete 10
- Deutsch 10
- Standardzubehör 10
- Technische daten 10
- Vorsichtsmassnahmen bei der benutzung des winkelschleifers 10
- Deutsch 11
- Praktische schleifarbeit 11
- Vor inbetriebnahme 11
- Anbringen und abnehmen der schleifscheibe abb 1 12
- Deutsch 12
- Wartung und inspektion 12
- Deutsch 13
- Ïïëóèî 14
- Π õ ª ƒ º π 14
- º ƒª 15
- Ã π ã ƒ ƒπ π 15
- Ïïëóèî 15
- Ƒ ºà π ª ƒ ø ムà π à π 15
- Π ƒ ª 15
- Ïïëóèî 16
- Ƒ π º ƒª à π 16
- Ƒπ π àƒ π 16
- À ƒ π ã 17
- À ƒª π à ƒª à ã ª øª à ƒπ ƒ ã à èî 1 17
- Ïïëóèî 17
- Ïïëóèî 18
- Ogólne wskazówki bezpieczeństwa 19
- Polski 19
- Dane techniczne 20
- Polski 20
- Przed użyciem 20
- Wyposażenie standardowe 20
- Zastosowanie 20
- Środki ostrożności przy używaniu szlifierki tarczowej 20
- Polski 21
- Praktyczne zastosowanie szlifierki 21
- Konserwacja i inspekcja 22
- Polski 22
- Składanie i rozkładanie obniżonych tarcz śsrodkowych rys 1 22
- Magyar 23
- Általános biztonságtechnikai e 23
- A tárcsás kéziköszörű használatára vonatkozó óvintézkedések 24
- Alkalmazások 24
- Az üzembehelyezés előtti tennivalók 24
- Magyar 24
- Műszaki adatok 24
- A kéziköszörű gyakorlati kezelése 25
- Magyar 25
- A süllyesztett közepű tárcsa összeszerelése és szétszerelése 1 ábra 26
- Ellenőrzés és karbantartás 26
- Magyar 26
- Všeobecné bezpečnostní předpisy 27
- Čeština 27
- Parametry 28
- Použití 28
- Před použitím 28
- Standardní příslušenství 28
- Upozornění pro používání kotoučové brusky 28
- Čeština 28
- Montáž a demontáž brusného kotouče obr 1 29
- Praktické použití brusky 29
- Údržba a kontrola 29
- Čeština 29
- Čeština 30
- Genel güvenlik kurallari 31
- Türkçe 31
- Aletó kullanim öncesónde 32
- Dósk taílama aletónó kullanirken alinacak önlemler 32
- Standart aksesuarlar 32
- Teknók özellókler 32
- Türkçe 32
- Uygulamalar 32
- Bakim ve ónceleme 33
- Pratók taílama uygulamalari 33
- Tek tarafi oyuk taílama dóskónón takilip çikarilmasi íekil 1 33
- Türkçe 33
- Türkçe 34
- Oåôàe èpabàãa èo texhàke åeâoèachoctà 35
- Pyccíëè 35
- Mepõ èpeñoctopoühoctà èpà ùkcèãìatañàà òãàîobaãúhoâ maòàhõ 36
- Pyccíëè 36
- Ctahñapthõe akceccìapõ 37
- Oåãactú èpàmehehàü 37
- Pyccíëè 37
- Texhàóeckàe xapaktepàctàkà 37
- Èoñéotobka k ùkcèãìatañàà 37
- Pyccíëè 38
- Èpaktàóeckoe èpàmehehàe òãàîobaãúhoâ maòàhõ 38
- Ìctahobka à chütàe òãàîobaãúhoéo kpìéa c ìtoèãehhõm ñehtpom pëc 1 38
- Pyccíëè 39
- Texhàóeckoe oåcãìüàbahàe à èpobepka 39
- G12se2 40
- G13se2 41
- Head office in japan 45
- Hitachi koki co ltd 45
- Hitachi power tools europe gmbh 45
- K kato board director 45
- Representative office in europe 45
- Shinagawa intercity tower a 15 1 konan 2 chome minato ku tokyo japan 45
- Siemensring 34 47877 willich 1 f r germany 45
Похожие устройства
- Hansa BHIW67377 Wh Инструкция по эксплуатации
- Tefal ULTIMATE AUTOCLEAN FV9430 Инструкция по эксплуатации
- Hotpoint-Ariston BCB 33 A F (RU) Инструкция по эксплуатации
- Hitachi G12SR3 Инструкция по эксплуатации
- Tefal ULTIMATE AUTOCLEAN FV9440 Инструкция по эксплуатации
- Electrolux ESF6210LOW Инструкция по эксплуатации
- Tefal ULTIMATE AUTOCLEAN FV9450 Инструкция по эксплуатации
- Hitachi G13SQ Инструкция по эксплуатации
- Hitachi G13SD Инструкция по эксплуатации
- Samsung ME73AR Инструкция по эксплуатации
- Tefal ULTIMATE AUTOCLEAN FV9447 Инструкция по эксплуатации
- Samsung ME711KR Инструкция по эксплуатации
- Hitachi G13SE2 Инструкция по эксплуатации
- LG ARNU09GSF12 Инструкция по эксплуатации
- Samsung ME712AR Инструкция по эксплуатации
- LG ARNU09GSF11 Инструкция по эксплуатации
- Hitachi G13SR3 Инструкция по эксплуатации
- LG ARNU09GSEV1 Инструкция по эксплуатации
- Hitachi G13SS Инструкция по эксплуатации
- Gorenje MO200MW Инструкция по эксплуатации
Скачать
Случайные обсуждения