![Haier HWD8040BW1 — решение проблем с работой стиральной машины [13/14]](/img/pdf.png)
Haier HWD8040BW1 — решение проблем с работой стиральной машины [13/14]
![Haier HWD8040BW1 [13/14] Machine is draining while being filled](/views2/1813885/page13/bgd.png)
2524
Troubleshooting Troubleshooting
In case of power failure
The current programme and its setting
will be saved.
Troubleshooting without display code
Problem Cause Solution
Washing machine
fails to operate
1. Power failure
2. Machine hasn’t been switched
on.
3. Door is not properly closed.
4. Programme is not yet. started
1. Check power supply.
2. Switch the machine on.
3. Close the door properly.
4. Touch “ Start /Pause”
button.
Washing machine
will not fill with
water.
1. No water inlet.
2. Inlet hose is kinked.
3. Inlet hose filter is blocked.
4. Water pressure is less than
0.03MPa.
5. Door is not properly closed.
6. Water supply failure.
1. Check water tap.
2. Check inlet hose.
3. Unblock inlet hose filter.
4. Check water pressure.
5. Close the door properly.
6. Ensure the water supply.
Machine is
draining while
being filled.
1. Height of drain hose is bel ow
80cm.
2. Drain hose end is submerged
1. Make sure that drain hose is
properly installed.
2. Make sure the drain hose is
not in water.
Drainage failure.
1. Drain hose is blocked.
2. Pump filter is blocked.
3. Drain hose end is higher than
100cm above floor level.
1. Unblock drain hose.
2. Clean pump filter.
3. Make sure that drain hose is
properly installed.
Problem Cause Solution
Strong vibration
while spinning.
1. Not all transportation bolts
have been removed.
2. Appliance has no solid
position.
3. Machine load is not balanced.
1. Remove all transportation
bolts.
2. Ensure solid ground and
a levelled position.
3. Check load weight and
balance.
Operation stops
for a period of
time.
1. Appliance displays error code.
2. Problem due to load pattern.
1. Consider display codes.
2. Reduce or adjust load.
3. Cancel programme and
restart.
Operation stops
before completi-
ng wash cycle.
Water or electric failure.
Check power and water
supply.
Excessive foam
floats drum and/or
detergent drawer.
1. Detergent is not a appropriate.
2. Excessive use of detergent in
manually dosage.
1. Check detergent recom-
mendations.
2. Reduce amount of dete-
rgent.
Spinning fails Unbalance of laundry. Check machine load.Run the
Spin programme again.
General information and tips:
If too much foam is visible during spin cycle, the motor will stop and drain
pump will activate for 90 seconds. If that elimination of foam fails up to 3
times, programme ends without spinning.
Automatic adjust-
ment
Washing programme
This is normal and doesn‘t
of washing
duration will be adjusted. affect functionality.
time
When power supply is restored, operation will be
resumed.
If a power failure cuts an operating wash programme，
door opening is mechanically blocked. To get out any
laundry，water level should not be seen in the glassy
porthole of the door. Danger of burns! Water level has
to be lowered as described in “Pump filter”. Not till then
pull level(A) beneath service flap until door as unlocked
by a gentle click. Afterwards refix all parts.
in water?
Содержание
- User manual washer dryer p.1
- Hwd8040bw1 p.1
- Consumption 15 p.2
- Care and cleaning 20 22 p.2
- Troubleshooting 23 25 p.2
- Thank you for purchasing a haier product thank you for purchasing a haier product p.2
- Technical data 26 p.2
- Safety and warnings 4 7 p.2
- Programmes 14 p.2
- Product description p.2
- Legend p.2
- Installation 8 9 p.2
- Disposal p.2
- Daily use 16 19 p.2
- Control panel 11 13 p.2
- Warning p.3
- Safety and warnings safety and warnings p.3
- Important safety instructions p.3
- Safety and warnings safety and warnings p.4
- Drain hose p.5
- Warning p.5
- Removing the transportation bolts p.5
- Preparation p.5
- Optional install noise reduction pads p.5
- Note packaging disposal p.5
- Installation p.5
- Inlet hose p.5
- General information and tips p.5
- Programme selector p.6
- Product description control panel p.6
- Power button p.6
- Detergent drawer p.6
- Accessories p.6
- Function buttons p.7
- Display p.7
- Control panel function buttons display symbols control panel p.7
- Note liquid detergent p.7
- Note factory settings p.7
- Wash dry p.8
- Programmes p.8
- Important p.8
- General information and tips p.8
- Eco 40 1400rpm is the program recommended for a normally soiled cotton load auto sense dry on is the program recommended for cotton loads p.8
- Detergent compartment for liquid detergent softener conditioning agent etc powder detergent p.8
- Consumption p.8
- Select a programme p.9
- Preparing laundry p.9
- Power supply p.9
- Loading the appliance p.9
- General information and tips p.9
- Daily use daily use p.9
- Adding detergent p.9
- Water connection p.9
- Warning p.9
- Selecting detergent p.9
- Start wash programme p.10
- Interrupt cancel wash programme p.10
- General information and tips p.10
- Daily use daily use p.10
- Care chart p.10
- After washing p.10
- Add individual selections p.10
- General information and tips p.11
- Cleaning the machine p.11
- Cleaning the drum p.11
- Cleaning the de tergent drawer p.11
- Care and cleaning care and cleaning p.11
- Care and cleaning troubleshooting p.12
- Water inlet valve and inlet valve filter p.12
- Display code p.12
- Choose the best detergent p.12
- The current programme and its setting will be saved p.13
- Strong vibration while spinning p.13
- Problem cause solution p.13
- Operation stops for a period of time p.13
- Operation stops before completi ng wash cycle p.13
- Machine is draining while being filled p.13
- In case of power failure p.13
- If too much foam is visible during spin cycle the motor will stop and drain pump will activate for 90 seconds if that elimination of foam fails up to 3 times programme ends without spinning p.13
- General information and tips p.13
- Excessive foam floats drum and or detergent drawer p.13
- Duration will be adjusted affect functionality time p.13
- When power supply is restored operation will be resumed if a power failure cuts an operating wash programme door opening is mechanically blocked to get out any laundry water level should not be seen in the glassy porthole of the door danger of burns water level has to be lowered as described in pump filter not till then pull level a beneath service flap until door as unlocked by a gentle click afterwards refix all parts p.13
- Drainage failure p.13
- Washing machine will not fill with water p.13
- Automatic adjust ment washing programme this is normal and doesn t of washing p.13
- Washing machine fails to operate p.13
- Troubleshooting without display code p.13
- Troubleshooting troubleshooting p.13
- Technical data p.14
- Basic technical information regarding the appliance p.14
Похожие устройства
-
Haier HWD80-BP14979SРуководство по эксплуатации -
Haier HWD80-BP14959AРуководство по эксплуатации -
Haier HWD80-BP14979SРуководство по эксплуатации -
Haier HWD80-BP14979Руководство по эксплуатации
-
Haier HWD80-BP14959AРуководство по эксплуатации -
Haier HWD80-BP14959AРуководство по эксплуатации -
Haier HWD80-BP14979SРуководство по эксплуатации -
Haier HWD80-BP14979Руководство по эксплуатации
-
Haier HWD80-BP14959AИнструкция по эксплуатации -
Haier HWD100-BD1499U1Инструкция по эксплуатации -
Haier HWD80-B14686Инструкция по эксплуатации -
Vestfrost VFWD 1460 SЭксплуатационная инструкция
Узнайте, как устранить распространенные проблемы со стиральной машиной, включая сбои в работе, проблемы с наполнением и сливом воды, а также советы по правильной эксплуатации.