Home
Главная
Citizen
Чековый Принтер
CT-S281L
Руководство по эксплуатации Страница: 2

Citizen CT-S281L [2/38] Declaration of conformity

CITIZEN is a registered trade mark of Citizen Holdings Co., Japan

CITIZEN es una marca registrada de Citizen Holdings Co., Japón

Company names and product names in this manual are trademarks or

registered trademarks of relevant companies.

This printer conforms to the following Standards:

The Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS

Directive 2002/95/EC, and the WEEE Directive 2002/96/EC.

LVD:EN60950-1

EMC : EN55022 Class B

EN61000-3-2

EN61000-3-3

EN55024

This declaration applies only to the 230-V model.

Declaration of Conformity

Содержание

Line thermal printer 1
Model ct s281 1
User s manual 1
Declaration of conformity 2
General precautions 4
Caution 5
Safety precautions 5
Safety precautions which should be strictly observed 5
Warning 5
Which should be strictly observed 5
Precautions on printer installation 6
Warning 6
Caution 7
Precautions in handling the printer 8
Warning 8
Caution 9
Caution 10
Daily maintenance 10
Explanation of printer parts 2 11
General outline 11
Maintenance and troubleshooting 3 11
Other 8 11
Preparation 5 11
The table of contents 11
Features 12
General outline 12
Ct s 281 rs u wh px m1 13
Model classification 13
Printer 1 ac adapter 1 ac power cord 1 sample paper roll 1 roll usb cable clamp usb interface model 1 operation panel for wall mounting 1 quick start guide 1 cd rom 1 13
The printer models are classified by the following designation method 13
Unpacking 13
When unpacking the printer confirm that the following are provided 13
Basic specifications 14
Explanation of printer parts 15
Printer appearance 15
Other built in functions 17
Paper cover inside 17
Caution 18
Connecting the ac adapter and ac power cord 18
Preparation 18
Caution 19
Connecting interface cables 19
For serial interface use cable with the following configuration 19
Pin 25 pin cable 19
Turn off the printer and unplug the power connector then follow the procedure for interface cable connection orient the interface cable terminal correctly and insert it into the interface connector 19
When disconnecting the cable always hold the connector lay the cable not to be caught by the leg or the like 19
Caution 20
Installing the printer 20
The printer can be installed horizontally or mounted vertically on the wall at the time of shipment the printer is set for horizontal installation to install the printer on the wall put the accessory operation panel on to the original one this will allow easy operation panel reading when printer is wall mounted 20
Bps and 38400 bps can also be selected by a command or the memory switch 9600bps is factory setting 21
Dip switch is provided only for serial interface specification the dip switch is located at the bottom of the paper holder to set the dip switch open the printer cover and remove the paper 21
Only serial interface type 21
Selecting baud rate 21
Setting dip switch 21
Setting dip switch only serial interface type 21
Adjusting the paper near end sensor 22
Caution 22
Move the paper near end sensor lever to forward or backward the position to be set varies in accordance with the paper roll as shown in the following table 22
Unit mm 22
Adjusting paper sensor 23
Selecting paper type 23
Caution 25
Full cutting label paper 25
When full cutting the label paper with the printer installed horizontally be sure that the guide plate is mounted on the paper exit of the printer cover this guide plate was set to the printer at the time of factory shipment the guide plate prevents cut paper from dropping in the printer 25
Caution 26
Maintenance and troubleshooting 26
Setting replacing paper rolls 26
Warning 26
Caution 27
Cleaning the print head 27
Removing jammed paper 27
Caution 28
Cutter lock error may occur with the auto cutter due to dropping of foreign object paper jam etc if the cutter blade remains protruded with cutter lock error the printer cover does not open the auto cutter can also be restored to the initial position by turning the printer on again or by pressing the feed button when the memory sw3 1 is set to off if the cutter lock error cannot be recovered by the above method release cutter lock in the following procedure 28
When the printer cover cannot be opened 28
Caution 29
Hexadecimal dump printing 29
Self printing 29
Error indication 30
External views and dimensions 31
The led status of each error including the above is shown below 31
Manual setting of memory switch 32
Memory switches can be set manually or by a command for manual setting refer to the next page the function of each memory switch is shown in the following table the white on black characters are factory setting 32
A thermal paper 35
Caution 35
Initializing the memory switch when you want to return the memory switch setting to the initial state go to write factory setting in the above procedure here open the paper cover and press and hold the feed button till buzzer sounds this allows the printer to return to the initial state all the memory switches settings are returned to the factory set values 35
Printing paper 35
Saving the setting and exiting the memory switch setting mode press the feed button shortly to move to write factory setting then press and hold the feed button the printer prints the content of new setting and exits the memory switch setting mode to return to the normal standby state unless saving the setting is executed the changed setting cannot be enabled 35
Use the paper with the start of winding to roll core is as shown below no fold line is present and paper is along the inner diameter no turnup is present no pasting to core is present outer winding print side out is used 35
Use the print paper shown in the following table or the paper with equivalent quality 35
B label paper 36
Caution 36
Do not use full sheet label paper use label paper with peel force of 200 mn 50mm between label and liner using label paper with weak peel force may result in paper jam in some case adhesive may be present between label papers or at the edge of label fixing adhesive on the paper path such as print head etc may result in paper jam at the occurrence of paper jam check for fixed adhesive remove the fixed adhesive using close moistened with ethanol when label length is less than 30 mm and the cutter is set to be disabled feeding the unlabelled area to the manual cut position and then to the first print position by using the gs ff command may cause label paper to feed one or two sheets without printing observe the life and storage condition of label paper when using label paper 36
Full cut position paper feeding direction 36
Paper type product name 36
Printable area 36
Recommended thermal label paper hd75 from nippon paper 150hbw from ricoh 36
Unit mm 36
When using label paper with ct s281xl ol refer to the following use the following paper or the equivalent paper 36
Black mark printed on the reverse 37
C black mark paper bm paper 37
Caution 37
Cut position 37
Paper feeding direction 37
Pcs value of black mark must be 0 or more 2 when using the black mark paper consider the margin of 2 mm for the print position against the standard position and 5 mm for print length 3 refer to the above drawing for the printable area and have enough margings specified in the marks e and g if the print data size is out of the printable area the printer should skip to next page 4 when using preprinted paper consider the layout of the paper 37
Printable area 37
Unit mm 37

Citizen CT-S281L [2/38] Declaration of conformity

Содержание

Похожие устройства