![BLACK & DECKER BES710-QS [17/36] After use](/img/pdf.png)
BLACK & DECKER BES710-QS [17/36] After use
![BLACK & DECKER BES710-QS [17/36] After use](/views2/1641016/page17/bg11.png)
17
ENGLISH
Alternative method for cutting crown molding
Place the molding at an angle between the fence (12) and the
saw table (11), with the top side of the molding on the table
and the bottom side of the molding on the fence as shown in
fi gure S2.
The advantage to cutting crown molding using this method
is that no bevel cut is required. Minute changes in the miter
angle can be made without affecting the bevel angle. This
way,when corners other than 90º are encountered, the saw
can be quickly and easily adjustedfor them.
Instructions for cutting crown molding angled
between the fence and base of the saw for all cuts
This saw can cut up to 14 mm x 92 mm crown molding nested.
Angle the molding so the bottom of the molding (part
which goes against the wall when installed) is against the
fence (12) and the top of the molding is resting on the saw
table (11), as shown in fi gure S2.
The angled “fl ats” on the back of the molding must rest
squarely on the fence and saw table.
Inside Corner Outside Corner
Left Side Miter right at 45°
Save right side of cut
Miter left at 45°
Save right side of cut
Right Side Miter left at 45°
Save left side of cut
Miter right at 45°
Save left side of cut
Special Cuts
Never make any cut unless the material is secured on the
table and against the fence.
Bowed material (fi g. T1, T2)
When cutting bowed material always position it as shown in
fi gure T1 and never like that shown in fi gure T2. Positioning
the material incorrectly will cause it to pinch the blade near the
completion of the cut.
Cutting round material
Rounded material should be clamped or held fi rmly to the
fence to keep It from rolling. This is extremely important when
making angle cuts.
Cutting large material (fi g. U)
Occasionally you will encounter a piece of wood a little too
large to fi t beneath the lower guard.
To clear the guard over the wood, with the saw off and your
right hand on the operating handle, place your right thumb
outside of the upper portion of the guard and roll the guard up
just enough to clear the wood, as shown in fi gure U. Release
the guard prior to starting the motor. The guard mechanism
will function properly during the cut. Only do this when
necessary.
NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD
OPEN WHEN OPERATING THIS SAW.
Warning! Always be sure that the tool is switched off and
unplugged before adjusting or checking the tools function.
After use
After use, wipe off chips and dust adhering to the tool with
a cloth or the like.
Keep the blade guard clean according to the directions in
the previously covered section.
Lubricate the sliding portions with machine oil to prevent
rust.
When storing the tool, pull the carriage toward you fully.
Carrying the tool
Make sure the tool is unplugged.
Secure the blade at the 0° bevel angle and turn the base
to the right mitre angle fully with the slide bar locking scre
(28).
Secure the slide bars after pulling the carriage toward you
fully.
Lower the handle fully and lock it in the position by
pushing in the saw head locking pin (17).
Carry the tool by holding the carry handle (22).
If you remove the clamp, dust bag, etc., you can carry the
tool more easily.
Carry the tool by one hand holding the carrying handle
(22) and one hand holding the tool base.
Caution! Always secure all moving portions before carrying
the tool.
Saw head locking pin (17) is for carrying and storage
purposes only and not for any cutting operations.
Troubleshooting
Problem Possible Cause Solution
Motor does
not start
Saw not plugged in. Check that all cords are plugged in.
Angle of cut
inaccurate
Mitre table
unlocked.
Use mitre table locking lever (see
Adjusting the mitre angle section.
Too much sawdust
under table.
Vacuum or blow out dust. Wear eye
protection.
Cutting arm
cannot fully
raise, or blade
guard cannot
fully close
Parts Failure. Contact service centre.
Pivot spring not
replaced properly
after service.
Contact service centre.
Sawdust build up. Clean and lubricate moving parts.
Saw head locking
pin not set properly.
Check, adjust, and properly set saw
head locking pin.
Blade binds,
jams or
shakes
Saw blade
damaged.
Replace blade.
Dull blade. Replace or sharpen blade.
Improper blade. Replace blade.
Warped blade. Replace blade.
Содержание
- English 8
- General power tool safety warnings 8
- Intended use 8
- Safety instructions 8
- English 9
- Safety instructions for mitre saws 9
- Additional safety instructions for mitre saws 10
- English 10
- Before each cut ensure that the machine is stable 11
- Before use and after any maintenance the blade guard must be checked to ensure proper function this test must be performed with the saw switched off and unplugged the arm must be raised and lowered to ensure the guard covers the blade and the blade does not contact the guard if the guard fails to operate correctly have your power tool serviced by a qualifi ed repair agent call black decker customer services for you nearest service agent 11
- Before using or fi tting any accessory consult the instruction manual the improper use of an accessory can cause damage 11
- Check periodically that the motor air slots are clean and free of chips 11
- Consider using specially designed noise reduction blades 11
- Cutting accessory contacting a live wire may make cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock 11
- Do not allow untrained people to operate this machine 11
- Do not operate the machine without the guard in position do not operate the machine if the guard does not function or is not maintained properly 11
- Do not take hold of the saw blade after working before it has cooled the saw blade becomes very hot while working 11
- Do not use blades of larger or smaller diameter than recommended for the proper blade rating refer to the technical data use only the blades specifi ed in this manual complying with en 847 1 11
- Do not use cracked bent damaged deformed saw blades 11
- Do not use high speed steel hss saw blades 11
- Do not wedge anything against the fan to hold the motor shaft 11
- Do not work with material containing asbestos asbestos is considered to be carcinogenic 11
- English 11
- Ensure that any spacers and spindle rings used are suitable for the purpose as stated by black decker 11
- Ensure that the arm is securely fi xed when performing bevel cuts 11
- Ensure that the blade is mounted correctly before use make sure that the blade rotates in the correct direction keep the blade sharp follow instruction for lubricating and changing accessories 11
- Ensure the machine and the work area are provided with adequate general or localised lighting 11
- Ensure the speed marked on the saw blade is at least equal to the speed marked on the saw 11
- Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord 11
- Keep handles dry clean and free from oil and grease 11
- Keep the surrounding area of the machine well maintained and free of loose materials e g chips and off cuts 11
- Make sure all locking knobs and handles are tight before starting any operation 11
- Never attempt to stop the machine in motion rapidly by jamming a tool or other means against the blade serious accidents can be caused unintentionally in this way 11
- Never make the warning signs on the power tool unrecognisable 11
- Never perform any cleaning maintenance removal of any off cuts or other parts of the work piece form the cutting area when the machine is running and the saw head is not in the rest position 11
- Never stand on the power tool serious injuries could occur when the power tool tips over or when coming in contact with the saw blade 11
- Never use your saw without the table insert 11
- Of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury and or damage to property 11
- Raise the blade from the table insert in the work piece prior to releasing the on of switch 11
- Repairs to the cut line guidance system should be carried out by authorised repair agents or black decker service staff 11
- Replace the kerf plate when worn 11
- Select the correct blade for the material to be cut 11
- The blade guard on your saw will automatically raise when the arm is brought down it will lower over the blade when the arm is raised the guard can be raised by hand when installing or removing saw blades or for inspection of the saw never raise the blade guard manually unless the machine is switched off 11
- This mitre saw has been designed for sawing wood plastic and nonferrous metal only do not use the saw 11
- To avoid injury from materials being thrown unplug the saw to avoid accidental starting and then remove small materials 11
- Unplug the machine before carrying out any maintenance or when changing the blade 11
- Use the dust bag provided when sawing wood 11
- Warning contact with or inhalation of dusts arising from sawing applications may endanger the health of the operator and possible bystanders wear a dust mask specifi cally designed for protection against dust and fumes and ensure that persons within or entering the work area are also protected 11
- Wear eye protection to reduce the risk of personal injury 11
- Wear gloves when handling saw blades and rough material saw blades should be carried in a holder when practicable 11
- Wear hearing protection to reduce the risk of induced hearing loss 11
- When possible always mount the machine to a bench 11
- English 12
- Features 12
- Labels on tool 12
- Residual risks 12
- Using an extension cable 12
- Voltage drops 12
- Assembly 13
- Bench mounting fig 13
- Dust collection fig 13
- English 13
- Support stand bes710 only fig e 13
- Table extension rail fig c d 13
- To install workpiece clamp fig h 13
- Adjusting the bevel angle fig m 14
- Adjusting the mitre angle fig l 14
- Changing or installing a new saw blade fig i j k 14
- Cutting depth 14
- English 14
- Fence adjustment 14
- Installing a blade 14
- Removing the blade 14
- Switch action fig 14
- Bevel square to table adjustment fig p 15
- Body and hand position fig o1 o4 15
- Crosscuts 15
- Cutting picture frames shadow boxes and other four sided projects fig q1 q2 15
- Cutting trim molding and other frames fig q2 15
- English 15
- Use of cut line system fig 15
- Cutting base molding fig r 16
- Cutting base molding up to 70 mm 90 mm high vertically against the fence 16
- Cutting compound miters fi g q3 16
- Cutting crown molding 16
- English 16
- Instructions for cutting crown molding laying fl at and using the compound features 16
- After use 17
- Alternative method for cutting crown molding 17
- Bowed material fi g t1 t2 17
- Carrying the tool 17
- Cutting large material fi g u 17
- Cutting round material 17
- English 17
- Instructions for cutting crown molding angled between the fence and base of the saw for all cuts 17
- Special cuts 17
- Troubleshooting 17
- Ec declaration of conformity 18
- English 18
- Guarantee 18
- Protecting the environment 18
- Technical data 18
- These products also comply with directive 2006 42 ec 2014 30 eu and 2011 65 eu 18
- Назначение 19
- Общие правила безопасности при работе с электроинструментом 19
- Правила техники безопасности 19
- Инструкции по технике безопасности для торцовочных пил 20
- Дополнительные инструкции по технике безопасности для торцовочных пил 22
- Остаточные риски 23
- Уровень шума 23
- Использование удлинительного кабеля 24
- Перепады напряжения 24
- Составные части 24
- Условные обозначения на инструменте 24
- Выдвижная опора рис с и d 25
- Монтаж на верстаке рис 25
- Опорная лапа только bes710 рис е 25
- Пылеудаление рис 25
- Сборка 25
- Установка зажима для заготовки рис н 25
- Глубина пропила 26
- Замена или установка нового пильного диска рис i j k 26
- Регулировка направляющей 26
- Регулировка угла наклона рис м 26
- Регулировка угла скоса рис l 26
- Снятие диска 26
- Установка диска 26
- Включение рис 27
- Использование системы подсветки линии реза рис 27
- Поперечный распил 27
- Изготовление картинных рам ящиков для рассады и прочих четырёхсторонних конструкций рис q1 q2 28
- Комбинированное пиление рис q3 28
- Пиление багетов и изготовление рам рис q2 28
- Пиление профилей плинтусов рис r 28
- Положение тела и рук рис o1 o4 28
- Регулировка перпендикулярности диска относительно стола рис р 28
- Инструкции по пилению потолочных плинтусов уложенных горизонтально с применением метода комбинированного пиления 29
- Пиление потолочных плинтусов 29
- Распил профилей плинтусов шириной до 70 мм 90 мм вертикально расположенных вплотную к направляющей 29
- Альтернативный способ пиления потолочных плинтусов 30
- Заготовки изогнутой формы рис т1 т2 30
- Инструкции по пилению потолочных плинтусов расположенных под углом между направляющей и основанием пилы с применением всех видов резов 30
- Переноска инструмента 30
- После использования 30
- Распил круглых профилей 30
- Распиловка длинных заготовок рис u 30
- Специальные резы 30
- Защита окружающей среды 31
- Неисправности и способы их устранения 31
- Переносите инструмент одной рукой держась за ручку для переноски 22 другой рукой поддерживая основание инструмента внимание перед переноской инструмента всегда фиксируйте все подвижные части стопорный штифт пильной головки 17 предназначен только для переноски и хранения инструмента но не для выполнения каких либо операций по резанию 31
- Пожалуйста утилизируйте электрические изделия и аккумуляторные батареи в соответствии с местными нормами дополнительная информация доступна по адресу www helpu com 31
- Раздельный сбор изделия и аккумуляторные батареи с данным символом на маркировке запрещается утилизировать с обычными бытовыми отходами изделия и аккумуляторные батареи содержат материалы которые могут быть извлечены или переработаны снижая потребность в исходном сырье 31
- Технические характеристики 31
- Гарантия 32
- Заявление о соответствии нормам ес 32
- Эти изделия также соответствуют директивам 2006 42 ec 2014 30 eu и 2011 65 eu 32
- Www helpu com 35
Похожие устройства
- Kress KU334 Инструкция по эксплуатации
- Patriot Мотоблок УРАЛ +Дрель-шуруповерт BR 114Li THE ONE Инструкция по эксплуатации
- Einhell PXC TC-CD 18/35 Li-Solo без АКБ и ЗУ Инструкция по эксплуатации
- Einhell PXC TC-AG 18/115 Li-Solo без акк. и з.у Инструкция по эксплуатации
- Rapid EG Point (5000432) Инструкция по эксплуатации
- Worx WX500.9 без акк. и з.у Инструкция по эксплуатации
- Makita DGD801Z без акк. и з.у Инструкция по эксплуатации
- Worx AiDrill WX178.1 Инструкция по эксплуатации
- Dewalt DCD706D2-QW Инструкция по эксплуатации
- Bosch GBH 180-LI Brushless (0.611.911.120) без акк. и з.у Инструкция по эксплуатации
- Интерскол ДАУ-13/18В (574.2.2.70) Инструкция по эксплуатации
- Bosch GO kit (06019H20K1) Инструкция по эксплуатации
- Вихрь ПТ-255ПЛ Инструкция по эксплуатации
- Greenworks GD24SDS2 без акк. и з.у Инструкция по эксплуатации
- Kress KU721 Инструкция по эксплуатации
- Ставр АКБ-20/2 Инструкция по эксплуатации
- DWT ABS-18 L-2 BMC Инструкция по эксплуатации
- DWT SBH08-26 BMC Инструкция по эксплуатации
- DWT WS08-125 TV Инструкция по эксплуатации
- BLACK & DECKER BCG720N-XJ без акк. и з.у Инструкция по эксплуатации