![Kress KU334 — инструкции по эксплуатации и советы по использованию инструмента [8/16]](/icons/site-icon-64.png){kind=icon}
Kress KU334 — инструкции по эксплуатации и советы по использованию инструмента [8/16]
Превью страниц
Страница 8 /
16
![Kress KU334 [8/16] Accessories](/views2/1889196/page8/bg8.png)
8
EN
ACCESSORIES
Auxiliary handle 1
Depth gauge 1
We recommend that you purchase your accessories
from the same store that sold you the tool. Choose the
type according to the work you intend to undertake.
Refer to the accessory packaging for further details.
Store personnel can assist you and offer advice.
OPERATING
INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for hammer drilling in
concrete, brick and stone as well as for light chiseling
work.
WARNING! Before any work on the
machine itself, pull the mains plug.
OPERATION
Action Figure
Selecting The Operating Mode See Fig. A
Inserting Drill Bits See Fig. B1
Removing Drill Bits See Fig. B2
Adjusting the Auxiliary Handle See Fig. C
Using the Depth Gauge See Fig. D
On/Off Switch See Fig. E
Lubrication Machine
Caution: Keep the container
of grease away from children.
See Fig. F
Replacing the Brushes
● Unscrew the carbon brush cap
with screwdriver.
● When brushes need replacement
always renew both brushes.
● Completely screw down the
carbon brush cap. Check that the
tool is working. Before use, allow
it run for a few minutes to enable
the brushes to settle.
See Fig. G1,
G2
CONSTANT ELECTRONIC
CONTROL
/
OVERLOAD PROTECTION /
WORKING HINTS FOR
YOUR TOOL
1. Reduce the pressure on the drill bit when it is about
to break through. This will prevent the drill from
jamming.
2. When drilling a large hole, rst drill a pilot hole using
a smaller drill bit.
3. Always apply pressure to your drill bit in a straight
line, and if possible at right angles to the workpiece.
4. Never change the operating mode whilst the drill is
running.
5. Do not apply excessive pressure to the tool when
chiseling. Expressive force does not speed up the
work.
Содержание
58- A wrench or a key left attached to a rotating part of the power tool may result in personal injury
- Any power tool that cannot be controlled with the switch is dangerous and must be repaired
- A moment of inattention while operating power tools may result in serious personal injury
- Use of an rcd reduces the risk of electric shock
- General power tool safety warnings
- Use of a cord suitable for outdoor use reduces the risk of electric shock
- Distractions can cause you to lose control
- Unmodified plugs and matching outlets will reduce risk of electric shock
- Damaged or entangled cords increase the risk of electric shock
- Cluttered
- This enables better control of the power tool in unexpected situations
- Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents
- There is an increased risk of electric shock if your body is earthed or grounded
- The correct power tool will do the job better and safer at the rate for which it was designed
- And instructions may result in electric shock fire and or serious injury
- Such preventive safety measures reduce the risk of starting the power tool accidentally
- Save all warnings and instructions for future reference the term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool
- Protective equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries
- Properly
- Power tools create sparks which may ignite the dust or fumes
- Ower tools are dangerous in the hands of untrained users
- Or dark areas invite accidents
- Water entering a power tool will increase the risk of electric shock
- Many accidents are caused by poorly maintained power tools
- Warning read all safety warnings and all instructions failure to follow the warnings
- Maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control
- Use of dust collection can reduce dust related hazards
- Loose clothes jewellery or long hair can be caught in moving parts
- Technical data
- Symbol
- Hammer safety warnings
- Component list
- Additional safety rules for hammer
- Working hints for your tool
- Operating instructions
- Accessories
- Trouble shooting
- Maintenance
- Environmental protection
- Общие правила техники безопасности при работе с электроинструментом
- И инструкциями по технике безопасности невыполнение предостережений и инструкций может привести к поражению электрическим током пожару и или серьезным травмам
- Предостережение внимательно ознакомьтесь с предостережениями
- Условные обозначения
- Правила техники безопасности при работе с отбойным молотком
- Носитепылезащитнуюмаску
- Носитезащитуоргановслуха
- Носитезащитуоргановзрения
- Дополнительные правила техники безопасности при работе с отбойным молотком
- Длясокращениярискатравмы пользовательдолженпрочитать руководствопоэксплуатации инструмента
- Двойнаяизоляция
- Перечень компонентов
- Аксессуары
- Технические данные
- Инструкции по эксплуатации
- Советы по работе с инструментом
- Техническое обслуживание
- Выявление и устранение неисправностей
- Охрана окружающей среды
Похожие устройства
-
Kress KU332Инструкция по эксплуатации -
Kress KU320Инструкция по эксплуатации -
Finepower CRHBL23Инструкция по работе -
Finepower OneBase CRHBL23Руководство пользователя -
Wesco WS3212KРуководство пользователя -
Wesco WS3228KИнструкция по работе -
Sturm RH 2509BZИнструкция по работе -
Sturm RH2532VИнструкция пользователя -
KLPRO KLPM18BРуководство по настройке -
Worx WX394.XРуководство по эксплуатации -
Worx WX394Руководство по работе с устройством
-
KLPRO KLPM2801Руководство по настройке
Узнайте, как правильно использовать инструмент для бурения и долбления. Следуйте инструкциям по замене насадок и уходу за инструментом для безопасной работы.