![Kress KU334 — troubleshooting and Maintenance Guide for Power Tools [9/16]](/icons/site-icon-64.png){kind=icon}
Kress KU334 — troubleshooting and Maintenance Guide for Power Tools [9/16]
Превью страниц
Страница 9 /
16
![Kress KU334 [9/16] Maintenance](/views2/1889196/page9/bg9.png)
9
EN
TROUBLE SHOOTING
The following table gives checks and actions that you can perform if your machine does not operate correctly.
If these do not identify/solve the problem, contact Kress Customer Service.
I would add a comment here to again recommend that you apply grease to the shank of every drill bit used.
Symptom Possible Cause Possible Solution
Machine fails to operate
No power supply to machine
Turn power on
Use another socket
The brushes are worn out
Have a qualied person to check them,
and replace them if necessary
The power and hammer efciency
of the machine is low.
Machine may be cold
Warm up the machine for 1-2 minutes
until it reaches a proper working
temperature
Your drill bit does not slide
freely in the chuck
Clean the dust and debris inside the
chuck; Grease the shank of the bit if
necessary.
There is no enough grease oil
in the gearbox
Have a qualied person to add some
grease oil (about 2 or 3 bottle caps)
Your drill bit will not t into the
chuck easily
The chuck is dirty with dust
and debris.
Clean the dust and debris from inside
the chuck
The shank of the bit is
damaged or distorted
Change a new bit
MAINTENANCE
Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.
There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power
tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean.
Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal
and will not damage your power tool.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard.
Add approximately 10 grams of 1# lubricant (about 2-3 water bottle caps) to the gearbox every 100 operating hours.
ENVIRONMENTAL PROTECTION
Disposal
The machine, its accessories and packaging materials should be sorted for environmentally friendly
recycling.
The plastic components are labeled for categorized recycling
Содержание
58- A wrench or a key left attached to a rotating part of the power tool may result in personal injury
- Any power tool that cannot be controlled with the switch is dangerous and must be repaired
- A moment of inattention while operating power tools may result in serious personal injury
- Use of an rcd reduces the risk of electric shock
- General power tool safety warnings
- Use of a cord suitable for outdoor use reduces the risk of electric shock
- Distractions can cause you to lose control
- Unmodified plugs and matching outlets will reduce risk of electric shock
- Damaged or entangled cords increase the risk of electric shock
- Cluttered
- This enables better control of the power tool in unexpected situations
- Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents
- There is an increased risk of electric shock if your body is earthed or grounded
- The correct power tool will do the job better and safer at the rate for which it was designed
- And instructions may result in electric shock fire and or serious injury
- Such preventive safety measures reduce the risk of starting the power tool accidentally
- Save all warnings and instructions for future reference the term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool
- Protective equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries
- Properly
- Power tools create sparks which may ignite the dust or fumes
- Ower tools are dangerous in the hands of untrained users
- Or dark areas invite accidents
- Water entering a power tool will increase the risk of electric shock
- Many accidents are caused by poorly maintained power tools
- Warning read all safety warnings and all instructions failure to follow the warnings
- Maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control
- Use of dust collection can reduce dust related hazards
- Loose clothes jewellery or long hair can be caught in moving parts
- Technical data
- Symbol
- Hammer safety warnings
- Component list
- Additional safety rules for hammer
- Working hints for your tool
- Operating instructions
- Accessories
- Trouble shooting
- Maintenance
- Environmental protection
- Общие правила техники безопасности при работе с электроинструментом
- И инструкциями по технике безопасности невыполнение предостережений и инструкций может привести к поражению электрическим током пожару и или серьезным травмам
- Предостережение внимательно ознакомьтесь с предостережениями
- Условные обозначения
- Правила техники безопасности при работе с отбойным молотком
- Носитепылезащитнуюмаску
- Носитезащитуоргановслуха
- Носитезащитуоргановзрения
- Дополнительные правила техники безопасности при работе с отбойным молотком
- Длясокращениярискатравмы пользовательдолженпрочитать руководствопоэксплуатации инструмента
- Двойнаяизоляция
- Перечень компонентов
- Аксессуары
- Технические данные
- Инструкции по эксплуатации
- Советы по работе с инструментом
- Техническое обслуживание
- Выявление и устранение неисправностей
- Охрана окружающей среды
Похожие устройства
-
Kress KU332Инструкция по эксплуатации -
Kress KU320Инструкция по эксплуатации -
Finepower CRHBL23Инструкция по работе -
Finepower OneBase CRHBL23Руководство пользователя -
Wesco WS3212KРуководство пользователя -
Wesco WS3228KИнструкция по работе -
Sturm RH 2509BZИнструкция по работе -
Sturm RH2532VИнструкция пользователя -
KLPRO KLPM18BРуководство по настройке -
Worx WX394.XРуководство по эксплуатации -
Worx WX394Руководство по работе с устройством
-
KLPRO KLPM2801Руководство по настройке
Discover essential troubleshooting tips and maintenance practices for your power tools. Ensure optimal performance and longevity with these helpful guidelines.