Home
Главная
Skil
Шлифовальная Машина
7420 LA
Инструкция по эксплуатации Страница: 5

Skil 7420 LA Инструкция по эксплуатации онлайн [5/96] 92527

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

dierent from those intended could result in a hazardous

situation.

5) SERVICE

a) Haveyourpowertoolservicedbyaqualiedrepair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

SAFETY INSTRUCTIONS FOR SANDERS

GENERAL

• This tool should not be used by people under the age

of 16 years

• This tool is not suitable for wet sanding

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Do not work materials containing asbestos

(asbestos is considered carcinogenic)

• Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Do not continue to use worn, torn or heavily clogged

sanding sheets

BEFORE USE

• Always check that the supply voltage is the same as

the voltage indicated on the nameplate of the tool (tools

with a rating of 230V or 240V can also be connected to

a 220V supply)

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• The noise level when working can exceed 85 dB(A);

wear ear protection

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Wear protective gloves, safety glasses, close-tting

clothes and hair protection (for long hair)

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• When sanding metal, sparks are generated; do not

use dustbag and keep other persons and combustible

material from work area

DURING USE

• Always keep the cord away from moving parts of the

tool; direct the cord to the rear, away from the tool

• Do not touch the moving sanding disc

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

AFTER USE

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of

this tool, it must be disposed of safely and not left

unattended

USE

• Backing pads

- never run the tool without backing pad A

! replace damaged backing pads immediately

(loosen/fasten 4 pad screws B)

! unplug tool before removing/mounting backing

pads

• Mounting of sanding sheet ④

- mount VELCRO sanding sheet as illustrated

- if necessary, clean backing pad rst

! perforation in sanding sheet should correspond

with perforation in sanding foot

! the dust suction requires the use of perforated

sanding sheets

! replace worn sanding sheets in time

• Dust suction ⑤

For optimal dust pick-up performance

- mount dustbag D

- empty dustbag regularly

! do not use dustbag when sanding metal

• On/o

- before switching on the tool, you should place it with

the entire sanding surface on the workpiece

- when switching on, do not apply too much pressure

on the tool

- switch on/o the tool by pushing switch E in "I"/"O"

position

! be aware of the sudden impact when the tool is

switched on

! beforeswitchingothetool,youshouldliftit

from the workpiece

• Holding and guiding the tool ⑥

! whileworking,alwaysholdthetoolatthegrey-

coloured grip area(s)

! do not apply too much pressure on the tool; let

the sanding surface do the work for you

- guide the tool parallel to the working surface and move

it in circles or in a cross pattern

- do not tilt the tool in order to avoid deep unwanted

sanding marks

- keep ventilation slots F uncovered

Skil 7420 LA Инструкция по эксплуатации онлайн [5/96] 92527

Содержание

Похожие устройства