Skil 9345 LG Инструкция по эксплуатации онлайн [8/176] 92605

Skil 9345 LG Инструкция по эксплуатации онлайн [8/176] 92605
8
forces.Alwaysuseauxiliaryhandle,ifprovided,for
maximumcontroloverkickbackortorquereaction
duringstart-up.The operator can control torque reactions
or kickback forces, if proper precautions are taken.
b) Neverplaceyourhandneartherotatingaccessory.
The accessory may kickback over your hand.
c) Donotpositionyourbodyintheareawherepower
toolwillmoveifkickbackoccurs.Kickback will propel
the tool in the direction opposite to the wheel’s movement
at the point of snagging.
d) Usespecialcarewhenworkingcorners,sharp
edgesetc.Avoidbouncingandsnaggingthe
accessory.Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause loss
of control or kickback.
e) Donotattachasawchainwoodcarvingbladeor
toothedsawblade.Such blades create frequent
kickback and loss of control.
3)SAFETYWARNINGSSPECIFICFORGRINDINGAND
ABRASIVECUTTING-OFFOPERATIONS
a) Useonlywheeltypesthatarerecommendedforyour
powertoolandthespecificguarddesignedforthe
selectedwheel.Wheels for which the power tool was not
designed cannot be adequately guarded and are unsafe.
b) Thegrindingsurfaceofthecentredepressedwheels
mustbemountedbelowtheplaneoftheguardlip. An
improperly mounted wheel that projects through the plane
of the guard lip cannot be adequately protected.
c) Theguardmustbesecurelyattachedtothepower
toolandpositionedformaximumsafety,sotheleast
amountofwheelisexposedtowardstheoperator.
The guard helps to protect the operator from broken
wheel fragments, accidental contact with wheel and
sparks that could ignite clothing.
d) Wheelsmustbeusedonlyforrecommended
applications.For example: Do not grind with the side of
a cut-o wheel. Abrasive cut-o wheels are intended for
peripheral grinding; side forces applied to these wheels
may cause them to shatter.
e) Alwaysuseundamagedwheelflangesthatareof
correctsizeandshapeforyourselectedwheel.
Proper wheel anges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-o
wheels may be dierent from grinding wheel anges.
f)
Donotuseworndownwheelsfromlargerpowertools.
A wheel intended for a larger power tool is not suitable for
the higher speed of a smaller tool and may burst.
4)ADDITIONALSAFETYWARNINGSSPECIFICFOR
CUTTING OFF OPERATIONS
a) Donot“jam”thecut-offwheelorapplyexcessive
pressure.Donotattempttomakeanexcessive
depthofcut.Overstressing the wheel increases the
loading and susceptibility to twisting or binding of the
wheel in the cut and the possibility of kickback or wheel
breakage.
b) Donotpositionyourbodyinlinewithandbehind
therotatingwheel.When the wheel, at the point of
operation, is moving away from your body, the possible
kickback may propel the spinning wheel and the power
tool directly at you.
c) Whenthewheelisbindingorwheninterruptingacut
foranyreason,switchoffthepowertoolandholdthe
powertoolmotionlessuntilthewheelcomestoa
completestop.Neverattempttoremovethecut-off
wheelfromthecutwhilethewheelisinmotion,
otherwisekickbackmayoccur.Investigate and take
corrective action to eliminate the cause of wheel binding.
d) Donotrestartthecuttingoperationinthe
workpiece.Letthewheelreachfullspeedand
carefullyre-enterthecut.The wheel may bind, walk up
or kickback if the power tool is restarted in the workpiece.
e) Supportpanelsoranyoversizedworkpieceto
minimizetheriskofwheelpinchingandkickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
f) Useextracautionwhenmakinga“pocketcut”into
existingwallsorotherblindareas.The protruding
wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
5)SAFETYWARNINGSSPECIFICFORSANDING
OPERATIONS
a) Whensanding,donotuseexcessivelyoversized
sandingdiscpaper.Followthemanufacturers’
recommendationswhenselectingsandingpaper.
Larger sanding paper extending beyond the sanding pad
presents a laceration hazard and may cause snagging,
tearing of the disc, or kickback.
6)SAFETYWARNINGSSPECIFICFORWIRE
BRUSHING OPERATIONS
a) Beawarethatwirebristlesarethrownbythebrush
evenduringordinaryoperation.Donotoverstress
thewiresbyapplyingexcessiveloadtothebrush.
The wire bristles can easily penetrate light clothing and/
or skin.
b)
Iftheuseofaguardisrecommendedforwire
brushing,donotallowanyinterferenceofthewire
wheelorbrushwiththeguard.Wire wheel or brush may
expand in diameter due to work load and centrifugal forces.
GENERAL
This tool is not suitable for wet grinding/cutting
Only use the anges which are supplied with this tool
This tool should not be used by people under the age of
16 years
• Alwaysdisconnectplugfrompowersourcebefore
makinganyadjustmentorchanginganyaccessory
ACCESSORIES
For mounting/using non-SKIL accessories observe the
instructions of the manufacturer concerned
• Useonlygrinding/cuttingdiscswithamaximum
thicknessof8mmandaspindleholediameterof22
mm
Never use reducors or adaptors to t large-hole grinding/
cutting discs
Never use accessories with a “blind” threaded hole
smaller than M14 x 21 mm
OUTDOOR USE
Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
BEFORE USE
Before using the tool for the rst time, it is recommended
to receive practical information

Содержание

Скачать