Skil 9345 LG Инструкция по эксплуатации онлайн [9/176] 92605
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Skil 9345 LG Инструкция по эксплуатации онлайн [9/176] 92605

Skil 9345 LG Инструкция по эксплуатации онлайн [9/176] 92605
9
• Usesuitabledetectorstofindhiddenutilitylinesor
callthelocalutilitycompanyforassistance (contact
with electric lines can lead to re or electrical shock;
damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• Donotworkmaterialscontainingasbestos (asbestos
is considered carcinogenic)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wearadustmaskandworkwithadust
extractiondevicewhenconnectable
• Certain kinds of dust are classied as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wearadustmaskand
workwithadustextractiondevicewhenconnectable
• Follow the dust-related national requirements for the
materials you want to work with
• Be careful when cutting grooves, especially in supporting
walls (slots in supporting walls are subject to country-
specic regulations; these regulations are to be observed
under all circumstances)
• Securetheworkpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Do not clamp the tool in a vice
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
• Inrush currents cause short-time voltage drops; under
unfavourable power supply conditions, other equipment
may be aected (if the system impedance of the power
supply is lower than 0,104 + j0,065 Ohm, disturbances
are unlikely to occur); if you need further clarication, you
may contact your local power supply authority
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Never use the tool when cord is damaged; have it
replaced by a qualied person
• In case of electrical or mechanical malfunction,
immediately switch o the tool and disconnect the plug
• In case of current interruption or when the plug is
accidentally pulled out, unlock the on/o switch J 2
immediately in order to prevent uncontrolled restarting
AFTER USE
• After switching o the tool, never stop the rotation of the
accessory by a lateral force applied against it
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut o the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Mounting of accessories 5
! disconnecttheplug
- clean spindle A and all parts to be mounted
- push spindle-lock button D
- tighten clamping ange B with key C
! whenspindleAislocked,switchJ/Kcannotbe
activated
- press button E to unlock spindle A
- for removing accessories handle vice-versa
! grinding/cuttingdiscsbecomeveryhotduring
use;donottouchthemuntiltheyhavecooled
down
! alwaysmountbackingpadwhenusingsanding
accessories
! neveruseagrinding/cuttingdiscwithoutthelabel
(“blotter”)whichisgluedontoit(ifprovided)
• Mounting of auxiliary handle F 6
! disconnecttheplug
• Removing/mounting/adjusting of protective guard G 7
! disconnecttheplug
! ensurethattheclosedsideoftheprotective
guardalwayspointstotheoperator
- if necessary, adjust protective guard G by tightening
screw X which is pre-set at manufacturing (ensure
thattheprotectiveguardisclosed)
• Before using the tool
- ensure that accessory is correctly mounted and rmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
• On/o (two locking switch positions) 8
! beawareofthesuddenimpactwhenthetoolis
switchedon
! beforetheaccessoryreachestheworkpiece,the
toolshouldrunatfullspeed
! beforeswitchingoffthetool,youshouldliftit
fromtheworkpiece
! theaccessorycontinuestorotateforashorttime
afterthetoolhasbeenswitchedoff
• Two hand positions 9
• Grinding 0
- move the tool back and forth with moderate pressure
! neveruseacuttingdiscforsidegrinding
• Cutting !
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of the
cutting disc do the work
- the working speed of the cutting disc depends on the
material to be cut
- do not brake cutting discs with side pressure
• Holding and guiding the tool
! whileworking,alwaysholdthetoolatthe
grey-colouredgriparea(s)@
- always hold the tool rmly with both hands, so you will
have full control of the tool at all times
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust y
away from the body
- provide for a secure stance
- keep ventilation slots L 2 uncovered

Содержание

Похожие устройства

Скачать