Aten VK112EU Краткое руководство по установке Блока клавиш онлайн
Макгруп McGrp.ru
Задайте вопрос
Зарегистрироваться

Aten VK112EU Краткое руководство по установке Блока клавиш онлайн

Aten VK0200 Краткое руководство по установке столешницы с клавиатурой онлайн
VK0200TTK / VK112EUTTK Control Pad / Keypad Tabletop Kit
www.aten.com
B
Installation
© Copyright 2023 ATEN
®
International Co. Ltd.
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd.
All rights reserved. All other trademarks are the property of their respective owners.
Released: 03/2023
Control Pad / Keypad Tabletop Kit
Quick Start Guide
VK0200TTK / VK112EUTTK
A
Hardware Overview
Package Contents
1 tabletop enclosure
4 anchors
4 M4x18 screws
6 M3x8 screws
1 user instructions
Support and Documentation Notice
All information, documentation, fi rmware,
software utilities, and specifi cations
contained in this package are subject to
change without prior notifi cation by the
manufacturer.
To reduce the environmental impact of
our products, ATEN documentation and
software can be found online at
http://www.aten.com/download/
Technical Support
www.aten.com/support
Scan for more information
VK0200TTK VK112ETTK
User Manual
A
Hardware Overview
1
front knockout
2
M3x8 screw holes
3
rear knockout seal
4
wall-mount hook holes
5
M4x18 screw holes
6
bottom knockout
B
Installation
Note:
For your safety, always turn off the power before working on
an enclosure.
Desktop Mount
1
Place the enclosure on a desk where a hole is punched out to
provide a path for wires. Optionally secure the enclosure to the
desk with the four M4x18 screws provided.
2
Depending on your application, run the cables through the rear or
bottom knockout to the front knockout.
Note:
The rear knockout can be fully covered. Loosen the 2 screws
and rotate the knockout seal to make the notch upward to fully
cover the hole. Secure it again with the 2 screws.
3
Connect the required cables to the control pad / keypad.
Note:
Please refer to the Wiring Information section of ATEN
Control System User Manual for how to join the wires.
4
Fold the wires into the enclosure and then secure the control pad /
keypad with the six M3x8 screws provided.
5
Install the buttons and faceplate to the control pad / keypad.
Wall Mount
1
(Optional) To secure the enclosure to the wall, drill the pilot holes
through the wall and put the 4 anchors in the wall in advance.
2
With the rear side downwards, align the wall-mount holes to the
pre-installed wall studs, and then attach the enclosure to the wall
by mounting it to the wall studs. Optionally secure it with the four
M4x18 screws provided.
3
Depending on your application, run the cable from the rear or
bottom knockout to the front knockout.
Note:
The rear knockout can be fully covered. Loosen the 2 screws
and rotate the knockout seal to make the notch upward to fully
cover the hole. Secure it again with the 2 screws.
4
Connect the cables to the control pad / keypad.
Note:
Please refer to the Wiring Information section of ATEN
Control System User Manual for how to join the wires.
5
Fold the wires into the enclosure and then secure the control pad /
keypad with the six M3x8 screws provided.
6
Install the buttons and faceplate to the control pad / keypad.
1
22
3
4
5
6
5
1
2
3
4
5
1
1
2
3
4
5
6
Desktop Mount
Wall Mount

Содержание

Похожие устройства

Скачать