Festool Rustofix RAS 180.03 E-HR 570775 Инструкция по эксплуатации онлайн [13/86] 9201
13
arbour holes that do not match the mounting
hardware of the power tool will run out of bal-
ance, vibrate excessively and may cause loss
of control.
- Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or acces-
sory is dropped, inspect for damage or install
an undamaged accessory. After inspecting and
installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum
no-load speed for one minute. Damaged ac-
cessories will normally break apart during this
test time.
- Wear personal protective equipment. Depend-
ing on application, use face shield, safety gog-
gles or safety glasses. As appropriate, wear
dust mask, hearing protectors, gloves and
workshop apron capable of stopping small
abrasive or workpiece fragments. The eye
protection must be capable of stopping fl ying
debris generated by various operations . The
dust mask or respirator must be capable of
fi ltrating particles generated by your operation.
Prolonged exposure to high intensity noise may
cause hearing loss.
- Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken ac-
cessory may fl y away and cause injury beyond
immediate area of operation.
- Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting
a “live” wire may make exposed metal parts of
the power tool “live” and shock the operator.
- Position the cord clear of the spinning acces-
sory. If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled
into the spinning accessory.
- Never lay the power tool down until the acces-
sory has come to a complete stop. The spinning
accessory may grab the surface and pull the
power tool out of your control.
- Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
- Regularly clean the power tool’s air vents. The
motor’s fan will draw the dust inside the hous-
ing and excessive accumulation of powdered
metal may cause electrical hazards.
- Do not operate the power tool near fl ammable
materials. Sparks could ignite these materi-
als.
- Do not use accessories that require liquid cool-
ants. Using water or other liquid coolants may
result in electrocution or shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in
turn causes the uncontrolled power tool to be
forced in the direction opposite of the accessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into
the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump
toward or away from the operator, depending on
direction of the wheel’s movement at the point of
pinching. Abrasive wheels may also break under
these conditions.
Kickback is the result of power tool misuse and/
or incorrect operating procedures or conditions
and can be avoided by taking proper precautions
as given below.
- Maintain a fi rm grip on the power tool and po-
sition your body and arm to allow you to resist
kickback forces. Always use auxiliary handle,
if provided, for maximum control over kick-
back or torque reaction during start-up. The
operator can control torque reactions or kick-
back forces, if proper precautions are taken.
- Never place your hand near the rotating acces-
sory. Accessory may kickback over your hand.
- Do not position your body in the area where
power tool will move if kickback occurs. Kick-
back will propel the tool in direction opposite
to the wheel’s movement at the point of snag-
ging.
- Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
- Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent
kickback and loss of control.
Содержание
- Ras 180 3 e hr 1
- Warnung 8
- Vorsicht 9
- Warnung 10
- Warning 14
- Caution 15
- Warning 16
- Avertissement 19
- Avertissement 20
- Avertissement 21
- Prudence 21
- Atención 27
- Avviso 31
- Prudenza 32
- Avviso 33
- Waarschuwing 37
- Voorzichtig 38
- Waarschuwing 38
- Waarschuwing 39
- Varning 43
- Varning 44
- Varoitus 48
- Varoitus 50
- Advarsel 53
- Forsigtig 54
- Advarsel 55
- Advarsel 58
- Forsiktig 59
- Advarsel 60
- Advertência 63
- Advertência 64
- Advertência 65
- Cuidado 65
- Предупреждение 69
- Предупреждение 70
- Внимание 71
- Предупреждение 71
- Výstraha 75
- Výstraha 77
- Ostrzeżenie 80
- Ostrzeżenie 81
- Ostrożnie 82
- Ostrzeżenie 82
Похожие устройства
- Sharp AY-XPM9CR Инструкция по эксплуатации
- Camelion CF20-AS/827/E27 3 шт. Инструкция по эксплуатации
- Hitachi RAS-14LH1 / RAC-14LH1 Инструкция по эксплуатации
- Roland QUAD-CAPTURE Инструкция по эксплуатации
- Honda Accord CU1 (2009 г.) регламент ТО Инструкция по эксплуатации
- Casio FX-991ES Инструкция по эксплуатации
- Sharp AY-XPM7CR Инструкция по эксплуатации
- Camelion FC15 E27 Инструкция по эксплуатации
- AEG 413200 EX 150 E Инструкция по эксплуатации
- Hitachi RAS-10LH1 / RAC-10LH1 Инструкция по эксплуатации
- Roland OCTA-CAPTURE UA-1010 Инструкция по эксплуатации
- Honda Accord CU2 (2009 г.) регламент ТО Инструкция по эксплуатации
- Casio FX-82ES-SA-EH-D Инструкция по эксплуатации
- Hitachi RAS-08LH1 / RAC-08LH1 Инструкция по эксплуатации
- Sharp AY-XPM12CR Инструкция по эксплуатации
- Fubag TSMIG 180 Инструкция по эксплуатации
- Roland DUO-CAPTURE Инструкция по эксплуатации
- Honda CR-V RD8 (2002 г.) регламент ТО Инструкция по эксплуатации
- Sharp AY-XP9FR Инструкция по эксплуатации
- AEG 416100 EХ 125 ES Инструкция по эксплуатации
Скачать
Случайные обсуждения
Ответы 0
Разобрал теперь желательно посмотреть схему регулировки оборотов кто подскажет?
4 года назад