![AMERICAN DJ Vizi QWash7 Руководство по эксплуатации онлайн [20/24] 758163](/img/pdf.png)
AMERICAN DJ Vizi QWash7 Руководство по эксплуатации онлайн [20/24] 758163
![AMERICAN DJ Vizi QWash7 Руководство по эксплуатации онлайн [20/24] 758163](/views2/1989878/page20/bg14.png)
ADJ Products, LLC - www.adj.com - Vizi Q Wash7 Instruction Manual Page 39ADJ Products, LLC - www.adj.com - Vizi Q Wash7 Instruction Manual Page 38
Vizi Q Wash7 System Menu
Calibrate - With this function you can calibrate and adjust the eects
wheels to their correct positions. The Calibration password 050.
NOTE: ONLY QUALIFIED TECHNICIANS SHOULD PERFORM
THIS FUNCTION.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Test” is highlighted, then press ENTER.
2. Press the LEFT or RIGHT buttons until “Calibrate” is displayed,
press ENTER.
3. “XXXX” will be displayed. The password is 050.
4. Press ENTER to conrm or press MODE to exit.
PROGRAM
EDIT PROGRAM: - The xture comes equipped with a built-in DMX
recorder that allows custom programs to be installed and recalled
directly from the xture’s control board. Programs can be created and
stored using the xture’s control board or by using an external DMX
controller.
Select. Pro – This function allows the user to select one of nine of
the user dened built-in programs. This program is then accessed in
“Function Mode” under “Program Run.”
Edit. Pro – This function allows the user to edit the built-in programs.
Edit. Sce – This function allows the user to edit or dene the actual
scenes that are stored in the user dened built-in programs that are
accessed in the previous step.
Sce. Input - The Vizi Q Wash7 features an integrated DMX recorder.
Preprogrammed scenes can be transmitted to the xture via any
DMX compliant controller. This function allows those scenes to be
stored in to the xture’s built-in memory and then subsequently used
to create the user-dened programs.
Vizi Q Wash7 System Menu
2. Press the LEFT or RIGHT buttons until “Software. V” is displayed,
press ENTER.
3. The software version will now be displayed.
4. Press MODE to exit.
TEST
Reset. M - With this function you can reset the Pan & Tilt motors.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Test” is highlighted, then press ENTER.
2. Press the LEFT or RIGHT buttons until “Reset. M” is displayed.
3. Press ENTER to reset or press MODE to exit.
Test. Chan - With this function you can test each channel function.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Test” is highlighted, then press ENTER.
2. Press the LEFT or RIGHT buttons until “Test. Chan” is displayed,
press ENTER.
3. Use the LEFT or RIGHT buttons to scroll through the various chan-
nels.
4. Press ENTER to select a channel to test or press MODE to exit.
Panel. Ctrl - With this function you can make ne adjustments.
1. Press the MODE button to access the main menu. Press the UP or
DOWN buttons so that “Test” is highlighted, then press ENTER.
2. Press the LEFT or RIGHT buttons until “Panel. Ctrl” is displayed,
press ENTER.
3. Use the LEFT or RIGHT buttons to scroll through the various func-
tions.
4. Press ENTER when you nd the function you would like to adjust
or press MODE to exit.
Содержание
- User instructions 1
- Vizi q wash7 1
- Customer support 2
- Introduction 2
- Table of contents 2
- Unpacking 2
- Unpacking introduction customer support safety precautions features handling precautions registration mounting dmx set up 11 dmx control 2 dmx traits 3 21 color macro chart 2 system menu 3 operation 0 photometric chart 2 43 dimmer curve chart 4 fuse replacement 4 cleaning 5 trouble shooting 5 warranty 6 specifications 7 2
- Warning 2
- Caution 3
- Dmx 512 5
- Notice the suitable enviromental temperature for this light ing fixture is between 25 c to 45 c do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above this will allow the fixture to run at its best and help prolong the fixture life 5
- Power supply 5
- Screw one clamp each via a m12 screw and nut onto the omega holders insert the quick lock fasteners of the omega holders into the respective holes on the bottom of the vizi q wash7 tighten the quick lock fasteners fully clockwise install the second omega holder pull the safety cable through the holes on the bottom of the base and over the trussing system or a safe fixation spot insert the end in the carabine and tighten the safety screw 5
- A male and female xlr connector on either end of the cable also remember that dmx cable must be daisy chained and cannot be split 6
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior 6
- Conductor 5 pin xlr male in 3 pin xlr female out 6
- Data compliment signal 6
- Data true signal 6
- Ground shield 6
- Not used 6
- Notice 6
- Pin 4 do not use 6
- Pin 5 do not use 6
- Pin xlr dmx connectors 6
- Pin xlr to 5 pin xlr conversion 6
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion 6
- Special note line termination 6
- Vizi q wash7 dmx set up 6
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior 6
- Adj products llc www adj com vizi q wash7 instruction manual page 23 adj products llc www adj com vizi q wash7 instruction manual page 22 12
- Vizi q wash7 color macro chart 12
- Vizi q wash7 system menu 12
- Now set the dmx value of channel 2 to the value 7 to adjust the starting address between 1 and 255 to adjust the address between 256 and 511 set channel 2 to the value 8 13
- On your dmx controller set the dmx value of channel 1 to the value 7 13
- Set the dmx value of channel 3 to your desired start ing address this will take about 20 seconds before the unit accepts the new dmx address example if you want the address to be 57 you must first set 13
- To use this function follow these instructions to adjust the address of your unit you must first go to the address that it is currently set to from there you can adjust the address first make sure all channels are set to the value of 0 13
- Nd example if you want the address to be 420 you must first set the address that is currently assingned to the unit if you want the set the address to 420 set channel 1 s value to 7 channel 2 s value to 8 and channel 3 s to 164 256 164 420 14
- The address that is currently assingned to the unit then set channel 1 s value to 7 channel 2 s value to 7 and chan nel 3 s value to 57 wait 20 seconds and the address should change on the unit to 57 14
- Master slave cofiguration auto program 21
- Stand alone auto program 21
- 1 2 3 4 5 22
- 1 3 5 8 10 22
- Beam opening m 22
- Intensity lux 22
- Fixture cleaning 23
- A d j supply europe b v 24
- Adj products llc 24
- Adj products llc www adj com vizi q wash7 instruction manual page 46 24
- Auto sensing voltage 24
- Beam angle 7 58 degrees 24
- Channels or 23 channels 19 channels or 23 channels 24
- Colors rgbw 24
- Dimensions 11 5 l x 8 w x 15 5 h 24
- Dmx 3 dmx channel modes 17 channels 24
- Duty cycle none 24
- Ew kerkrade 24
- Fixtures max 240v 11 fixtures max 240v 24
- Fuse 3a 120v 2a 240v 24
- Junostraat 2 24
- Led life 50 000 hrs 24
- Leds 7 x 40w rgbw 4 in 1 leds 24
- Model vizi q wash7 24
- Please note 24
- Power consumption 305w 24
- Powercon daisy chain 5 fixtures max 110v 24
- S eastern ave los angeles ca 90040 usa 24
- Service adjgroup eu www adj eu 24
- Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 24
- Tel 31 45 546 85 00 fax 31 45 546 85 99 24
- Tel 323 582 2650 fax 323 725 6100 24
- The netherlands 24
- This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source 24
- Vizi q wash7 specifications 24
- Vizi q wash7 warranty 24
- Voltage 100 240v 50 60hz 24
- Warranty 2 year 730 days 24
- Web www adj com e mail info americandj com 24
- Weight 19 lbs 8 kgs 24
- Working position any safe secure position 24
- X 200 x 400mm 300 x 200 x 400mm 24
Похожие устройства
- APart OVO5T-W Руководство по эксплуатации
- APart OVO5T-BL Руководство по эксплуатации
- APart OVO5-BL Руководство по эксплуатации
- APart OVO5P-W Руководство по эксплуатации
- APart OVO3-W Руководство по эксплуатации
- APart OVO3T-BL Руководство по эксплуатации
- APart OVO3-BL Руководство по эксплуатации
- APart NETKIT-RS Руководство по эксплуатации
- APart NETKIT-IR Руководство по эксплуатации
- APart MPLT62G Руководство по эксплуатации
- APart OVO3T-W Руководство по эксплуатации
- APart MPLT32-G Руководство по эксплуатации
- APart MP26-G Руководство по эксплуатации
- APart MP16-G Руководство по эксплуатации
- APart MPBD20-G Руководство по эксплуатации
- APart MICPAT-6 Руководство по эксплуатации
- APart MASK8F-BL Руководство по эксплуатации
- APart MASK8-W Руководство по эксплуатации
- APart MASK8-BL Руководство по эксплуатации
- APart MASK2-BL Руководство по эксплуатации