![AMERICAN DJ Vizi QWash7 [3/24] Caution](/img/pdf.png)
AMERICAN DJ Vizi QWash7 [3/24] Caution
![AMERICAN DJ Vizi QWash7 [3/24] Caution](/views2/1989878/page3/bg3.png)
For Your Own Personal Safety, Please Read and Understand This
Manual Completely Before You Attempt To Install Or Operate
This Unit!
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt-
age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken.
• Do not attempt to remove or break o the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 45 for cleaning details.
• Heat -This fixture should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a
marked change in performance.
Vizi Q Wash7 Safety Precautions
ADJ Products, LLC - www.adj.com - Vizi Q Wash7 Instruction Manual Page 4
• DMX-512 Protocol Compatible (3 DMX Modes: 17 DMX Channel
Mode, 19 DMX Channel Mode, and 23 DMX Channel Mode)
• Pan & Tilt Invert
• PowerCON Inputs & Outputs
• 3-Pin & 5-Pin XLR Inputs & Outputs
• Color Macros + Individual RGBW Control
• 2 Operating Modes - Auto Program & DMX Control
• Built-In ADJ’s WiFly EXR Wireless DMX Up to 2,500 feet/760M
• Stand Alone Setup or Master-Slave Configuration
• Edit and Save Scenes into the Memory
Vizi Q Wash7 Features
ADJ Products, LLC - www.adj.com - Vizi Q Wash7 Instruction Manual Page 5
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.
During operation the housing may become extremely hot. Avoid touch-
ing the unit with bare hands while in use.
ADJ Products, LLC will not accept any liability for any resulting dam-
ages caused by the non-observance of this manual or any unauthor-
ized modication to this unit.
Vizi Q Wash7 Handling Precautions
The Vizi Q Wash7 carries a two year limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-
paid and accompany a return authorization (R.A.) number. The R.A.
number must be clearly written on the outside of the return package.
A brief description of the problem as well as the R.A. number must
also be written down on a piece of paper and included in the shipping
carton. If the unit is under warranty, you must provide a copy of your
proof of purchase invoice. You may obtain a R.A. number by con-
tacting our customer support team on our toll free customer support
number. All packages returned to the service department not display-
ing a R.A. number on the outside of the package will be returned to
the shipper at the shippers cost.
Vizi Q Wash7 Product Registration
Содержание
- User instructions 1
- Vizi q wash7 1
- Customer support 2
- Introduction 2
- Table of contents 2
- Unpacking 2
- Unpacking introduction customer support safety precautions features handling precautions registration mounting dmx set up 11 dmx control 2 dmx traits 3 21 color macro chart 2 system menu 3 operation 0 photometric chart 2 43 dimmer curve chart 4 fuse replacement 4 cleaning 5 trouble shooting 5 warranty 6 specifications 7 2
- Warning 2
- Caution 3
- Dmx 512 5
- Notice the suitable enviromental temperature for this light ing fixture is between 25 c to 45 c do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above this will allow the fixture to run at its best and help prolong the fixture life 5
- Power supply 5
- Screw one clamp each via a m12 screw and nut onto the omega holders insert the quick lock fasteners of the omega holders into the respective holes on the bottom of the vizi q wash7 tighten the quick lock fasteners fully clockwise install the second omega holder pull the safety cable through the holes on the bottom of the base and over the trussing system or a safe fixation spot insert the end in the carabine and tighten the safety screw 5
- A male and female xlr connector on either end of the cable also remember that dmx cable must be daisy chained and cannot be split 6
- Be sure to follow figures two and three when making your own cables do not use the ground lug on the xlr connector do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the xlr s outer casing grounding the shield could cause a short circuit and erratic behavior 6
- Conductor 5 pin xlr male in 3 pin xlr female out 6
- Data compliment signal 6
- Data true signal 6
- Ground shield 6
- Not used 6
- Notice 6
- Pin 4 do not use 6
- Pin 5 do not use 6
- Pin xlr dmx connectors 6
- Pin xlr to 5 pin xlr conversion 6
- Some manufactures use 5 pin dmx 512 data cables for data transmission in place of 3 pin 5 pin dmx fixtures may be implemented in a 3 pin dmx line when inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores the chart below details a proper cable conversion 6
- Special note line termination 6
- Vizi q wash7 dmx set up 6
- When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior a terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male xlr connector data and data this unit is inserted in the female xlr connector of the last unit in your daisy chain to terminate the line using a cable terminator adj part number z dmx t will decrease the possibilities of erratic behavior 6
- Adj products llc www adj com vizi q wash7 instruction manual page 23 adj products llc www adj com vizi q wash7 instruction manual page 22 12
- Vizi q wash7 color macro chart 12
- Vizi q wash7 system menu 12
- Now set the dmx value of channel 2 to the value 7 to adjust the starting address between 1 and 255 to adjust the address between 256 and 511 set channel 2 to the value 8 13
- On your dmx controller set the dmx value of channel 1 to the value 7 13
- Set the dmx value of channel 3 to your desired start ing address this will take about 20 seconds before the unit accepts the new dmx address example if you want the address to be 57 you must first set 13
- To use this function follow these instructions to adjust the address of your unit you must first go to the address that it is currently set to from there you can adjust the address first make sure all channels are set to the value of 0 13
- Nd example if you want the address to be 420 you must first set the address that is currently assingned to the unit if you want the set the address to 420 set channel 1 s value to 7 channel 2 s value to 8 and channel 3 s to 164 256 164 420 14
- The address that is currently assingned to the unit then set channel 1 s value to 7 channel 2 s value to 7 and chan nel 3 s value to 57 wait 20 seconds and the address should change on the unit to 57 14
- Master slave cofiguration auto program 21
- Stand alone auto program 21
- 1 2 3 4 5 22
- 1 3 5 8 10 22
- Beam opening m 22
- Intensity lux 22
- Fixture cleaning 23
- A d j supply europe b v 24
- Adj products llc 24
- Adj products llc www adj com vizi q wash7 instruction manual page 46 24
- Auto sensing voltage 24
- Beam angle 7 58 degrees 24
- Channels or 23 channels 19 channels or 23 channels 24
- Colors rgbw 24
- Dimensions 11 5 l x 8 w x 15 5 h 24
- Dmx 3 dmx channel modes 17 channels 24
- Duty cycle none 24
- Ew kerkrade 24
- Fixtures max 240v 11 fixtures max 240v 24
- Fuse 3a 120v 2a 240v 24
- Junostraat 2 24
- Led life 50 000 hrs 24
- Leds 7 x 40w rgbw 4 in 1 leds 24
- Model vizi q wash7 24
- Please note 24
- Power consumption 305w 24
- Powercon daisy chain 5 fixtures max 110v 24
- S eastern ave los angeles ca 90040 usa 24
- Service adjgroup eu www adj eu 24
- Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice 24
- Tel 31 45 546 85 00 fax 31 45 546 85 99 24
- Tel 323 582 2650 fax 323 725 6100 24
- The netherlands 24
- This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source 24
- Vizi q wash7 specifications 24
- Vizi q wash7 warranty 24
- Voltage 100 240v 50 60hz 24
- Warranty 2 year 730 days 24
- Web www adj com e mail info americandj com 24
- Weight 19 lbs 8 kgs 24
- Working position any safe secure position 24
- X 200 x 400mm 300 x 200 x 400mm 24
Похожие устройства
- APart OVO5T-W Руководство по эксплуатации
- APart OVO5T-BL Руководство по эксплуатации
- APart OVO5-BL Руководство по эксплуатации
- APart OVO5P-W Руководство по эксплуатации
- APart OVO3-W Руководство по эксплуатации
- APart OVO3T-BL Руководство по эксплуатации
- APart OVO3-BL Руководство по эксплуатации
- APart NETKIT-RS Руководство по эксплуатации
- APart NETKIT-IR Руководство по эксплуатации
- APart MPLT62G Руководство по эксплуатации
- APart OVO3T-W Руководство по эксплуатации
- APart MPLT32-G Руководство по эксплуатации
- APart MP26-G Руководство по эксплуатации
- APart MP16-G Руководство по эксплуатации
- APart MPBD20-G Руководство по эксплуатации
- APart MICPAT-6 Руководство по эксплуатации
- APart MASK8F-BL Руководство по эксплуатации
- APart MASK8-W Руководство по эксплуатации
- APart MASK8-BL Руководство по эксплуатации
- APart MASK2-BL Руководство по эксплуатации